Bisell CleanView Proheat Carpet Cleaner 34T2E User Manual

www.bissell.com 11
Operations
Carpet cleaning
1. Plug the deep cleaner into a proper 
outlet. Set ReadyTools dial to the FLOOR 
CLEANING setting. Turn the power on 
by pressing the red power switch on 
the back of the unit with your foot. Turn 
heater switch (located on side of unit) 
to the on position. Allow one minute for 
the built-in heater to warm up before 
cleaning. 
NOTE:	 The	CleanView® ProHeat® 
will be fully warmed and will  
provide optimal performance  
after one minute of continuous...

www.bissell.com 
Operations
12
 
1. Turn power switch off.  Remove the 2-in-1 
water tank from the base using the tank 
carry handle. Carry the tank like a bucket to 
a utility sink or outside where you will   
dispose of the collection water. Remove the 
top of the tank by rotating the handle for -
ward to unlatch lid and lifting lid off tank.
2.  Empty collection water from bottom of tank.
3.  After each use, remove and rinse the lint 
screen located on the tank lid. 
4.  If nozzle needs to be cleaned,...

13
Operations
ReadyTools™ continued
5. Vacuum thoroughly to pick up loose 
debris and pet hair. Use a vacuum with 
a brush attachment and a crevice tool to 
clean in fabric folds and tufts.
6.  To begin cleaning with attachments,  
follow the instructions on page 10 for  
filling the 2-in-1 water tank.
7.  Set the ReadyTools dial to the TOOLS setting. 
This will allow spray and suction from the hose. 
8.  Attach the cleaning tool of your choice to 
the end of the hose.
9.  Clean by pressing the spray...

www.bissell.com 
Operations
14
ReadyTools™ continued
Cleaning	with	Deep	 Reach™	 Tool	 
(select models only)
1.  Set tool on soiled surfaces and press the spray 
trigger to spray solution onto the soiled area 
to be cleaned. 
2.  Slowly move the tool back and forth over the 
soiled surface, keeping the tool in contact with 
the carpet. 
Release spray trigger and move tool slow-
ly over the soiled area to suction up water 
and dirt. 
4. Continue to clean the area, working in small 
sections, until no more...

www.bissell.com 15 
Maintenance and care 
Hard Floor Cleaning continued 
8. While pressing the spray trigger, make 
one slow forward wet pass and another 
back.Caution: Do Not Overwet.
9.  Repeat the motion without pressing the 
spray trigger using the hard floor tool to 
squeegee and suction up the dirty water. 
10.  When finished, remove hard floor tool, 
rinse and let dry before storing. Refer 
to the Maintenance and care section on 
page 15 for machine clean up and  
storage instructions.Machine...

www.bissell.com 
Troubleshooting
16Heat	
indicator	 light	does	 not	illuminate
Possible Causes  Remedies
1. The heater switch is not turned on.  1. Turn on the heater switch located on side of unit.
2.   The machine power switch is not turned on.  2.  Both switches must be on to activate the heat   
     indicator light.
Reduced spray OR no spray
Possible cause  Remedies
1.  Bladder may be empty.   1.  Turn power switch off; refill bladder with clean hand hot tap   
   water and formula.
2.  2-in-1 water...

www.bissell.com 17
Troubleshooting
DirtLifter	PowerBrush	 does	not	turn
Possible cause  Remedies1. The brush belt or pump belt is off or broken.  1. Refer to Remedy 4 on page 16 to check if brush belt or   
    pump belt is broken.
Cleaner	 not	picking	 up	solution
Possible cause  Remedies1.  ReadyTools dial may be on the wrong setting  1.  Set ReadyTools dial to either FLOOR CLEANING or TOOLS. 
  for the cleaning job. 
2.   Poor tool position. (Hand held attachments only).  2.  Adjust angle; apply more...

www.bissell.com 
Replacement parts  
Accessories and formulas
18Item 
Part No.  Part Name
 1  203-0104  Tank Assembly Complete
 2  203-0102  Tank Base
 3  203-8114  Removable Nozzle
 4  215-0628  Replacement Pump Belt (with instructions)
 5  015-0621  Replacement Brush Belt (with instructions)
 6  203-0105  Lint Screen
While	not	all	of	these	 parts	may	not	have	 come	 with	your	 machine,	 all	are 	
available	 to	you	 for	purchase,	 if	desired.
Item  Part No.  Part Name
 1 203-0149  Hard Floor Tool
 2...

 This warranty gives you specific legal rights, and you may also have oth\
er rights which may 
vary from country to country. If you need additional instruction regarding this warranty or have 
questions regarding what it may cover, please contact BISSELL Consumer Services by  
telephone, or regular post as described below, or contact your local in country distributor.
Limited Two Year Warranty
 Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, BISSELL Homecare, Inc., 
will replace (with new or...

©2012 BISSELL Homecare, Inc
Grand Rapids, Michigan
All rights reserved. Printed in China
Part Number 120-4414
Rev 9/11
Visit our website at:
www.bissell.com
Scotchgard is a trademark of 3M
Microban
® is a registered trademark 
of Microban Products Company
BISSELL consumer services
www.bissell.com 20
If	 your	 BISSELL	 product	 should	require	 service:Call BISSELL Consumer Services at the numbers below and we will give you the location of a 
BISSELL Authorized Service Center in your area. If you have...