BenQ Sp820 User Manual

							
 
– 15 – 
ON-SCREEN DISPLAY (OSD) MENU SETTINGS 
OSD Menu Controls 
The projector has an OSD that lets you make image adjustments and change various settings.  
Navigating the OSD 
You can use the remote control cursor buttons or the buttons on the top of the projector to navigate 
and make changes to the OSD. The following illustration shows the corresponding buttons on the re-
mote control and on the projector. 
 
A. To open the OSD, press the Menu button.  
B. There are six menus. Press the cursor W X  
button to move through the menus.  
C. Press the cursor ST button to move up and 
down in a menu.  
D. Press W X to change values for settings, and 
then press Enter or X to confirm the new set-
ting. 
E. Press Menu to close the OSD or leave a sub-
menu. 
Note: 
Depending on the video source not all items in the OSD are available. For example, the Horizon-
tal/Vertical Position items in the Setup menu can only be modified when connected to a PC. Items 
that are not available cannot be accessed and are grayed out.   
						

							
DDDLLLPPP   PPPrrrooojjjeeeccctttooorrr   –––   UUUssseeerrr’’’sss   MMMaaannnuuuaaalll   
Setting the OSD Language 
You may want to reference the OSD on your projector while reading this section. Set the OSD lan-
guage to your preference before continuing (the default language is English). 
1. Press the Menu button. The Main menu appears. 
 
2. Press the cursor W X button until Tool is highlighted.  
 
3. Press the cursor ST button until Language is highlighted.  
4. Press the cursor W X until your language is displayed. 
5. Press the cursor X or Menu button to confirm the language, and close the OSD. 
– 16 –  
						

							
DDDLLLPPP   PPPrrrooojjjeeeccctttooorrr   –––   UUUssseeerrr’’’sss   MMMaaannnuuuaaalll   
OSD Menu Overview
Use the following illustration to quickly find a setting or determine the range for a setting.  
 
– 17 –  
						

							
DDDLLLPPP   PPPrrrooojjjeeeccctttooorrr   –––   UUUssseeerrr’’’sss   MMMaaannnuuuaaalll   
Main Menu  
Press the Menu button to open the OSD menu. Press the cursor W X button to move to the Main 
menu. Press the cursor ST button to move up and down in the Main menu. Press W X to change 
values for settings, and then press Enter or X to confirm the new setting. 
 
ITEM DESCRIPTION DEFAULT
Application 
Mode Press the cursor W X button to select the required Application Mode. Based on 
Source 
Brightness Press the cursor W X button to adjust the brightness. (Range: 0 – 100) 50 
Contrast Press the cursor W X button to adjust the contrast. (Range: 0 – 100) 50 
White Peak 
White Peak increases the output in the brightest whites without changing the 
blacks and dark grays. It crushes the whites slightly, but it does not appear to 
clip them or seriously obscure white detail. If you prefer a stronger image, 
adjust toward the maximum setting. For a smoother, more natural image, ad-
just toward the minimum setting. 
Press the cursor W X button to adjust the white peak. 
Based on 
Source 
Sharpness Press the cursor W X button to adjust the display sharpness (Range: 1 – 5) 3 
Color  
Temperature 
Press the cursor W X button to adjust the video tint/hue.  
(Range: Cool/Normal/Warm) Normal 
Saturation Press the cursor W X button to adjust the video saturation. (Range: 0 – 100) 50 
Tint Press the cursor W X button to adjust the video tint/hue. (Range: 0 – 100) 50 
Color Space 
Transfer 
Press the cursor W X button to adjust the color space Transfer.  
(Range: Auto – RGB – YPbPr – YCbCr) Auto 
Reset Resets all Main settings to default values — 
– 18 –  
						

							
DDDLLLPPP   PPPrrrooojjjeeeccctttooorrr   –––   UUUssseeerrr’’’sss   MMMaaannnuuuaaalll   
Main Menu Functions Available for Connected Source 
Function RGB DVI-D Component  Video S-video 
Application 
Function O O O O O 
Brightness O O O O O 
Contrast O O O O O 
White Peak O O O O O 
Sharpness O O O O O 
Color Temp O O O O O 
Saturation   O O O 
Tint   O O O 
Color Space 
Transfer O O O O O 
Reset O O O O O 
O = available to video source 
 
– 19 –  
						

							
DDDLLLPPP   PPPrrrooojjjeeeccctttooorrr   –––   UUUssseeerrr’’’sss   MMMaaannnuuuaaalll   
Setup Menu  
Press the Menu button to open the OSD menu. Press the cursor W X button to move to the Setup 
menu. Press the cursor ST button to move up and down in the Setup menu. Press W X to change 
values for settings, and then press Enter or X to confirm the new setting. 
 
ITEM DESCRIPTION DEFAULT
Horizontal 
Position Press the cursor W X button to move the image left or right. (Range: 0 – 100) 50 
(Centered)
Vertical  
Position Press the cursor W X button to move the image up or down. (Range: 0 – 100) 50 
(Centered)
Keystone Press the cursor W X button to correct distortion of the projected image.  
(Range: -50 – +50) 0 
Aspect Ratio Press the cursor W X button to toggle between the 4:3 standard format and the 
16:9 High Definition TV (HDTV) format. 4:3 
Advanced 
Setup See Advanced Setup on page 21. — 
Reset Resets Keystone and Aspect Ratio to default values — 
Setup Menu Functions Available for Connected Source 
Function RGB DVI-DComponent VideoS-video 
H Position O     
V Position O     
Keystone correction O O O O O 
Aspect Ratio O O O O O 
Advanced Setup O O O O O 
Reset O O O O O 
O = available to video source 
– 20 –  
						

							
DDDLLLPPP   PPPrrrooojjjeeeccctttooorrr   –––   UUUssseeerrr’’’sss   MMMaaannnuuuaaalll   
Advanced Setup 
Press the Menu button to open the OSD menu. Press W X to move to the Setup menu. Press ST 
to move to the Advanced Setup menu and then press Enter or X. Press ST to move up and down 
in the Advanced Setup menu. Press W X to change values for settings, and then press Enter or X 
to confirm the new setting. 
 
ITEM DESCRIPTION DEFAULT
User Color 
This feature adjusts the color balance in each color of RGB (red, green, 
blue), and their neutral colors (cyan, magenta, yellow, white) by using color 
correction adjustment. Increasing a color’s setting heightens the intensity of 
that color on the screen, while a lower setting makes the color less intense.  
Press ST to select a color. 
Press W X to adjust the selected color. (Range: 0 – 100) 
80 
Logo  
Display 
Press W X to enable or disable if the logo displays when the projector starts, 
and when no source is detected. (Range: On – Off) On 
Fan Speed Press the cursor W X button to toggle between normal and high fan speed. 
Set Fan Speed to High in altitudes over 1500 meters (5000 feet). Normal 
– 21 –  
						

							
DDDLLLPPP   PPPrrrooojjjeeeccctttooorrr   –––   UUUssseeerrr’’’sss   MMMaaannnuuuaaalll   
ITEM DESCRIPTION DEFAULT
Security Lock 
Press the cursor W X button to enable or disable Security Lock. When you 
enable Security Lock a Register Password dialog box appears: 
 
 
You can only use the following four cursor buttons, STW X in the pass-
word fields. Press the cursor buttons five times in any order and confirm to 
set the password. When the password is enabled, it must be entered every 
time after you power on the projector. See Setting an Access Password (Se-
curity Lock) on page 12 for steps on setting the password. 
— 
Audio Input 
Press the cursor W X button to toggle between PC and Video input  
channels. 
Press the cursor W X button to select different audio input channel. 
Data 
source: PC
Video 
source: 
Video 
Reset Press Enter or X to reset advanced setup settings to default values — 
 
Note: 
If Security Lock is enabled, you must enter the password every time the projector is turned on. 
However, if the projector is already turned on, Security Lock can be disabled without knowing the 
current password. 
 
– 22 –  
						

							
DDDLLLPPP   PPPrrrooojjjeeeccctttooorrr   –––   UUUssseeerrr’’’sss   MMMaaannnuuuaaalll   
User Color 
Press the Menu button to open the OSD menu. Press W X to move to the Setup menu. Press ST 
to move to the Advanced Setup menu and then press Enter or X. Press ST to move to the User 
Color menu and then press Enter or X. Press ST to move up and down to select a color. Press  
W X to change values for settings, and then press Enter or X to confirm the new setting. 
 
ITEM DESCRIPTION DEFAULT
Red Press the cursor W X button to adjust the red color level.  
(Range: 0 - 100) 80 
Green Press the cursor W X button to adjust the green color level.  
(Range: 0 - 100) 80 
Blue Press the cursor W X button to adjust the blue color level.  
(Range: 0 - 100) 80 
Cyan Press the cursor W X button to adjust the cyan color level.  
(Range: 0 - 100) 80 
Magenta Press the cursor W X button to adjust the magenta color level.  
(Range: 0 - 100) 80 
Yellow Press the cursor W X button to adjust the yellow color level.  
(Range: 0 - 100) 80 
White Press the cursor W X button to adjust the white color level.  
(Range: 0 - 100) 80 
Reset Resets all User Color settings to default values — 
 
– 23 –  
						

							
DDDLLLPPP   PPPrrrooojjjeeeccctttooorrr   –––   UUUssseeerrr’’’sss   MMMaaannnuuuaaalll   
Config Menu  
Press the Menu button to open the Main menu. Press the cursor W X button to move to the Config 
menu. Press the cursor ST button to move up and down in the Config menu. Press W X to change 
values for settings, and then press Enter or X to confirm the new setting. 
 
ITEM DESCRIPTION DEFAULT
Blank Screen 
Press the cursor W X button to select a background color for the blank 
screen.  
(Range: Black – Red – Green – Blue – White)  
Blue 
Auto Source 
Press the cursor W X button to enable or disable automatic source detec-
tion.  
(Range: On – Off) 
On 
Auto Power 
Off 
Press the cursor W X button to enable or disable automatic lamp shutdown 
after 10 minutes of inactivity.  
(Range: On – Off) 
Off 
Direct Power 
On 
Press the cursor W X button to enable or disable direct power on. When 
enabled, the projector powers on automatically when AC power is applied. 
(Range: On – Off) 
Off 
Volume Press the cursor W X button to adjust the audio volume level.  
(Range: 0 – 8) 4 
Menu  
Position 
Press the cursor W X button to position the OSD on screen.  
(Range: Left – Right – Center – Down – Up) Center 
Menu Display Press the cursor W X button to determine the timeout delay of the OSD.  
(Range: 10 – 20 sec.) 15 secs 
Menu  
Transparency 
Press the cursor W X button to set menu screen translucency.  
(Range: 0% – 100%) 0% 
Reset Resets all Config items to default values — 
Note: 
The Config menu functions are available to all video sources. 
– 24 –