Bisell PowerForce Bagless 75Q1E User Manual

							for any technical queries, please contact  
our Technical Helpline at 0845 300 7775
11
Replace drive belt
Use only  bISSE ll Style 10 replacement belts in 
your  bISSE ll Power force  bagless.
1.  Unplug cleaner from electrical outlet.
2.  With rotating floor brush removed from vacuum 
cleaner (Steps 1-4 of "Check rotating floor brush 
and drive belt"), grasp old drive belt and remove 
from motor pulley. Discard old drive belt.
3.  Place new drive belt over motor pulley and 
stretch other end over rotating floor brush in 
the space between the bristles.
4.  Place ends of rotating floor brush down into 
slots on sides as shown.
5.  Turn rotating floor brush by hand several times 
in direction of motor pulley. If properly installed, 
drive belt will center itself on rotating brush.
6.  Reposition brush cover and replace four 
screws. Make sure end of brush cover is 
snapped into place.
Maintenance and care
Brush 
Cover 
						

							for any technical queries, please contact  
our Technical Helpline at 0845 300 7775
12
Troubleshooting
Vacuum cleaner won’t turn onPossible causes   Remedies
1.  Power cord not firmly plugged in  1.  Check electrical plug
Vacuum cleaner won't pick up dirtPossible causes    Remedies
1.  Incorrect height adjustment   1.  Adjust powerfoot to correct height setting
2.   Hose not attached to suction opening  2.  Grasp Quick Release handle and firmly push 
    hose wand onto the suction opening.
3.   Twist 'n Snap hose not securely attached  3.  Make sure Twist 'n Snap hose is snapped 
    into locked position
4.   Crack or hole in hose   4.  Check hose and replace if needed
WAR nIn G:   To reduce the risk of electric 
shock, turn power switch 
Off  and disconnect plug 
from electrical outlet before 
performing maintenance or 
troubleshooting.
Clearing clog
l ow suction, poor pickup or no suction may be 
due to a clog in the vacuum cleaner. If you notice 
a change in the sound of the vacuum motor or a 
reduction in the spinning action in the dirt   
container, check for clogs.
1.  Unplug cleaner from electrical outlet.
2.  Empty dirt container.
3. 
Check upper tank and primary separator for 
build up or clogs. Check to make sure primary 
separator is installed correctly. To unlock the primary separator, grasp the rim and turn 
toward the left. Pull straight down to remove. If 
the 
primary separator is missing or not locked 
into place, check and clear the tube in the   
center of the dirt container and properly install 
primary separator.
4.  Remove the Twist ‘n Snap hose from the 
vacuum by turning to the left. Check the 
suction inlet, hose and hose wand for clogs. 
Remove any clogs from the hose using a 
long, narrow object such as a broomstick.
5.  Check the foot hose for clogs. If needed, 
remove the screw attaching the hose wand 
base to the vacuum. Straighten the foot hose 
and unclog with a long, narrow object such 
as a broomstick.
6.  If the clog persists, follow the instructions for 
checking the rotating floor brush on page 10 
and inspect the air passageway for obstructions.
Maintenance and care
Air Passageway
Suction Inlet
Primary Separator
Hose  
Wand Base 
						

							for any technical queries, please contact  
our Technical Helpline at 0845 300 7775
Troubleshooting
Vacuum cleaner won't pick up dirt (continued)Possible causes    Remedies
5.  Broken or worn drive belt   5.  Replace drive belt, see page 11
6.   Rotating floor brush bristles worn  6.  Replace brush
7.   Rotating floor brush jammed   7.  Remove brush and clean debris from brush ends
8.   Clog in vacuum   8.  Follow instructions for clearing 
    clogs on page 12
9.   Dirt container full   9.  Empty dirt container
10.  Dirt container not installed properly  10. Position correctly and lock in place
11.  Filters are dirty   11. Check and clean inner and outer circular 
    filters, pre-motor and post-motor filters
12.  
Primary separator missing or installed incorrectly  12. Check for a clog in the tube in the center of the 
    dirt container, clear and properly install   
    primary separator
Tools won't pick up dirtPossible causes   Remedies
1.  Crack or hole in hose   1.  Check hose and replace if needed
2.   Vacuum hose, wand or tools clogged  2.  Follow instructions for clearing clogs on 
    page 12
3.   Dirt container full   3.  Empty dirt container
4.   Dirt container or upper tank not installed properly  4.  Position correctly and lock in place
5.   Filters are dirty   5.  Check and clean inner and outer circular 
    filters, pre-motor and post-motor filters
6.   Primary separator missing or installed incorrectly  6.  Check for a clog in the tube in the center of the 
    dirt container, clear and properly install   
    primary separator
Vacuum cleaner difficult to pushPossible causes    Remedies
1.  Incorrect height adjustment   1.  Adjust powerfoot to correct height setting
2.   Rotating floor brush not rotating  2.  Check drive belt and brush
Visible dirt escaping from cleanerPossible causes    Remedies
1.  Dirt container full   1.  Empty dirt container
2.   Filters missing or installed incorrectly  2.  Check inner and outer circular filter and 
    post-motor filter for correct installation
3.   Dirt container installed incorrectly  3.  Position correctly and lock into place
4.   Filter cup installed incorrectly  4.  Remove dirt container and make sure filter 
    cup is fully attached
13 
						

							for any technical queries, please contact  
our Technical Helpline at 0845 300 7775
14
Technical queries
for any technical queries, please contact our Technical Helpline as follows:
Tel. 0840 300 7775 
Monday -  friday   9 am — 8 pm   
Saturday - Sunday  10 am — 6 pm
When contacting our Technical  helpline, have model number of unit available.
Please record your  model Number: ___________________
Please record your Purchase Date: ___________________
note: Please keep your original sales receipt. It provides proof of date of purchase. 
						

							for any technical queries, please contact  
our Technical Helpline at 0845 300 7775
Replacement parts - BISSELL PowerForce Bagless
b elow is a list of common replacement parts. While not all of these parts may have come 
with your specific model, they are available for purchase if desired. 
Item  Part no.  Part name
1  32074  style 7/9/10/12/14 Drive Belt (2-Pack)
2  203-1056  Crevice Tool
3  203-1059  Combination Dusting Brush/Upholstery Tool 
4  203-1068  extension Wand
5  203-1069  Twist ‘n snap Vacuum  hose (select models only)
6  203-5624  Brush Roll 
7  32064  style 9/10 Inner &  outer Circular filter set
8  32065  style 9/10 Inner Circular  filter only
9  32066  style 10  outer Circular filter and Post-motor  filter set
10  203-1215  Pre-motor filter
12345
678910                  
15 
						

							for any technical queries, please contact  
our Technical Helpline at 0845 300 7775
16
©2009 BIssell  homecare, Inc
Grand Rapids,  michigan
All rights reserved. Printed in China
Part Number 110-4108
Rev 5/09
Technical Helpline:
Tel. 0840 300 7775 
Monday -  friday   9 am — 8 pm   
Saturday - Sunday  10 am — 6 pm
Produced for:
ASDA Stores  ltd
leeds
lS11 5AD
This symbol is known as the ‘Crossed-out Wheelie Bin  symbol’. When this symbol 
is marked on a product, it means that the product should not be disposed of   
with your general household waste.  only discard electrical/electronic items in 
separate collection schemes, which cater for the recovery and recycling of   
materials contained within. Your co-operation is vital to ensure the success   
of these schemes and for the protection of the environment.