Bisell CleanView Proheat Carpet Cleaner 34T2E User Manual

							www.bissell.com 11
Operations
Carpet cleaning
1. Plug the deep cleaner into a proper 
outlet. Set ReadyTools dial to the FLOOR 
CLEANING setting. Turn the power on 
by pressing the red power switch on 
the back of the unit with your foot. Turn 
heater switch (located on side of unit) 
to the on position. Allow one minute for 
the built-in heater to warm up before 
cleaning. 
NOTE:	 The	CleanView® ProHeat® 
will be fully warmed and will  
provide optimal performance  
after one minute of continuous 
heated	 cleaning.
2. With your foot, press the gray handle 
release lever located on the back of unit 
below water tank to detent handle.
3.  While pressing the spray trigger, make 
one slow forward wet pass and another 
back. Let the built-in heater, BISSELL 2X 
deep cleaning formula and DirtLifter 
PowerBrush do the work for you. 
Caution: Do not overwet.
4.  Release the spray trigger and make one 
slow forward and backward pass over 
the same area to remove any residual 
dirty water and aid in drying.
5.  Repeat cleaning passes until solution  
being suctioned up appears clean. 
Continue passes without pressing the 
spray trigger until you can’t see any 
more water being suctioned up.
Tip:
Thorough vacuuming before deep 
cleaning will prevent early clogging 
of the lint trap.
Handle Release Power Switch
Heater Switch  
						

							www.bissell.com 
Operations
12
 
1. Turn power switch off.  Remove the 2-in-1 
water tank from the base using the tank 
carry handle. Carry the tank like a bucket to 
a utility sink or outside where you will   
dispose of the collection water. Remove the 
top of the tank by rotating the handle for -
ward to unlatch lid and lifting lid off tank.
2.  Empty collection water from bottom of tank.
3.  After each use, remove and rinse the lint 
screen located on the tank lid. 
4.  If nozzle needs to be cleaned, remove by 
grasping handle at the top and pulling   
forward. Clean removable nozzle by   
rinsing under running water.  
5.  When finished, replace nozzle by slightly   
raising front of machine to line up slots on 
the base with the hooks on nozzle. Attach at 
base first and then click nozzle into place. 
NOTE:	 If	nozzle	 is	not	 attached	  
properly loss of suction will occur.
6.  To continue carpet cleaning, refer back to 
pages 10 through 11, beginning with “Fill 
the 2-in-1 water tank” on page 10.
If	 cleaning	 is	complete,	 refer	to	the 	
“Maintenance and care” section on page 15.
ReadyTools™
Your CleanView® ProHeat® comes equipped  
with	 a	hose	 and	at	least	 one	attachment	 for	
cleaning	 stairs,	upholstery,	 and	more.
Important!	 If	using	 the	machine	 to	clean 	
upholstery,	 check	upholstery	 tags.
1. Check manufacturer’s tag before cleaning. 
“W” or “WS” on the tag means you can use 
your deep cleaner. If the tag is coded with “X” 
or “S” (with a diagonal strike through), or says 
“Dry Clean Only,” do not proceed. Do not use 
on velvet or silk. If manufacturer’s tag is missing 
or not coded, check with your furniture dealer. 
2.  Check for colourfastness in an inconspicu-
ous place.
3.  If possible, check upholstery stuffing. Coloured 
stuffing may bleed through fabric when wet.
4.  Plan activities to give upholstery time to 
dry. 
1.
3.
5. 2.
4.
Adsdfdd 
ghg bvh
cvbbj  jkn hnbj  jkvh
gcghh jj  jhffhl kl lgh
Manufacturer’s tag
Empty	 the	2-in-1	 water	tank/clean	 removable	nozzle
Lint Screen  
						

							13
Operations
ReadyTools™ continued
5. Vacuum thoroughly to pick up loose 
debris and pet hair. Use a vacuum with 
a brush attachment and a crevice tool to 
clean in fabric folds and tufts.
6.  To begin cleaning with attachments,  
follow the instructions on page 10 for  
filling the 2-in-1 water tank.
7.  Set the ReadyTools dial to the TOOLS setting. 
This will allow spray and suction from the hose. 
8.  Attach the cleaning tool of your choice to 
the end of the hose.
9.  Clean by pressing the spray trigger to spray  
solution onto the area to be cleaned. Slowly  
move the tool back and forth over the soiled  
surface. Release the spray trigger to suction dirty  
water. Continue to clean in the area, working in  
small sections, until dirt is removed.    
Caution: Do Not Overwet.
10.  When finished cleaning, remove and 
rinse tool(s) in clean, running water.  
11.  It is recommended that you suction clean 
water from the tap to rinse out the hose. 
12.  Before wrapping hose onto tool rack, lift 
end of hose and stretch out to ensure all 
water is cleared from hose.
13.  Wrap flex hose around tool rack.
14.  Empty 2-in-1 water tank and rinse out,  
following instructions on page 12.
15.  If the ReadyTools dial becomes difficult to 
turn, the diverter assembly that holds the 
dial may need to be cleaned. To clean, first 
remove nozzle and locate screw that holds 
the diverter assembly in place. With a Phillips 
screwdriver, remove the screw and set aside.
16.  Remove diverter assembly; hold under running 
water making sure water flows through and 
around the dial. Turn the dial about 10 times 
clockwise and 10 more times counter   
clockwise. This should free up any debris.
17.  Wipe diverter assembly with a soft cloth and 
replace back on machine. Replace nozzle.
18.  Return ReadyTools dial to FLOOR 
CLEANING setting.
7.
11.
15. 12.
16.
Run water through here
Screw  
						

							www.bissell.com 
Operations
14
ReadyTools™ continued
Cleaning	with	Deep	 Reach™	 Tool	 
(select models only)
1.  Set tool on soiled surfaces and press the spray 
trigger to spray solution onto the soiled area 
to be cleaned. 
2.  Slowly move the tool back and forth over the 
soiled surface, keeping the tool in contact with 
the carpet. 
Release spray trigger and move tool slow-
ly over the soiled area to suction up water 
and dirt. 
4. Continue to clean the area, working in small 
sections, until no more dirt can be removed.
Hard Floor Cleaning
Your CleanView® ProHeat®	may	 have	
included	 a	hard	 floor	tool	and	 2X	Hard 	
Floor	 Solutions.	 The	hard	 floor	tool	pro-
vides	 effective	 cleaning	 for	linoleum, 	
vinyl,	 and	tile	floors. 	 
Caution: Do not use on unsealed   
hardwood	 floors.
1.  Thoroughly vacuum or sweep floor to pick 
up any debris.
NOTE: 	Prior	 to	filling	 with	formula 	
and water be sure all carpet cleaning 
formula	 is	thoroughly	 rinsed	from	the	
2-in-1	 water	 tank.
2. Fill BISSELL Hard Floor Solutions to the  
indicated fill line in the built in measuring 
cup and pour into mouth of bladder.
3.  Fill the bladder with clean hand hot tap 
water and set aside.
4.  Attach the hard floor tool to the bottom of 
the machine by hooking it into the nozzle 
and swinging it down until it clicks into 
place. 
5.  Be sure the ReadyTools dial is set to  
FLOOR CLEANING.
6.  Plug into an outlet and turn the power on.
7.  Plan your cleaning route to leave an exit 
path. Be sure to allow adequate time for 
floors to dry. 
4.
1.
3.  
						

							www.bissell.com 15 
Maintenance and care 
Hard Floor Cleaning continued 
8. While pressing the spray trigger, make 
one slow forward wet pass and another 
back.Caution: Do Not Overwet.
9.  Repeat the motion without pressing the 
spray trigger using the hard floor tool to 
squeegee and suction up the dirty water. 
10.  When finished, remove hard floor tool, 
rinse and let dry before storing. Refer 
to the Maintenance and care section on 
page 15 for machine clean up and  
storage instructions.Machine care
For	 best	 results,	 a	few	 simple	 steps	can	
assure	 your	machine	 is	well	 maintained 	
after cleaning is complete.
1.  Turn power switch off. Unplug the 
machine and wrap the power cord. 
2 .  After emptying the 2-in-1 water tank, rinse 
it with running hand hot tap water, tak-
ing care to clean underneath and around 
the heavy duty bladder. Clean out red lint 
screen. Removable nozzle may be rinsed if 
necessary. Refer to page 12.
3.  Replace the 2-in-1 water tank on the 
machine.
4.  Any loose hair or debris can be pulled 
from the brush roll and thrown away.  
5.  To clean attachments, remove from hose and 
rinse in clean, running water. Dry before 
storing. Clean the hose by suctioning clean 
water from the tap. Before wrapping back 
on machine, lift end of hose and stretch out 
to ensure all water is cleared from hose. 
Refer to page 13, illustrations 11 and 12.  
6.  Wipe the machine’s exterior with a soft cloth.
7.  After carpet is dry, vacuum again to 
remove hair and fuzz.
Machine	 storage
Put	the	unit	 away	 in	a	closet	 or	 
basement	 for	the	 next	 use.	Store 	
cleaner	 in	a	protected,	 dry	area.	 Since	
this	 product	 uses	water,	 it	must	 not	be	
stored	 where	 there	is	a	danger	 of	 
freezing. Freezing will damage internal 
components	 and	void	 the	warranty.  
						

							www.bissell.com 
Troubleshooting
16Heat	
indicator	 light	does	 not	illuminate
Possible Causes  Remedies
1. The heater switch is not turned on.  1. Turn on the heater switch located on side of unit.
2.   The machine power switch is not turned on.  2.  Both switches must be on to activate the heat   
     indicator light.
Reduced spray OR no spray
Possible cause  Remedies
1.  Bladder may be empty.   1.  Turn power switch off; refill bladder with clean hand hot tap   
   water and formula.
2.  2-in-1 water tank may not be seated properly.  2. Turn power switch off; remove tank and reseat. 
3.    Pump may have lost prime.  3. Turn power switch off; after 1 minute turn on and depress   
   spray trigger.
4.  The pump belt may be broken.  4. Turn power switch off and unplug from the outlet. To check   
   if a pump belt has broken, you will need a flat head   
   screwdriver. A. Insert the blade end into the slot of the   
   belt access door to release. Examine the belt for breakage.   
   You should be able to see the pump belt looped around   
   the motor shaft. If it is broken or missing, please refer to   
   Replacement Parts on page 18. A replacement belt may be   
   ordered by calling BISSELL Consumer Services. Complete   
   installation instructions will accompany the replacement belt.   
   B. When replacing belt access door be sure to line up slots of   
   belt access door with slots in machine, slide door into place and   
   snap shut.
WARNING:   To reduce the risk of electric 
shock, or injury, unplug from the 
outlet before servcing
Slots
A .
B.
Pump Belt  
						

							www.bissell.com 17
Troubleshooting
DirtLifter	PowerBrush	 does	not	turn
Possible cause  Remedies1. The brush belt or pump belt is off or broken.  1. Refer to Remedy 4 on page 16 to check if brush belt or   
    pump belt is broken.
Cleaner	 not	picking	 up	solution
Possible cause  Remedies1.  ReadyTools dial may be on the wrong setting  1.  Set ReadyTools dial to either FLOOR CLEANING or TOOLS. 
  for the cleaning job. 
2.   Poor tool position. (Hand held attachments only).  2.  Adjust angle; apply more downward pressure.
3.   Removable nozzle may not be properly attached.  3.  Make sure nozzle is on correctly by slightly raising front   
   of machine to line up slots on the base of the machine   
   with the hooks on nozzle. Attach at base first and   
   then click nozzle into place. Refer to image 5 on page 12.
4.  2-in-1 water tank lid is not properly installed.  4. Re-install lid; refer to the images on page 10. 
5.  2-in-1 water tank is not properly seated.  5. 2-in-1 water tank must be firmly seated to function; remove   
   and reseat 2-in-1 water tank. 
6.  2-in-1 water tank has picked up maximum dirty water.  6. Empty 2-in-1 water tank and refill, refer to the Operation   
   section.
7.  The lint screen may be clogged.  7. Clean out lint screen. Refer to page 12.
Other	 maintenance	 or	service	 not	included	 in	the	 manual	 should	be	 
performed	 by	an	 authorized	 service	representative.
Thank	you	for	selecting	 a	BISSELL	 product.
Please	do	not	 return	 this	product	 to	the	 store.               
						

							www.bissell.com 
Replacement parts  
Accessories and formulas
18Item 
Part No.  Part Name
 1  203-0104  Tank Assembly Complete
 2  203-0102  Tank Base
 3  203-8114  Removable Nozzle
 4  215-0628  Replacement Pump Belt (with instructions)
 5  015-0621  Replacement Brush Belt (with instructions)
 6  203-0105  Lint Screen
While	not	all	of	these	 parts	may	not	have	 come	 with	your	 machine,	 all	are 	
available	 to	you	 for	purchase,	 if	desired.
Item  Part No.  Part Name
 1 203-0149  Hard Floor Tool
 2  203-6651  3" Tough Stain Tool
 3  203-6653  4" Upholstery Tool
 4  203-6654  6" Stair Tool
 5  203-6652  Powered TurboBrush ™
 Hand Tool
 6  203-0116  Spraying 2-in-1 Crevice Tool w/Brush
 7  203-6655  Spraying Crevice Tool
 8  203-8113  Deep Reach
™ Tool  
 9  210-3040  Mesh Tool Storage Bag
10  81L5-E  1.5 L 2X Wash & Protect Professional Formula w/ Scotchgard
™ Protector
11   66W9-E  1.5 L 2X Wash & Protect Pet Stain & Odour Formula w/ Scotchgard ™
 Protector
12  92F4-E  1.5 L 2X Wash & Protect Fresh Fragrance Formula w/ Scotchgard ™
 Protector
1 3  12W4-E  1.5 L 2X Wash & Protect Spring Breeze Fragrance Formula w/   
   Scotchgard™
 Protector
14  33D2-E  1.5 L 2X Wash & Protect Lavender Fragrance Formula w/ Scotchgard ™
 Protector
15  56L9-E  473 mL 2X Hard Floor Solutions 
16  0400-E  651 mL Tough Stain Precleaner
  
1 23456
1
6
13
2
7 8
14
3
9
15
4
11
16
5
12
10
Note: Additional BISSELL formula options may be available at your local \
retailer.  
						

							 This warranty gives you specific legal rights, and you may also have oth\
er rights which may 
vary from country to country. If you need additional instruction regarding this warranty or have 
questions regarding what it may cover, please contact BISSELL Consumer Services by  
telephone, or regular post as described below, or contact your local in country distributor.
Limited Two Year Warranty
 Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, BISSELL Homecare, Inc., 
will replace (with new or remanufactured components), at BISSELL’s option, free of charge 
from the date of purchase by the original purchaser, for two years any defective or   
malfunctioning part do to manufacturers defect. 
  This warranty applies to product used for personal, and not commercial o\
r rental service. This 
warranty does not apply to fans or routine maintenance components such a\
s filters, belts, or 
brushes. Damage or malfunction caused by negligence, abuse, or use not i\
n accordance with 
the User’s Guide is not covered.
BISSELL HOMECARE INC. IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL   
DAMAGES OF ANY NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT.   
BISSELL’S LIABILITY WILL NOT EXCEED THE PURCHASE PRICE OF THE PRODUCT. 
*EXCEPTIONS	 AND	EXCLUSIONS	 FROM	THE	TERMS	 OF	THE	 LIMITED	 WARRANTY
THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES EITHER ORAL OR 
WRITTEN. ANY IMPLIED WARRANTIES WHICH MAY ARISE BY OPERATION OF LAW, INCLUDING 
THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE 
LIMITED TO THE TWO YEAR DURATION FROM THE DATE OF PURCHASE AS DESCRIBED ABOVE.
www.bissell.com 
19
Warranty - BISSELL CleanView® ProHeat®
For UK inquiries:
Monday - Thursday     9 am — 5 pm 
Friday      9 am — 4 pm 
BISSELL Homecare (Overseas)  
Ground Floor  
226 Berwick Avenue  
Slough  
Berkshire, SL1 4QT  
United Kingdom 
Telephone: 0844-888-6644  For	
all	other	 inquiries:
Monday - Friday     8 am — 4 pm 
BISSELL	 Homecare,	 Inc.
PO Box 1888
Grand Rapids, Michigan 49501 USA
Telephone: 01-616-453-4451  
Fax: 01-616-453-1383
Note: Additional BISSELL formula options may be available at your local \
retailer.  
						

							©2012 BISSELL Homecare, Inc
Grand Rapids, Michigan
All rights reserved. Printed in China
Part Number 120-4414
Rev 9/11
Visit our website at:
www.bissell.com
Scotchgard is a trademark of 3M
Microban
® is a registered trademark 
of Microban Products Company
BISSELL consumer services
www.bissell.com 20
If	 your	 BISSELL	 product	 should	require	 service:Call BISSELL Consumer Services at the numbers below and we will give you the location of a 
BISSELL Authorized Service Center in your area. If you have questions about your warranty or 
need replacement parts please contact the numbers below.
Or visit the BISSELL website -  www.bissell.com
When contacting BISSELL, have model number of cleaner available.
Please record your Model Number: ___________________
Please record your Purchase Date:  ___________________
NOTE:	Please	 keep	your	original	 sales	receipt.	 It	 
provides	 proof	of	purchase	 date	in	the	 event	 of	a	 
warranty claim. See Warranty on page 19 for details.  
For UK inquiries:
Monday - Thursday     9 am — 5 pm 
Friday      9 am — 4 pm 
BISSELL Homecare (Overseas)  
Ground Floor  
226 Berwick Avenue  
Slough  
Berkshire, SL1 4QT   
United Kingdom 
Telephone: 0844-888-6644 For	
all	other	 inquiries:
Monday - Friday     8 am — 4 pm 
BISSELL	 Homecare,	 Inc.
PO Box 1888
Grand Rapids, Michigan 49501 USA
Telephone: 01-616-453-4451  
Fax: 01-616-453-1383