Bisell CleanView Deep Clean Carpet Cleaner 18Z7E User Manual

www.bissell.com 11
Operations
Carpet cleaning continued
6. Plug into a proper outlet and turn the power 
and heater switches to the ON ( I ) posi-
tion. Allow 1 minute for the built-in heater to 
warm-up before cleaning. The CleanView
® 
Deep Clean will be fully warmed and will 
provide optimal performance after a minute 
of  continuous heated cleaning.
7.  Cleaning Strokes. While pressing the trig-
ger, make one slow forward wet pass and 
another one back. Caution: Do not 
overwet. Take care not to run...

www.bissell.com 
Operations
12
Carpet cleaning continued
8c. Lift the bottom portion of the tank; pour out 
dirty water in the sink through the triangular 
shaped opening in the corner of the tank.
Note: You may notice hair & debris 
deposits on the carpet or in the tank 
that were loosened by the cleaning 
action. This debris should be picked 
up and thrown away.
8d.  Fill the heavy duty bladder with clean 
hand hot tap water, following instructions 
1c through 1e on page 10.
Note: Remember to secure...

www.bissell.com 13
Operations
Cleaning with attachments
Your CleanView® Deep Clean machine 
comes equipped with a hose and at 
least one attachment for cleaning 
stairs, upholstery, and more.
1. Important! If using to clean uphol- stery, check upholstery tags. 
A.  Check manufacturer’s tag before clean-
ing. “W” or “WS” on the tag means 
you can use your deep cleaner. If the 
tag is coded with an “X” or an “S” 
(with a diagonal stripe through it), or 
says “Dry Clean Only”, do not proceed 
with any deep...

www.bissell.com 
Operations
14
 
8. Remove and rinse tools in clean, running 
water. Dry and replace in the tool caddy.
9.  It is recommended that you suction clean 
water from a bowl to rinse out the hose. 
10.  Before replacing lift end of hose and 
stretch out to ensure all water is cleared 
from hose.
11.  Coil flex hose around the tool caddy.
12.  Empty 2-in-1 water tank and rinse out,  
following the instructions on pages 11 
through 12.  
13.  Return ReadyTools dial to floor setting.
Cleaning with...

www.bissell.com 15
Operations
Stain removal
Do Not Delay! Attending to an  
accident soon after it occurs ensures 
the most optimal clean. Leaving it 
for an extended period of time may 
cause it to set and become  
permanent.
1. Blot up liquids with an absorbent cloth or 
paper towels. White materials are recom-
mended because certain dyes may bleed 
and make the stain worse.
2.  Gently scrape up any semi-solids with a 
spoon or spatula. Do not use a knife or other 
utensil with sharp edges because it...

www.bissell.com 
Operations
16
Hard floor cleaning
Your CleanView® Deep Clean model 
may have come with a hard floor tool 
and 2X Hard Floor Solutions Formula. 
The hard floor tool provides effective 
cleaning for linoleum, vinyl, and tile 
floors. 
Caution: Do not use on unsealed   
hardwood floors.
1.  Vacuum or sweep thoroughly to pick up 
any loose debris and pet hair.
2.  Move any furniture, if needed.
3.  Fill the formula tank to "WATER" line 
with water. Fill to "FORMULA" line with...

www.bissell.com 17
Maintenance and care  
Machine storage
Once your cleaning is complete, 
make sure the 2-in-1 water tank is 
emptied, rinsed out, and dried before 
the next use. The formula tank can 
remain filled and ready to go.
Note: Store cleaner in a protected, 
dry area. Since this product uses 
water, it must not be stored where 
there is a danger of freezing. 
Freezing will damage internal  
components and void the warranty.
Machine care
For best results, a few simple steps can 
assure your...

www.bissell.com 
Maintenance and care  
18
Machine care continued
6.  The inside of the end caps by the brush 
rolls can be wiped out with a clean paper 
towel, or, if a more thorough cleaning is 
desired, the end caps can be taken off 
using a Phillips head screwdriver and 
rinsed clean. Replace after cleaning.
7.  Any loose hair or debris can be pulled from 
the brush rolls and thrown away. For the 
most thorough clean before storage, follow 
directions on pages 18 & 19 for removal 
and replacement of...

www.bissell.com 19
Maintenance and care   
 
Brushes can be removed for cleaning 
or replacement as needed. 
1. Follow small belt removal Instructions on   
page 18.
2.  Remove brush rolls by pulling them off 
of the metal rods.
3.  Place cleaned or new brush rolls back 
onto the rods. Make sure one washer is 
on each end of the rollers prior to sliding 
onto the rod. Be sure to let the rod slide 
through the bushing to insure proper fit.
4.  Re-attach the long belt on the bottom to 
the cogs of the...

www.bissell.com 
Troubleshooting
20Built-in heater ready light does not illuminate
Possible causes 
Remedies
1.  The heater switch is not turned ON ( I )  1.  Turn the heater switch ON ( I )
2.   The power switch is not turned ON ( I )  2.  Both switches must be ON ( I ) to activate the   
    heater ready light
Reduce Spray or No Spray
Possible causes  Remedies
1.  Water tank may be empty   1.  Fill heavy duty bladder with hot tap water
2.   Formula tank may be empty   2.  Fill formula tank with BISSELL...