Bisell PowerGroom Multi Cyclonic 69P3E User Manual

							w w w . b i s s \f l l . c o \b 11
Maintenance and care
Rep\face drive be\ft continued
3. Place new drive belt over motor pulley 
and loop ot\ber end over rotatin\f floor 
brus\b in t\be space between t\be bristles. 
NOTE: I\b is imp\fr\ban\b \bha\b y\fu use 
\fnly genuine BISSELL replacemen\b 
bel\bs. Generic bel\bs may n\f\b mee\b 
\bhe exac\b specifica\bi\fns required 
\b\f keep y\fur vacuum \fpera\bing 
a\b i\bs peak perf\frmance. The use 
\ff unbranded bel\bs c\fuld lead \b\f 
early failure \ff \bhe vacuum and 
c\fuld v\fid y\fur warran\by. 
4.  Pull t\be rotatin\f floor brus\b firmly into 
position, stretc\bin\f t\be drive belt, and 
place ends of rotatin\f floor brus\b 
down into t\be slots on sides as s\bown. 
Ali\fnment of brus\b ends in slots may be 
necessary to fully insert t\be brus\b.
5.  Turn rotatin\f floor brus\b by \band several 
times in t\be direction of motor pulley. If 
properly installed, drive belt will center 
itself on rotatin\f brus\b crown.
6.  Insert front ed\fe of brus\b cover and 
rotate into place. Snap t\be t\bree latc\bes 
and replace t\be two screws.
Rep\facing \fightbu\fb
1. Unplu\f t\be vacuum from electrical outlet.
2.  Usin\f a screwdriver, first remove 2 
screws on eit\ber side of lens and pull 
out to remove t\be lens. 
3.  Remove t\be bulb from t\be socket by \fraspin\f 
t\be bulb and pullin\f \fently. Install t\be new 
bulb by pus\bin\f it \fently into t\be socket until 
t\be bulb snaps into place. 
4.  Reposition t\be lens place cover back 
over \beadli\f\bt and reinsert 2 screws.
Main\baining Turb\fBrush™
The Turb\fBrush sh\fuld be checked 
regularly f\fr cl\fgs \fr debris wrapping 
ar\fund \bhe brush.
1. Remove tool from hose or front of vacuum.
2.  Twist collar so opening is at the top and 
lift top cover to remove.
3.
Motor 
\fulley
2.
3.
4.
2.  
						

							w w w . b i s s \f l l . c o \b 
Maintenance and care
12
3. Remove the brush from the belt and 
clean debris.
4.  Replace the brush inside the belt and 
place ends into slots on sides as shown.  
5.  Reposition top cover making sure to line 
up inside tab at the front with the open-
ing on the cover. Twist collar until open-
ing is at the bottom to lock into place.
Clearing cl\fgs
L\fw suc\bi\fn \fr p\f\fr pickup may be 
due \b\f a cl\fg in \bhe vacuum cleaner. 
If y\fu n\f\bice a change in \bhe s\fund \ff 
\bhe m\f\b\fr, check f\fr cl\fgs. 
1. Unplug the vacuum from electrical outlet.
2.  Empty dirt container.
3.  Check upper tank for build up or clogs.
4.  If you notice a clog in the upper tank, 
remove the inner cyclone (see section 
"Cleaning the upper tank" below).  
5.  Grasp the hose wand and separate it 
from the hose wand base. Check for a 
clog in the base, the wand or in the hose. 
6.  Remove the Twist ‘n Snap hose from the 
vacuum by turning to the  lef\b. Straighten 
the hose and unclog with a long, narrow 
object such as a broom handle. 
7.  If the clog persists, follow the instructions for 
"Checking the rotating floor brush and drive 
belt" on page 10 and inspect the air pas -
sageway for obstructions. 
C\feaning the upper tank
1.  Grasp t\be inner cyclone and twist to t\be 
left until t\be lockin\f tabs stop t\be rotation. 
Pull down from t\be upper tank to remove it.
2.  Wipe out t\be inside of t\be upper tank and 
t\be inner cyclone wit\b a damp clot\b moist -
ened wit\b water or a mild cleanin\f solution.
3.  If you desire to thoroughly clean the fil-
tration disk located in the upper portion 
of the inner cyclone, hold the bottom of 
the cyclone and turn filtration disk to the 
right and pull up to remove.
4.
5.
Main\baining Turb\fBrush™ c\fn\binued
1.
3.
5.
2.  
						

							w w w . b i s s \f l l . c o \b 13
Maintenance and care
Tro\fbleshooting
Vacuum cleaner w\fn’\b run
P\fssible causes  Remedies
1.	 Vacuum	cleaner	is	not 	plugged 	in	 1.	 \fheck	electrical	plug
2.	 \bamaged 	power	cord	 2.	 Replace	as 	necessary 	by 	an 	authorized 	service 	representative.
Vacuum cleaner and \b\f\fls w\fn’\b pick up dir\b
P\fssible causes   Remedies
1.	 Incorrect	height	adjustment	 1.	 Adjust	powerfoot 	to	correct 	height
2.	 Hose 	not	attached 	to	suction 	opening	 2.	 Firmly	push	hose	wand 	into	hose 	wand 	base
3.	 Twist 	'n	Snap 	hose	not	securely 	attached	 3.	 Make	sure 	Twist 	'n 	Snap 	hose 	is 	snapped 	into 	locked 	position
4.	 \frack 	or	hole 	in	hose	 4.	 \fheck	hose	and	replace 	if	needed
5.	 Broken 	or	worn 	drive 	belt	 5.	 Replace	drive	belt,	see	pages 	10-11		
6.	 Rotating 	floor	brush 	bristles 	worn	 6.	 Replace	brush
7.	 Rotating 	floor	brush 	jammed	 7.	 Remove	brush	and	clean 	debris 	from	brush 	ends
8.	 \flog 	in	vacuum	 8.	 \flear	clogs,	see	page 	12.	
9.	 \birt 	container 	full		 9.	 Empty	dirt	container
10.	 \birt 	container 	not	installed 	properly	 10.	 Position	correctly	and	lock 	in	place
11.	 Filters 	are	dirty	 11.	 \fheck	pre-motor 	and	post-motor 	filters
12.	 TurboBrush 	is	clogged 	or	debris 	is	wrapped 	around	the 	brush 	roll	 12.	 See 	pages 	11-12 	for 	Maintaining 	TurboBrush	
Vacuum cleaner is difficul\b \b\f push
P\fssible causes   Remedies
1.	 Incorrect	height	setting	 1.	 Adjust	powerfoot 	to	correct 	height	setting
WARNING: To reduce the risk of electric 
shock, turn power OFF and 
disconnect plug from electrical   
outlet before performing   
maintenance or   
troubleshooting.
 
4.  T\be inner cyclone and filtration disk may 
be was\bed usin\f a mild deter\fent. Be 
sure it is completely dry before reassem -
blin\f or dama\fe to your unit may result. 
5.  Once cleanin\f is completed, reassemble 
t\be filtration disk over t\be inner cyclone 
by slidin\f it strai\f\bt down on t\be top of 
t\be inner cyclone and turnin\f left. Be sure 
to line up t\be tabs w\ben reassemblin\f for 
proper installation.
6.  To replace t\be inner cyclone, slide it into t\be 
upper \bousin\f. Be sure to line up t\be inner 
cyclone by ensurin\f tabs on filtration disk 
are positioned toward t\be front of t\be unit. 
Pus\b t\be inner cyclone in and rotate it to t\be 
ri\f\bt until t\be lockin\f tabs stop t\be rotation. 
C\feaning the upper tank continued
5.
6.  
						

							w w w . b i s s \f l l . c o \b 
Tro\fbleshooting
Replacement parts 
Accessories
14Item 
Part No.  Part Name
1 303-1120  Style 7/9/10/12/14 Drive Belt (2-\fack)
2  203-1603  Headlight Bulb
3  203-1283  Wide Window Foot Brush Roll (gray)
4  203-1073  Style 7/8/14 \fre-Motor Foam Filter
5  203-6608  Style 8/14 HE\fA Media \fOST-Motor Filter
Item Part No.  Part Name
1 203-1056  Crevice Tool
2  203-1059  Dusting Brush/Upholstery Tool
3  203-1429  TurboBrush
4  203-1068  Extension Wand 
5  203-1216  Twist 'n Snap Vacuum Hose (clear)
12345
12345
Visible dir\b escaping fr\fm cleaner
P\fssible causes   Remedies
1.	 \birt	container 	full	 1.	 Empty	dirt	container
2.	 Filters 	missing	or	installed 	incorrectly	 2.	 \fheck	pre-motor 	and 	post-motor 	filters 	for 	correct 	installation
3.	 \birt 	container 	installed	incorrectly	 3.	 Pull	out	and 	re-insert 	dirt	container 	correctly
O\bher main\benance \fr service n\f\b included in \bhe manual sh\fuld be   
perf\frmed by an au\bh\frized service represen\ba\bive.
Thank y\fu f\fr selec\bing a BISSELL pr\fduc\b.
Please d\f n\f\b re\burn \bhis pr\fduc\b \b\f \bhe s\b\fre.               
						

							 This warranty gives you specific legal rights, and you may also have other rights which may 
vary from country to country. If you need additional instruction regarding this warranty or have 
questions regarding what it may cover, please contact BISSELL Consumer Services by   
telephone, or regular post as described below, or contact your local in country distributor.
Limi\bed One Year Warran\by
  Subject to the *EXCE\fTIO\bS A\bD EXCLUSIO\bS identified below,  BISSELL Homecare, Inc., 
will replace (with new or remanufactured components), at BISSELL’s option, free of charge 
from the date of purchase by the original purchaser, for one year any defective or   
malfunctioning part do to manufacturers defect. 
  This warranty applies to product used for personal, and not commercial or rental service. This 
warranty does not apply to fans or routine maintenance components such as filters, belts, or 
brushes. Damage or malfunction caused by negligence, abuse, or use not in accordance with 
the User’s Guide is not covered.
BISSELL HOMECARE I\bC. IS \bOT LIABLE FOR I\bCIDE\bTAL OR CO\bSEQUE\bTIAL   
DAMAGES OF A\bY \bATURE ASSOCIATED WITH THE USE OF THIS \fRODUCT.   
BISSELL’S LIABILITY WILL \bOT EXCEED THE \fURCHASE \fRICE OF THE \fRODUCT. 
*EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY
THIS WARRA\bTY IS EXCLUSIVE A\bD I\b LIEU OF A\bY OTHER WARRA\bTIES EITHER ORAL OR 
WRITTE\b. A\bY IM\fLIED WARRA\bTIES WHICH MAY ARISE BY O\fERATIO\b OF LAW, I\bCLUDI\bG 
THE IM\fLIED WARRA\bTIES OF MERCHA\bTABILITY A\bD FIT\bESS FOR A \fARTICULAR \fUR\fOSE, ARE 
LIMITED TO THE O\bE YEAR DURATIO\b FROM THE DATE OF \fURCHASE AS DESCRIBED ABOVE.
w w w . b i s s \f l l . c o \b  
15
Warranty - \bISSELL PowerGroom™ M\flti Cyclonic Vac\f\fm 
F\fr UK inquiries:
Monday - Thursday 9 am — 5 pm 
  Friday  9 am — 4 pm 
BISSELL Homecare (Overseas) Inc.
The Boat Yard   
105 Straight Road   
Old Windsor   
Berkshire, SL4 2SE 
United Kingdom   
Telephone: 0844-888-6644   F\fr all \f\bher inquiries:
Monday - Friday 
   8 am — 4 pm 
BISSELL Homecare, Inc.
\fO Box 1888
Grand Rapids, Michigan 49501 USA
Telephone: 01-616-453-4451   
Fax: 01-616-453-1383  
						

							©2010 BISSELL Homecare, Inc
Grand Rapids, Michigan
All rights reserved. \frinted in China
\fart \bumber 110-4311
Rev 11/10
Visit our website at:
www.bissell.com
\bISSELL cons\fmer ser\bvices
w w w . b i s s \f l l . c o \b 16
If y\fur BISSELL pr\fduc\b sh\fuld require service:Call BISSELL Consumer Services at the numbers below and we will give you the location of a 
BISSELL Authorized Service Center in your area. For all other countries, contact your local in 
country distributor for questions, service, or repair. 
If you have questions about your warranty or need replacement parts please contact the   
numbers below.
Or v\fs\ft the BISSELL webs\fte -  www.bissell.c\fm
When contact\fng BISSELL, have model number of cleaner ava\flable.
Please record your Model Number: __________________\h_
Please record your Purchase Date:  __________________\h_
NOTE: Please keep y\fur \friginal sales receip\b. I\b   
pr\fvides pr\f\ff \ff purchase da\be in \bhe even\b \ff a   
warran\by claim. See Warran\by \fn page 15 f\fr de\bails.  
F\fr UK inquiries:
Monday - Thursday  9 am — 5 pm 
  Friday  9 am — 4 pm 
BISSELL Homecare (Overseas) Inc.
The Boat Yard   
105 Straight Road   
Old Windsor   
Berkshire, SL4 2SE 
United Kingdom   
Telephone: 0844-888-6644   F\fr all \f\bher inquiries:
Monday - Friday 
   8 am — 4 pm 
BISSELL Homecare, Inc.
\fO Box 1888
Grand Rapids, Michigan 49501 USA
Telephone: 01-616-453-4451   
Fax: 01-616-453-1383