BenQ Xl2420te User Manual

							  21   How to assemble your monitor hardware
Adjusting the monitor height
To adjust the monitor height, hold both the left and the 
right sides of the monitor to lower the monitor or lift 
it up to the desired height.
• Avoid placing hands on the upper or lower part of the 
height-adjustable stand or at the bottom of the monitor, as 
ascending or descending monitor might cause personal injuries. 
Keep children out of reach of the monitor while performing this 
operation.
• If the monitor has been rotated to portrait mode and height adjustment is desired, you 
should be noted that the wide screen will keep the monitor from being lowered to its 
minimum height.
 
						

							22  How to assemble your monitor hardware  
Rotating the monitor
1. Pivot the display.
Before rotating the monitor with a portrait viewing orientation, the display has to be rotated 90 
degrees.
Right-click the desktop and select 
Screen resolution from the popup menu. Select Portrait in 
Orientation, and apply the setting.
Depending on the operating system on your PC, different procedures should be followed to adjust the screen 
orientation. Refer to the help document of your operating system for details.
2. Fully extend the monitor and tilt it.
Gently lift the display up and extend it to the maximum 
extended position. Then tilt the monitor.
The monitor should be vertically extended to allow to rotate 
from landscape to portrait mode.
3. Rotate the monitor 90 degrees clockwise as 
illustrated.
To avoid the edge of the LCD display hitting the monitor base 
surface while it is being rotated, do tilt and extend the monitor 
to the highest position before you start to rotate the display. You 
should also make sure there are no obstacles around the monitor 
and there is enough room for cables.
90
 
						

							  23   How to assemble your monitor hardware
Viewing angle adjustment
You may position the screen to the desired angle with -5° to + 20° monitor tilt, 70° (left and 
right total) monitor swivel, and 130 mm monitor height.
(For XL2720) You may position the screen to the desired angle with -5° to + 20° monitor tilt, 
90° (left and right total) monitor swivel, and 140 mm monitor height.
4. Adjust the monitor to the desired viewing 
angle.
-5-5O O ~ +20~ +20O-5O ~ +20O-35-35O O ~ +35~ +35O-35O ~ +35O
130 mm
-5-5O O ~ +20~ +20O-5O ~ +20O
-45-45O O ~ +45~ +45O-45O ~ +45O
140 mm
XL2720
 
						

							24  How to assemble your monitor hardware  
Using the monitor wall mounting kit
The back of your LCD monitor has a VESA standard mount with 100mm pattern, allowing the 
installation of a wall mount bracket. Before starting to install a monitor wall mounting kit, 
please read the precautions carefully.
Precautions
• Install your monitor and monitor mounting kit on a wall with flat surface.
• Ensure that the wall material is stable to support the weight of the monitor.
• Turn off the monitor and the power before disconnecting the cables from the LCD monitor.
The maximum dimensions of the VESA mounting bracket compatible with your monitor are 125mm x 125mm.
1. Remove the monitor stand.
Detach the monitor stand as instructed in step 1~2 
in How to detach the stand and the base on page 
18.
2. Remove the screws on the back cover.
Use a cross-pointed screwdriver to release the 
screws on the back cover. The use of a 
magnetic-head screwdriver is recommended to 
avoid of losing the screws.
In case you intend to use your monitor on the stand in the 
future, please keep the monitor base, monitor stand, and 
screws somewhere safe for future use.
3. Follow the instruction manuals of the wall 
mount bracket you purchased to complete 
the installation.
 
						

							  25   Getting the most from your BenQ monitor
Getting the most from your BenQ monitor
To gain the most benefit from your new BenQ color LCD flat screen monitor, you should 
install the custom BenQ LCD Monitor driver software as provided on the BenQ LCD Monitor 
CD-ROM.
The circumstances under which you connect and install your BenQ LCD Monitor will 
determine which process you need to follow to successfully install the BenQ LCD Monitor 
driver software. These circumstances relate to which version of Microsoft Windows you are 
using, and whether you are connecting the monitor and installing the software onto a new 
computer (without existing monitor driver software), or whether you are upgrading an existing 
installation (which already has existing monitor driver software) with a newer monitor.
In either case however, the very next time you turn on your computer (after connecting the 
monitor to your computer), Windows will automatically recognize the new (or different) 
hardware, and will launch its 
Found New Hardware wizard.
Follow the wizard instructions until it asks you to select a monitor model. At that point, click 
the 
Have Disk button, insert the BenQ LCD Monitor CD-ROM and select the appropriate 
monitor model. Further details and step-by-step instructions for either an automatic (new) or 
upgrade (existing) installation, see:
• How to install the monitor on a new computer on page 26.
• How to upgrade the monitor on an existing computer on page 27.
• If you require a User Name and Password to login to your Windows computer, you must be logged on as an 
Administrator or as a member of the Administrators group in order to install the monitor driver software. 
Furthermore, if your computer is connected to a network which has security access requirements, network 
policy settings may prevent you from installing software on your computer.
• To check the name of the purchased model, refer to the specification label on the back of the monitor.
 
						

							26  Getting the most from your BenQ monitor  
How to install the monitor on a new computer
This instruction details the procedure for selecting and installing the BenQ LCD Monitor driver 
software on a new computer which has never had a monitor driver installed before. This 
instruction is only suitable for a computer which has never been used before, and for which the 
BenQ LCD Monitor is the first ever monitor to be connected to it.
1.  Follow the instructions in How to assemble your monitor hardware on page 11. 
When Windows starts, it will automatically detect the new monitor and launch the 
Found 
New Hardware Wizard
. Follow the prompts until it displays the option to Install Hardware 
Device Drivers
.
2.  Insert the BenQ LCD Monitor CD-ROM into a CD drive on the computer.
3.  Check 
Search for a suitable driver for my device option, and click Next.
4.  Check the option for CD-ROM drives (uncheck all others) and click 
Next.
5.  Look to confirm that the wizard has selected the correct name of your monitor and click 
Next.
6.  Click 
Finish.
7.  Restart the computer.
If you are adding the BenQ LCD Monitor to an existing computer that has already had another monitor 
connected to it (and has monitor driver software installed), you should not be following these instructions. You 
should instead be following the instructions for How to upgrade the monitor on an existing computer.
To find the suitable driver files for the purchased model, refer to the following table.
Driver filesSuitable models
XL2420t XL2420T
XL2420te XL2420TE
XL2420Z XL2420Z / XL2420ZE
XL2420TX XL2420TX
XL2420G XL2420G / XL2420GE
XL2720T XL2720T
XL2720Z XL2720Z / XL2720ZE
 
						

							  27   Getting the most from your BenQ monitor
How to upgrade the monitor on an existing computer
This instruction details the procedure for manually updating the existing monitor driver 
software on your Microsoft Windows computer. It is currently tested as compatible for 
Windows 8.1, Windows 8, and Windows 7 Operating System (OS). 
Installing monitor driver software involves selecting an appropriate information file (.inf) on the 
BenQ LCD Monitor CD-ROM for the particular model monitor you have connected, and 
letting Windows install the corresponding driver files from the CD. You need only steer it in 
the right direction. Windows has an Upgrade Device Driver Wizard to automate the task and 
guide you through the file selection and installation process. 
See:
• How to install on Windows 8 (8.1) system (selected models only) on page 28.
• How to install on Windows 7 system on page 29.
The BenQ LCD Monitor driver for your model may well function perfectly with other versions of Windows, 
however, as at the time of writing, BenQ has done no testing of this driver on other versions of Windows and 
cannot guarantee its operation on those systems.
 
						

							28  Getting the most from your BenQ monitor  
How to install on Windows 8 (8.1) system (selected models 
only)
1.  Open Display Properties.
Move the cursor to the lower-right of the screen or press the 
Windows + C buttons on the 
keyboard to bring up the 
Charm bar. Go to Settings, Control Panel, Devices and 
Printers
 and right-click the name of your monitor from the menu.
Alternatively, right-click the desktop and select Personalize, Display, Devices and Printers, 
and right-click the name of your monitor from the menu.
2.  Select Properties from the menu.
3.  Click the 
Hardware tab.
4.  Click 
Generic PnP Monitor, and then the Properties button.
5.  Click the 
Driver tab and the Update Driver button.
6.  Insert the BenQ LCD Monitor CD-ROM into a CD drive on the computer.
7.  In the 
Update Driver Software window, select the option Browse my computer for 
driver software
.
8.  Click 
Browse and navigate to the following directory: d:\BenQ_LCD\Driver (where d is 
the drive letter designator for the CD-ROM drive).
9.  Select the correct folder name of your monitor from provided driver list, and click 
Next.
This will copy and install the appropriate monitor driver files to your computer.
10. Click 
Close.
You may be prompted to restart your computer after the driver update is complete.
The drive letter for your CD drive may differ from the example above depending upon your system - it may be 
D: or E: or F: etc.
 
						

							  29   Getting the most from your BenQ monitor
How to install on Windows 7 system
1.  Open Display Properties.
Go to 
Start, Control Panel, Hardware and Sound, Devices and Printers and right-click 
the name of your monitor from the menu.
Alternatively, right-click the desktop and select 
Personalize, Display, Devices and 
Printers
, and right-click the name of your monitor from the menu.
2.  Select 
Properties from the menu.
3.  Click the 
Hardware tab.
4.  Click 
Generic PnP Monitor, and then the Properties button.
5.  Click the 
Driver tab and the Update Driver button.
6.  Insert the BenQ LCD Monitor CD-ROM into a CD drive on the computer.
7.  In the 
Update Driver Software window, select the option Browse my computer for 
driver software
.
8.  Click 
Browse and navigate to the following directory: d:\BenQ_LCD\Driver (where d is 
the drive letter designator for the CD-ROM drive).
9.  Select the correct folder name of your monitor from provided driver list, and click 
Next.
This will copy and install the appropriate monitor driver files to your computer.
10. Click 
Close.
You may be prompted to restart your computer after the driver update is complete.
The drive letter for your CD drive may differ from the example above depending upon your system - it may be 
D: or E: or F: etc.
 
						

							30  Getting the most from your BenQ monitor  
How to watch 3D content on your monitor
Your monitor supports playing three-dimensional (3D) content transferred through DVI-D Dual 
Link or DP cable, depending on the purchased model. Yet you need to have the appropriate 
hardware equipment and software programs that are compatible with 3D playback.
System requirements
• BenQ LCD Monitor (XL20 series)
• Compatible 3D glasses
• PC with Microsoft Windows 7 or Windows 8 (8.1) Operating System
• Compatible graphics processing units (GPU) with the latest driver files installed
• Compatible software programs that play 3D playback
For the compatible accessories, visit 
http://www.nvidia.com/object/3d-vision-requirements.html. For the appropriate 3D players, 
check with the 3D content providers.
Playing 3D content
Follow the instruction manuals of your 3D accessories to install the hardware and the software. 
If the 3D glasses are properly connected and IR signal is detected, the IR emitter indicator on 
the bottom right of the monitor and on the IR emitter module (purchased separately for 
XL2420T / XL2420TE / XL2720) will light up.
To improve the performance of 3D glasses, you can do the following:
• On XL2420TX, check if there are any obstacles in front of the IR sensor located at the front 
top of the monitor that keep the sensor from receiving signals from the 3D glasses.
Go to 
System and Emitter Mode and change the setting as needed. See Emitter Mode 
(XL2420TX only) on page 57 for more information.
• Follow the instruction manuals of the 3D accessories to make adjustment.
If you want to adjust the brightness when watching 3D content, go to 
Picture and NVIDIA® 3D 
LightBoost
™. See Brightness (during 2D playback) / NVIDIA® 3D LightBoost™ (during 3D 
playback) on page 46 for more information.
3D content can be transferred to XL2420TX through HDMI cable (version 1.3 or above) as well.
• Not all menu options are available for 3D playback.
• For models with G-SYNC module, 3D playback is available in 
G-SYNC mode only.
• Contact NVIDIA or visit NVIDIA website (http://www.nvidia.com/page/home.html) for the purchase and the 
settings of the compatible GPU.
• Visit the NVIDIA website (www.nvidia.com/3DUpdate) for the latest GPU driver files.