Bisell Pet Hair Eraser Compact 12R8E User Manual
Have a look at the manual Bisell Pet Hair Eraser Compact 12R8E User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 201 Bissell manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
11www.bissell.com Maintenance and care Cleaning the pre-motor filter The pre-motor filter protects the motor from dirt and dust particles. 1.Unplug the vacuum from electrical outlet. 2. Open the dust bag compartment by lifting up on the latch on the door at the front of the vacuum. Lift out the dust bag holder and dust bag. 3. Remove the filter frame from the filter holder by grasping the lip of the frame and pulling up. 4. Remove the filter from the filter frame and clean by hand washing in warm water. A mild detergent can be used if desired. Allow the filter to air dry thoroughly before replacing. 5. Place the filter back into the filter frame and replace back into the filter holder. NOTE: The filter frame should be placed so the protective frame is visible. 6.Place dust bag holder and dust back into the dust bag compartment, making sure the entire bag is tucked in below the seal gasket. 7. Close dust bag compartment door and press down gently until it locks into place. Washable Pre- Motor Filter NOTICE:This product is intended for household use only and not for commercial or industrial use. Vacuuming of dust from products like plaster, concrete or ashes will damage the motor and void the warranty. Tip: For maximum cleaning performance, check the filters often and clean or replace if necessary. WARNING:Do not operate cleaner with damp or wet filters or without all filters in place. 3.
12www.bissell.com Maintenance and care The post-motor HEPA media filter assists in the filtration process to return clean air to the room. 1.Unplug the vacuum from electrical outlet. 2. Remove the filter door (located on the rear of the vacuum) by pulling up on the filter door latch. 3. Remove the post-motor HEPA media filter by grasping the lip of the filter frame and pulling up. 4. Replace the post-motor HEPA media filter with a new filter. NOTE: The post-motor filter is a white, pleated HEPA media filter. This filter is NOT washable and must be replaced when it becomes dirty. 5.Replace the filter door by inserting the two tabs at the top of the filter door and pushing down on the bottom of the filter door. Maintaining the Wide Pet TurboBrush The Wide Pet TurboBrush should be checked regularly for clogs or debris wrapping around the brush. 1.Unplug the vacuum from electrical outlet. 2. If a clog is present or debris is visible, turn the collar on the neck of the Wide Pet TurboBrush counterclockwise to the unlocked position to remove the faceplate and clear any obstructions. 3. To clean debris from the brush, remove the brush from the drive belt and clean debris. 4. Reposition the drive belt on the brush. Place the ends of the brush in the slots on the sides. Reposition the faceplate and turn the collar clockwise to the locked position. Replacing the post-motor HEPA media filter Post-Motor HEPA Media Filter 2. 3.
13www.bissell.com Troubleshooting Vacuum cleaner won’t run Possible causes Remedies 1.Vacuum cleaner is not plugged in 1.Check electrical plug 2. Power button is not pressed down 2.Press power button down Vacuum cleaner won’t pick up or low suction Possible causes Remedies 1. Tools, flex hose and/or telescoping 1.Remove each part and check for blockages extension wand are blocked 2. Filters are dirty 2.Check and clean or replace pre-motor and post-motor filters 3. Dust bag is full 3.Replace with new dust bag 4. Swivel hose not securely attached to suction opening 4.Make sure swivel hose is locked into suction opening 5. Crack or hole in flex hose 5.Check hose and replace if needed 6. Air flow regulator or variable suction power 6.Change to closed or maximum setting control is set to open or minimum setting 7. Wide Pet TurboBrush is clogged or debris 7.Check Wide Pet TurboBrush, see page 12 is wrapped around the brush Visible dust escaping from vacuum Possible causes Remedies 1 . Dust bag is full 1.Replace with new dust bag 2 . Filters missing or installed incorrectly 2.Check pre-motor and post-motor filter for correct installation 3 . Filters are dirty 3.Check and clean or replace pre-motor and post-motor filters 4 . Flex hose is blocked 4.Remove hose and check for blockages 5 . Swivel hose not securely attached to suction opening 5.Make sure swivel hose is locked into suction opening 6 . Crack or hole in flex hose 6.Check hose and replace if needed Other maintenance or service not included in the manual should be performed by an authorized service representative. Thank you for selecting a BISSELL product. Please do not return this product to the store. WARNING: To reduce the risk of electric shock, turn power OFF and disconnect plug from electrical outlet before performing maintenance or troubleshooting.
Scoresby 3179 Victoria Australia 42 Rocco Drive 0844-888-6644
Replacement parts - BISSELL Pet Hair Eraser Compact Item Part No. Part Name 1 203-7270 Dust Bag (3pk) 2 203-7276 Charcoal Odor Absorbing Packet (3pk) 3 203-7268 Pre-Motor Filter 4 203-7269 Post-Motor HEPA Media Filter 5 203-7275 Pet Hair Eraser Floor Nozzle 6 203-7277 Pet Hair Lifter 7 203-7257 Flexible Hose with Handle 8 203-7256 Telescoping Extension Wand 9 203-7279 Pet Tool Adaptor10 203-1291 Pet Contour Tool11 203-1290 Wide Pet TurboBrush12 203-7280 Combination Crevice Tool/Dusting Brush13 203-7278 Accessory Bag 1 5 9 13 2 6 10 3 7 114 8 12 15www.bissell.com
Scoresby 3179 Victoria Australia 42 Rocco Drive 0844-888-6644 mpact anister