Bisell Cleanview Bagless Power Trak 3593E User Manual

							You should check your vacuum cleaner’s Rotating 
Floor Brush and Drive Belt regularly for wear or 
damage. You should also clean the brush and brush 
ends of strings, hair, and carpet fibers. These can 
wrap around the brush and hamper its ability to 
effectively clean your carpet. Also remove any 
debris that has accumulated under the brush cover.
Unplug cleaner from electrical outlet.
Place handle in Low position and turn vacuum cleaner 
over so bottom side is up.
Remove the five screws as shown with a Screwdriver. 
Lift the Brush Cover off. 
Grasp Rotating Floor Brush at both ends and lift.
Clean strings, hair and other debris from Rotating Floor 
Brush, paying particular attention to brush ends.
Clean strings, hair and other debris from Motor Pulley and 
Drive Belt areas.
Check Drive Belt carefully for wear, cuts or stressed areas.
Check Air Passageway for obstructions. Remove debris 
from this area.
Use only BISSELL Style 7 Replacement Belts in your 
CleanView Bagless Power Trak Plus.
Unplug cleaner from electrical outlet.
With Rotating Floor Brush removed from vacuum cleaner 
(Steps 1-4 of check Rotating Floor Brush and Drive Belt), 
grasp old Drive Belt and remove from Motor Pulley. 
Discard old Drive Belt.
Place new Drive Belt over Motor Pulley and stretch other end 
over Rotating Floor Brush in the space between the bristles.
Place ends of Rotating Floor Brush down into slots on 
sides as shown.
Turn Rotating Floor Brush by hand several times in the 
direction of Motor Pulley. If properly installed, Drive Belt 
will center itself on Rotating Brush crown.
Reposition Brush Cover and screw or snap back into place. 
Check to be sure all screws are secure.
11
1.
2.
 WARNING: To reduce the risk of injury 
from moving parts, turn 
off vacuum cleaner and 
disconnect Power Plug 
from electrical outlet.
3.
Replace Drive Belt
Check Rotating Floor Brush and Drive Belt 
1.
2.
3.
4.
5.
6.
4.
5.
6.
7.
8.
Air Passageway
Motor PulleyWide Power Trak foot 
						

							12
The TurboBrush should be checked regularly for clogs 
or debris wrapping around the brush roll.
Unplug vacuum from electrical outlet.
If a clog is present or debris is visible, unscrew the two 
screws on the back of the TurboBrush to remove the 
faceplate and clear any obstructions.
To clean debris from the brush roll, remove the screw 
located by the brush roll with a Phillips head screwdriver. 
Lift the belt cover. Remove the brush roll from the drive 
belt and clean debris.
Reposition the drive belt on the brush roll. Place ends 
of brush roll in slots on sides as shown. Reposition belt 
cover and secure with one screw. Reposition faceplate 
and secure with two screws. 
Low suction or poor pickup may be due to a clog in 
the vacuum cleaner. If you notice a change in the 
sound of the motor or a reduction in the spinning 
action, check for clogs.
Unplug cleaner from electrical outlet.
Empty Dirt Container.
Check Upper Tank for build up or clogs.
Remove the Upper Tank and check the suction inlet for a clog.
Grasp the Quick Reach Handle and lift Hose Wand to 
separate from the suction opening. Check for a clogs in 
the Base and the Wand.
Remove the Twist n Snap Hose from the vacuum by 
turning to the left. Check for clog in the suction Inlet 
and hose. Straighten the hose and unclog with a long, 
narrow object.
Remove the screw attaching the Hose Wand Base to the 
vacuum. Straighten the Hose Wand Base and unclog with 
long, narrow object.
If the clog persists, follow the instructions for Checking 
the Rotating Floor Brush on page 11 and inspect the Air 
Passageway for obstructions.
Maintaining TurboBrush
Suction 
Inlet
Air Passageway
4.
5.
7.
8.
1.
2.
3.
Hose Wand 
Base
Clearing Clogs 
1.
2.
4.
3.
6. 
						

							13
Troubleshooting
Vacuum cleaner won’t run
Possible Causes Remedies
  Power cord not plugged in    Check electrical plug
Vacuum cleaner or Tools won’t pick up dirt
Possible Causes Remedies
  Incorrect Height Adjustment    Adjust Powerfoot to correct height setting
  Hose not attached to suction opening    Grasp Quick Reach Handle and firmly push Hose 
      Wand onto the suction opening
  Twist ‘n Snap Hose not securely attached    Make sure Twist ‘n Snap Hose is snapped into 
    locked position
  Crack or hole in Hose    Check Hose and replace if needed
  Broken or worn Drive Belt    Replace Drive Belt, see page 11
  Rotating Floor Brush bristles worn    Replace brush
  Rotating Floor Brush jammed   Remove brush and clean debris from brush ends
  Clog in vacuum   Clear clog, see page 12 
  Dirt Container full    Empty Dirt Container
  Dirt Container or Upper Tank not installed properly    Position correctly and lock in place
  Filters are dirty    Check and clean Upper Tank, 
      Pre-Motor and Post-Motor Filters
Vacuum cleaner is difficult to push
Possible Causes  Remedies
  Incorrect Height Adjustment    Adjust Powerfoot to correct height setting
Visible dirt escaping from cleaner
Possible Causes  Remedies
  Dirt Container full    Empty Dirt Container
  Filters missing or installed incorrectly    Check Upper Tank, Pre-Motor and Post-Motor
      Filters for correct installation
  Dirt Container installed incorrectly    Pull out and re-insert Dirt Container correctly 
If suggested solutions for this or any function of the CleanView Bagless Power Trak Plus 
do not correct the problem, call BISSELL Consumer Services.
11
11
22
33
99
7
88
44
55
66
1010
 WARNING: To reduce the risk of injury from 
moving parts and/ or electrical 
shock, turn Power Switch OFF 
and disconnect plug from electrical 
outlet before performing 
troubleshooting checks.
1111
7
11
22
33
11 
						

							14
BISSELL Consumer Services
If your BISSELL product should require service:
 In the UK call BISSELL Consumer Services at the number below and we will give you the location 
of a BISSELL Authorized Service Center in your area. For all other countries contact your local in 
country distributor for questions, service, or repair. 
If you have questions about your warranty or need replacement parts please contact 
the numbers below.
For UK inquiries:
Monday - Thursday  9 am — 5 pm
  Friday  9 am — 4 pm
BISSELL Homecare (Overseas) Inc.
The Boat Yard 
105 Straight Road
Old Windsor
Berkshire, SL4 2SE
United Kingdom
Telephone: 0870-225-0109 
For Australian inquiries:
24 hours a day 7 days a week
E.D. Oates Pty Ltd
76 - 82 Newlands Road
Reservoir VIC 3073
Australia
Telephone: 1-800-811-183
For all other inquiries:
Monday - Friday    8 am — 4 pm 
BISSELL Homec are, Inc.
PO Box 1888
Grand Rapids, Michigan 49501 USA
Telephone: 01-616-453-4451
Fax: 01-616-453-1383
Or visit the BISSELL website - www.bissell.com
When contacting BISSELL, have model number of unit available.
Please record your Model Number: ___________________
Please record your Purchase Date: ___________________
NOTE: Please keep your original sales receipt. It provides proof of date of 
purchase in the event of a warranty claim. See About Your Warranty 
on page 16 for details.
Please do not return this product to the store. 
						

							15
Replacement Parts – BISSELL CleanView Power Trak Plus
Item  Part No.  Part Name
 1  32074  Style 7/9/10 Drive Belt - 2 Pack
 2    203-1063   Crevice Tool
 3    203-1228   Dusting Brush/Upholstery Tool 
 4    203-1227   TurboBrush 
 5    203-6624  Stair Cleaning Tool (Optional Item)
 6    203-1084   Extension Wand
 7    203-2035  Wire Reinforced Twist ‘n Snap Vacuum Hose Clear
 8    203-1128  Hose Collar with Screws 
 9    203-2013   Wide Power Trak Foot Brush Roll 
10   3093  Style 7/8 Upper Tank Filter and Pre-Motor Filter Set
11   3099  Style 7 Post-Motor Filter Set - 2 pack (Optional Item)
12   32076  Style 7 HEPA Media Post-Motor Filter  
12345
678910
1112 
						

							Warranty
16
  This warranty gives you specific legal rights, and you may also have other rights which may vary 
from country to country. If you need additional instruction regarding this warranty or have questions 
regarding what it may cover, please contact BISSELL Consumer Services by telephone, or regular post as 
described below, or contact your local in country distributor.
  Limited Two Year Warranty
 Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, BISSELL Homecare, Inc., will replace (with new 
or remanufactured components), at BISSELL’s option, free of charge from the date of purchase by the original 
purchaser, for two years any defective or malfunctioning part do to manufacturers defect. 
  This warranty applies to product used for personal, and not commercial or rental service. This warranty does 
not apply to fans or routine maintenance components such as filters, belts, or brushes. Damage or malfunction 
caused by negligence, abuse, or use not in accordance with the User’s Guide is not covered.
For UK inquiries:
Monday - Thursday    9 am — 5 pm 
Friday      9 am — 4 pm 
BISSELL Homecare (Overseas) Inc.
The Boat Yard 
105 Straight Road 
Old Windsor 
Berkshire, SL4 2SE
United Kingdom 
Telephone: 0870-225-0109 
For Australian inquiries:
24 hours a day 7 days a week
E.D. Oates Pty Ltd
76 - 82 Newlands Road
Reservoir VIC 3073
Australia
Telephone: 1-800-811-183 
For all other inquiries:
Monday - Friday    8 am — 4 pm 
BISSELL Homecare, Inc.
PO Box 1888
Grand Rapids, MI 49501 USA
Telephone: 01-616-453-4451 
Fax: 01-616-453-1383
BISSELL HOMECARE INC. IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY 
NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT. BISSELL’S LIABILITY 
WILL NOT EXCEED THE PURCHASE PRICE OF THE PRODUCT. 
*EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY
THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES 
EITHER ORAL OR WRITTEN. ANY IMPLIED WARRANTIES WHICH MAY ARISE 
BY OPERATION OF LAW, INCLUDING THE IMPLIED WARRANTIES OF 
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE 
LIMITED TO THE TWO YEAR DURATION FROM THE DATE OF PURCHASE AS 
DESCRIBED ABOVE.
©2004 BISSELL Homecare, Inc
Grand Rapids, Michigan
All rights reserved. Printed in Korea
Part Number 603-2101
Rev 10/04 
Visit our website at:
www.bissell.com