Bisell CleanView LiftOff 10N4E User Manual

							www.bissell.com 11
Operations
Portable spot cleaning mode
Preparing the machine
1. Step on the portable spot cleaning pedal to 
release the portable spot cleaner.  
2.  Release flex hose by twisting the hose 
secure latch clockwise. Unwrap flex 
hose completely. 
3.  Attach the desired tool to the hose grip 
until it snaps together. Make certain the 
tool is securely attached. 
4.  Twist the Quick Release cord wrap clock-
wise to unwrap the power cord com-
pletely and plug into grounded outlet.
Filling tank
1. Follow the instructions for filling the tank 
in the upright cleaning mode section on 
page 8
Cleaning with Tools:
IMPORTANT! If using to clean uphol-
stery, check upholstery tags. Check 
manufacturer’s tag before cleaning. 
“W” or “WS” on the tag means you 
can use your CleanView
® Lift-Off® if 
the tag is coded with an “X” or an 
“S”(with a diagonal stripe through it), 
or says “Dry Clean Only”, do not pro-
ceed with any deep cleaning machine. 
Do not use on velvet or silk. If manu-
facturer’s tag is missing or not coded, 
check with your furniture dealer.”)
1.  Hold the tool approximately 2.5 cm 
above the soiled surface. Press the 
spray trigger to apply the cleaning solu-
tion to the soiled area. 
 
Note: Hold end of hose below the 
tank water level to help prime the 
portable spot cleaner.
2.  Using the brush on the tool, gently scrub the 
area to be cleaned. 
3.  Apply downward pressure on the tool and 
pull it toward you. The suction will remove 
the dirt and cleaning solution. Continue until 
no more dirt can be removed. 
Adsdfdd  ghg bvh
cvbbj  jkn hnbj  jkvh
gcghh jj  jhffhl kl lgh
Manufacturer’s tag
IMPORTANT   
Check for colourfastness in an 
inconspicuous place. If pos-
sible, check upholstery stuffing. 
Coloured stuffing may bleed 
through fabric  
						

							www.bissell.com 
Operations 
12
Cleaning with Deep Reach™ Tool 
(select models only)
1.  Set tool on soiled surfaces and press the 
spray trigger to spray solution onto the 
soiled area to be cleaned. 
2.  Slowly move the tool back and forth over 
the soiled surface, keeping the tool in con-
tact with the carpet. 
Release spray trigger and move tool 
slowly over the soiled area to suction up 
water and dirt. 
4. Continue to clean the area, working in 
small sections, until no more dirt can be 
removed.
Empty dirty tank
Follow the instructions under Empty 
dirty tank section on page 9 of the 
Upright cleaning mode section. 
Replacing portable machine on base
1. Align the product as the graphic shows, 
with the cord side on the left and hose 
side on the right. 
2.  Push down the portable spot cleaner 
until you hear it click securely into 
place. Test the fit by pulling up on the 
carry handle to make sure it is secure.
Cleaning portable machine 
1. Remove and rinse the tools in clean, run-
ning water. Dry and replace in the tool 
storage provided.
2.   It is recommended that you suction clean 
water from a bowl to rinse out the hose. 
Then lift end of hose and stretch out to 
ensure all water is cleared from hose. 
3.  Coil flex hose around the hose wrap 
and secure with latch.
4.  Check suction gate and if it appears 
dirty, follow steps 1-4 under Cleaning 
Suction Gate on page 13.
1.
3.
Portable spot cleaning mode continued
graphic
1.  
						

							www.bissell.com www.bissell.com 13
Maintenance and care  
Machine care (check regularly)
Cleaning suction gate
The suction gate automatically diverts 
air when the portable deep cleaner 
is detached. This should be checked 
and cleaned regularly for any dirt and 
debris.
1. Step on the pedal and remove the 
portable spot cleaner. Remove dirty 
tank.
2.  Remove two screws and pull off   
suction gate door.
3.  Wipe suction gate clean and rinse  
suction gate door.
4.  Replace suction gate door and two 
screws.
Cleaning spray tips
1. Step on the pedal and remove the 
portable spot cleaner. To remove, push 
in tab and pull it out. 
2.  Clean by rinsing under water. 
3.  Replace by snapping back in. 
4.  Repeat steps on second spray tip.
Cleaning solution filter
1. Step on the pedal and remove the   
portable spot cleaner. Remove the red 
solution filter cap on the base of the 
machine by inserting a coin or a flat 
head screw driver into the slot on the 
top. 
2.  Turn counter clockwise to unscrew. Set 
aside.
3.  Remove the white filter by the post. 
Rinse the filter under water.
4.  Replace the white filter back into the 
filter area. 
Note: Make sure the white filter 
is seated properly before replac-
ing the red solution filter cap.
5. Replace the red solution filter cap and 
turn clockwise to tighten.
Solution  
Filter CapSuction 
gate
Filter
2.
3.
5.
Spray 
Tips
1. 2.
WARNING:
  To reduce the risk of fire, elec-
tric shock, or injury, turn power   
OFF and disconnect plug from 
electrical outlet before perform-
ing maintenance or trouble-
shooting.  
						

							www.bissell.com 
Maintenance and care  
14
Occasional replacement of one or 
both belts may become necessary. 
If that is needed, please follow the 
instructions below.
1.  Turn off the machine, and unplug it from   
the outlet. Remove portable spot cleaner.
2.  Remove the nozzle by unscrewing three 
screws on the nozzle cover.
3.  Turn the machine on its side.  
IMPORTANT: with portable spot 
cleaning pedal facing down.
4.  Remove end cap by unscrewing the 
3 screws. Take care not to drop the 
screws into the unit.
5.  Remove 1 silver screw from the pivot 
arm.
6.  Remove pivot arm by gently lifting up.
7.  Remove small brush belt.
8.  Replace small brush belt, and reverse   
steps above.
9.  Manually rotate brushes by hand to make 
sure they move freely. May notice a slight  
resistance from the motor.
2.
4.
6. 8.
Small belt removal and replacement (as needed)
7.
5.
WARNING:  To reduce the risk of fire, 
electric shock or injury, 
unplug from the outlet 
before servicing.  
						

							www.bissell.com 15
Maintenance and care  
 
Brushes can be removed for cleaning 
or replacement as needed. 
1. Follow small belt removal Instructions on   
page 14 items 1-7.
2.  Remove brush rolls by pulling them off 
of the metal rods. Be careful not to 
lose the small washer at each 
end of the brush rolls.
3.  Re-attach the large belt to the grooves 
on the end of the new brush rolls. If the 
belt is damaged, replace with a new 
belt.
4.  Place cleaned or new brush rolls back 
onto the rods. Make sure one washer is 
on each end of the rollers prior to sliding 
onto the rod. Be sure the brush is seated 
completely on the rod.
5.  Replace small belt over grooves in back 
roller and metal cog.
6.  Replace pivot arm and secure with silver 
screw.
7.  Re-attach end cap by tightening with the 
(3) black screws.
8.  Return front nozzle to front of unit, by 
latching from underneath and then 
securing with 3 screws.
9.  Follow step number 8 & 9 on page 14.
  If you have any questions or are having   
trouble installing or replacing your 
belt(s) or brushes, please call  
BISSELL Consumer Services.
2.
4.
6.
8. 3.
5.
7.
Brush removal and large belt replacement (as needed)
WARNING:   To reduce the risk of fire, 
electric shock or injury, 
unplug from the outlet 
before servicing.  
						

							www.bissell.com 
Troubleshooting 
16Built-in heater ready light does not illuminate
Possible causes 
Remedies
1.  The power is not turned ON    1.  The power must be ON to activate the heater ready light
2.   The portable spot cleaner is not attached completely  2.  Make sure the portable spot cleaner is attached   
    Push down firmly to check
Reduced Spray or No Spray
Possible causes  Remedies
1.  Formula & water tank may be empty  1.  Refill tank
2.  Formula & water tank may not be seated completely  2. Turn power OFF. Remove and reseat tank
3.  Pump may have lost prime in portable spot cleaning mode  3. Hold end of hose below water level in tank to prime
4.   The portable spot cleaner is not attached completely  4.  Push down firmly to check connection
5.   Solution filter may be clogged   5.  Follow steps under cleaning filter on page 13
DirtLifter™ PowerBrush does not turn
Possible causes  Remedies
1.  The portable spot cleaner is not attached completely  1.  Make sure the portable spot cleaner is attached.   
    Push down firmly to check
2.   The unit is in the upright position  2.  Brushes only rotate when unit is reclined using the   
    recline  pedal
3.  Circuit breaker on machine (if equipped)  may have tripped  
3.  Turn the machine OFF and unplug from outlet. Check   
    to see if foreign object is caught in brush roll. Remove   
    object. Plug machine in to reset circuit breaker
4.  The belt is off or broken  4. Turn power OFF and unplug unit from outlet. Follow   
    instructions on pages 14 and 15
Loss of suction power
Possible causes  Remedies
1.  Tanks may not be seated properly  1.  Pick up both tanks and reseat them so it they fit snugly on   
    the  unit 
2.   Nozzles may not be assembled properly  2.  Unplug the unit. Check to make sure the "lip" of the   
    nozzle is securely hooked into the groove on bottom of   
    Tank (see page 10)
3.   The portable spot cleaner is not attached completely  3.  Make sure the portable spot cleaner is attached.   
    Push down firmly to check
4.   Dirty tank has picked up maximum amount of  4.  Empty dirty tank   
  dirty water and has reached full line    
5.   Formula & water tank is empty   5.  Check fluid levels in formula & water tank 
6.  Suction gate is open  6. Check to make sure the suction gate is closed. Follow   
    “Cleaning suction gate” instructions on page 13
Other maintenance or service not included in the manual should be   
performed by an authorized service representative.
Thank you for selecting a BISSELL product.
Please do not return this product to the store.               
						

							www.bissell.com 17
Accessories & formulas
Item Part No.  Part Name 1 203-6651  3” Tough Stain Tool
 2  203-6652  Powered TurboBrush™ Hand Tool
 3  203-6653  4” Upholstery Tool
 4  203-6654  6” Stair Tool
 5  203-7885  Spraying Crevice Tool 
 6   203-8113  Deep Reach™ Tool
 7  310-3040  Mesh Bag
 8   81L5-E  1.5 L 2X Wash & Protect Professional Formula w/ Scotchgard™ Protector
 9   66W9-E  1.5 L 2X Wash & Protect Pet Stain & Odour Formula w/ Scotchgard ™
 Protector
10  92F4-E  1.5 L 2X Wash & Protect Fresh Fragrance Formula w/ Scotchgard ™
 Protector
1 1  12W4-E  1.5 L 2X Wash & Protect Spring Breeze Fragrance Formula w/   
     Scotchgard™
 Protector
12  33D2-E  1.5 L 2X Wash & Protect Lavender Fragrance Formula w/ Scotchgard ™
 Protector
13  0400-E  651 mL Tough Stain Precleaner
*Not all parts are included with every model.
1
6
13 
2
345
117
8
12 9
10
Note: Additional BISSELL formula options may be available at your local \
retailer.  
						

							Below please find a list of common replacement parts. While not all of these 
parts may have come with your specific machine, all are available to you fo\
r 
purchase, if desired.
Item Part No.  Part Name
1 203-7893  Formula & Water Tank Assembly (includes cap and insert)
2.  203-6675  Cap and Insert for Formula & Water Tank
3.  203-8102  Dirty Tank Assembly (includes entire tank)
4.  203-7904  Cord Wrap
5.  203-7896  End Caps with Edge Brushes (2 pack, includes screws)
6.  203-7897  Spray Tips Assembly (includes two spray tips)
7.  203-7898  In-line Filter Assembly (includes cap and filter)
8.  203-7901  Nozzle Gasket
9.   203-8103  Nozzle Cover Assembly (includes gasket, nozzle cover, and front nozzle cover)
10.  203-8104  Front Nozzle 
11.  203-8105  Brush Assembly (includes 2 brush rolls, 2 axles, and 2 swivel arms)
12.  203-8106  Brush Single Pack (includes 1 brush roll, and 1 axle)
13.  203-7900  Small Brush Belt
14.  203-7899  Large Brush Belt
15.  203-6689  Hose Secure Latch 
16.  203-7918  Dirty Tank Gasket Assembly (include both gaskets
)
17.  203-7917  Diverter Cover Assembly (includes cover and screws)
*Not all parts are included with every model.
www.bissell.com 18
Replacement parts  
1
6
11
16
2
7 12
17
3
8
13 4
9
14 5
10
15  
						

							www.bissell.com 19
Warranty - BISSELL CleanView® Lift-Off®
 This warranty gives you specific legal rights, and you may also have oth\
er rights which may 
vary from country to country. If you need additional instruction regarding this warranty or have 
questions regarding what it may cover, please contact BISSELL Consumer Services by  
telephone, or regular post as described below, or contact your local in country distributor.
Limited Five Year Warranty
 Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, BISSELL Homecare, Inc., 
will replace (with new or remanufactured components), at BISSELL’s option, free of charge 
from the date of purchase by the original purchaser, for five years any defective or   
malfunctioning part do to manufacturers defect. 
  This warranty applies to product used for personal, and not commercial o\
r rental service. This 
warranty does not apply to fans or routine maintenance components such a\
s filters, belts, or 
brushes. Damage or malfunction caused by negligence, abuse, or use not i\
n accordance with 
the User’s Guide is not covered.
BISSELL HOMECARE INC. IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL   
DAMAGES OF ANY NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT.   
BISSELL’S LIABILITY WILL NOT EXCEED THE PURCHASE PRICE OF THE PRODUCT. 
*EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY
THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES EITHER ORAL OR 
WRITTEN. ANY IMPLIED WARRANTIES WHICH MAY ARISE BY OPERATION OF LAW, INCLUDING 
THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE 
LIMITED TO THE FIVE YEAR DURATION FROM THE DATE OF PURCHASE AS DESCRIBED ABOVE.
For UK inquiries:
Monday - Thursday     9 am — 5 pm 
Friday      9 am — 4 pm 
BISSELL Homecare (Overseas) Inc.  
Ground Floor 
226 Berwick Avenue 
Slough 
Berkshire SL1 4QT 
United Kingdom 
Telephone:  0844-888-6644 For all other inquiries:
Monday - Friday 
   8 am — 4 pm 
BISSELL Homecare, Inc.
PO Box 1888
Grand Rapids, Michigan 49501 USA
Telephone: 01-616-453-4451  
Fax: 01-616-453-1383  
						

							BISSELL consumer services
©2012 BISSELL Homecare, Inc
Grand Rapids, Michigan
All rights reserved. Printed in China
Part Number 120-4421
Rev 10/11
Visit our website at:
www.bissell.com
Scotchgard is a trademark of 3M
Microban
® is a registered trademark 
of Microban Products Company
www.bissell.com 20
If your BISSELL product should require service:Call BISSELL Consumer Services at the numbers below and we will give you the location of a 
BISSELL Authorized Service Center in your area. If you have questions about your warranty or 
need replacement parts please contact the numbers below.
Or visit the BISSELL website -  www.bissell.com
When contacting BISSELL, have model number of cleaner available.
Please record your Model Number: ___________________
Please record your Purchase Date:  ___________________
NOTE: Please keep your original sales receipt. It  
provides proof of purchase date in the event of a  
warranty claim. See Warranty on page 19 for details.  
For UK inquiries:
Monday - Thursday    9 am — 5 pm 
Friday      9 am — 4 pm 
BISSELL Homecare (Overseas) Inc.  
Ground Floor  
226 Berwick Avenue  
Slough  
Berkshire SL1 4QT  
United Kingdom  
Telephone:  0844-888-6644 For all other inquiries:
Monday - Friday 
   8 am — 4 pm 
BISSELL Homecare, Inc.
PO Box 1888
Grand Rapids, Michigan 49501 USA
Telephone: 01-616-453-4451  
Fax: 01-616-453-1383