BenQ W20000/w5000 Digital Projector Home Cinema Series User Manual

  31
  Using the projector
English5.Real: This setting displays the image in a one-to-one pixel mapping 
without alteration or resize in the centre of the projection. This is most 
suitable for use with PC and RGBHD source inputs.
The black portions are inactive areas and the white portions are active areas.
OSD menus can be displayed on those unused black areas.
Using Panamorph lenses (optional)
Panamorph lenses allow you to convert 16:9 projectors to the full 2.35:1 aspect ratio of most of major motion...

32 Using the projector  
EnglishDisplaying more than one image source simultaneously
Your projector is capable of displaying pictures simultaneously from two input sources, which can be used to 
enhance your presentation in an interesting way. Ensure the signals you want to display are correctly connected 
to the projector.
To display the PIP window:
• Using the remote control
Press PIP to display the PIP page and make adjustments by following the steps 
starting from step 3 in the section Using the OSD...

  33
  Using the projector
EnglishCreating your own startup screen
In addition to selecting the projector preset startup screen from among BenQ logo or Blue screen, you can make 
your own startup screen that is a picture projected from your computer or video source. 
To create your own startup screen, project the picture you want to use as your startup screen from either a 
computer or video source. The rest steps are as follows.
•Using the OSD menu
1. Press MENU and then press  /  until the System Setup...

34 Using the projector  
EnglishTu r n i n g  t h e  p o w e r  o f f
To turn the projector off, press POWER ( ) on the projector or remote 
control and a warning message appears. Press POWER again.
• The Power indicator light flashes orange and the fans run for about 
two minutes to cool the lamp. The projector will not respond to any 
commands until the cooling process is complete.
• Then, the Power indicator light is a steady orange once the cooling 
process has finished and fans stop.
• If the...

  35
  Using the projector
EnglishOn-Screen Display (OSD) menus
On-Screen Display (OSD) structure
Please note that the on-screen display (OSD) menus vary according to the signal type selected.
Main menu Sub-menu Options
Picture -- Basic
Picture ModeCinema/Dynamic/Standard/User 1/User 2/User 
3
Load Settings From
Brightness 0–100
Contrast 0–100
Color 0–100
Tint -20–+20
Sharpness 0–8
Reset Picture Settings
Rename User Mode
Picture -- 
Advanced
Black Level 0 IRE/7.5 IRE
Clarity ControlNoise Reduction...

36 Using the projector  
English
Note that the menu items are available when the projector detects at least one valid signal. If there is no 
equipment connected to the projector or no signal detected, limited menu items are accessible.
The default values listed in this manual, especially on pages 37-39, are for reference only. They may vary from the 
projectors due to the continuous improvement to the products.
System Setup
Language
Splash Screen BenQ/Blue/My Screen
My Screen
Projector PositionFloor...

  37
  Using the projector
EnglishPicture -- Basic menu
Picture -- Advanced menu
FUNCTION
(default setting/value)DESCRIPTION
Picture Mode
(Cinema)
Pre-defined picture modes are provided so you can optimize your projector 
picture set-up to suit your program type. See Selecting a preset mode on 
page 24 for details.
Load Settings From
Selects a picture mode that most suits your need for the picture quality and 
further fine-tune the picture based on the selections listed below. See Setting the 
User...

38 Using the projector  
English
Display menu
System Setup menu
IRISSee Adjusting contrast ratio via IRIS on page 29 for details.
Lens ShiftSee Shifting the projection lens vertically on page 12 for details.
FUNCTION
(default setting / value)DESCRIPTION
Aspect Ratio
(Anamorphic)
There are several options to set the pictures aspect ratio depending on your input 
source. See Selecting the aspect ratio on page 30 for details.
Keystone
(0)
Corrects any keystoning of the picture. See Correcting picture...

  39
  Using the projector
English
Advanced Setup menu
Menu Settings
Menu Display Time (15 sec)
Sets the length of time the OSD will remain active after your last key press. The 
range is from 5 to 30 seconds in 5-second increments.
Menu Position (Center)
Sets the On-Screen Display (OSD) menu position.
Input SourceSelects an input source to be projected. See Selecting an input source on page 19 
for details.
Auto Source Search
(Off)
Sets whether the projector searches automatically for input sources. If...

40 Using the projector  
English
Information menu
This menu shows you the current operating status of the projector.
Some picture adjustments are available only when certain input sources are in use. Unavailable adjustments are not 
shown on the screen.
ISF
The ISF calibration menu is password protected and only accessible by authorized 
ISF calibrators. The ISF (Imaging Science Foundation) has developed carefully 
crafted, industry-recognized standards for optimal video performance and has 
implemented...