BenQ W7000 Users Manual

  21
  Connecting with video equipment
Selecting an input source
The projector can be connected to multiple equipment at the same time. 
When the projector is first turned on, it will attempt to reconnect with 
the input source which was in use when the projector was last shut 
down.
To select the video source:
•  Using the remote control or projector
Press one of the Source keys on the remote control, or press SOURCE 
on the projector repeatedly until your desired signal is selected.
•  Using the OSD...

22 Connecting with video equipment  
Using the menus
The projector is equipped with multilingual On-Screen Display (OSD) menus for making various 
adjustments and settings.
Below is the overview of the OSD menu.
To use the OSD menus, please set the OSD menu to your familiar language.
Securing the projector
Using a security cable lock
The projector has to be installed in a safe place to prevent theft. Otherwise, purchase a lock, such as the 
Kensington lock, to secure the projector. You can locate a...

  23
  Connecting with video equipment
Utilizing the password function
For security purposes and to help prevent unauthorized use, the projector includes an option for setting 
up password security. The password can be set through the On-Screen Display (OSD) menu. Once the 
password is set and this function is selected, the projector is password-protected. Users who do not 
know the correct password can not use the projector.
You will be inconvenienced if you activate the password functionality and...

24 Connecting with video equipment  
Entering the password recall procedure
1. Make sure the Input Password page displays on screen. Press and 
hold EXIT on the projector or remote control for 3 seconds. The 
projector will display a coded number on the screen.
2. Write down the number and turn off your projector.
3. Seek help from the local BenQ service center to decode the number. 
You may be required to provide proof of purchase documentation to 
verify that you are an authorized user of the...

  25
  Connecting with video equipment
Adjusting the projected image
Adjusting the projection angle 
There are four adjuster feet on the bottom of the projector. These can be 
used if necessary to change the projection angle. Screw the feet in or out 
as appropriate to aim and level the projection angle.
If the screen and the projector are not perpendicular to each other, the 
projected image becomes vertical trapezoidal. To correct this problem, see Correcting picture distortion 
on page 25 for...

26 Connecting with video equipment  
Using the preset and user modes
Selecting a preset mode
The projector is preset with several pre-defined picture modes so that you can choose one to suit your 
operating environment and input source picture type.
To select a picture mode that suits your need:
•  Using the remote control
1. Press PRESET MODE repeatedly or USER 1, USER 2/ISF 
NIGHT, USER 3/ISF DAY, DEFAULT on the remote control, or 
PRESET MODE on the projector repeatedly until your desired 
mode is...

  27
  Connecting with video equipment
Setting the User 1/User 2/User 3 mode
There are three user-definable modes if the current available picture modes are not suitable for your 
need. You can use one of the picture modes (except the selected User mode) as a starting point and 
customize the settings.
1. In the Picture -- Basic menu, highlight Preset Mode and press  /
 to select User 1, User 2, or User 3 mode.
2. Press  to highlight Load Settings From.
This function is only available when User 1, User...

28 Connecting with video equipment  
Fine-tuning the picture quality
No matter what picture mode you have selected, you are able to fine-tune those settings to fit every 
presentation purpose. Those adjustments will be saved to the preset mode you are at when you exit the 
OSD menu.
Adjusting Brightness
Highlight Brightness in the Picture -- Basic menu and 
adjust the values by pressing  /  on the projector or 
remote control.
The higher the value, the brighter the picture. And the 
lower the setting,...

  29
  Connecting with video equipment
The higher the value, the more reddish the flesh tones in the picture become. The lower the value, the 
more greenish the flesh tones in the picture become.
The Brightness, Color, Contrast, Tint functions can also be accessible 
by pressing BRIGHTNESS, COLOR, CONTRAST, TINT on the 
remote control to display the adjustment bar and then you can press  /
 to adjust the values.
Advanced picture quality controls
There are more advanced functions in the Picture --...

30 Connecting with video equipment   *About color temperatures:
There are many different shades that are considered to be white for various purposes. One of the common 
methods of representing white color is known as the “color temperature”. A white color with a low color 
temperature appears to be reddish white. A white color with a high color temperature appears to have more 
blue in it.
Setting a preferred color temperature
To set a preferred color temperature:
1. Highlight Color Temperature and...