BenQ Projector MX810ST/MW811ST/MX812ST User Manual

							Operation 41
Wireless connection
To connect to the projector wirelessly, you have to plug a BenQ wireless dongle (optional) to 
the USB Type A connector on the projector, and then only a few OSD configuration steps are 
required.
1. Make sure the projector is turned on.
2. Do one of the following: 
•Press NETWORK SETTING on the remote control. The Network Settings page 
is displayed. 
•Press MENU/EXIT and then press  /  until the SYSTEM SETUP: Advanced 
menu is highlighted. Press   to highlight Network Settings and press MODE/
ENTER. The Network Settings page is displayed.
3. Highlight Wireless LAN and press MODE/ENTER.
4. Make sure the Status is Connect.
5. Make sure the SSID information is displayed.
6. Press   to highlight Connection Mode and press  /  to select AP or Infrastructure. 
In AP mode, you need to use your computer’s wireless connection utility to search the 
projector’s SSID and connect to it. Then you can search the projector with Q 
Presenter. To use Infrastructure mode, you should connect both your computer and 
projector to the same AP router and make connections with the IP address.
•  There are more wireless settings available on the Projector Network display System > 
Admin > Wireless LAN page. 
•  If you need more information about AP and Infrastructure modes, please refer to user 
documentations for Wireless Routers which are usually available on 3C stores. 
						

							Operation 42
Controlling the projector remotely through a web browser
Once you have the correct IP address for the projector and the projector is on or in standby 
mode, you can use any computer that is on the same local area network to control the 
projector.
•  If you are using Microsoft Internet Explorer, make sure it is version 7.0 or higher.
•  The screenshots in this manual are for reference only, and may differ from the actual 
design.
1. Enter the address of the projector in the address bar of your browser and press Enter.
2. The main page of the Projector Network Display System appears. This web page 
provides access to a variety of functions with a simple click.
3. Click Download to save Q Presenter software on your computer. See Displaying 
images through Q Presenter on page 50 for details. 
						

							Operation 43 4. The Virtual Keypad page displays a virtual keypad with which you can control the 
projector as if using the physical keypad on the projector. See Projector on page 10 
for how to operate it.
5. The Display Setting page provides some selective OSD menu items necessary for 
controlling the projector or adjusting the projected pictures. See the chapter Menu 
operation for how to use them. 
						

							Operation 446. The Picture Setting page provides all the OSD menu items in the PICTURE menu for 
adjusting the projected pictures. See 2. PICTURE menu on page 59 for how to use 
them.
7. The Information page displays the information about the projector status, network 
status. 
						

							Operation 45 8. The Conference Control page allows you to control the display location in the same IP 
address when there are multiple users connecting to the projector.
9. The Crestron (eControl) page displays the Crestron eControl user interface. The 
eControl page provides a variety of virtual keys to control the projector or adjust the 
projected pictures. 
i. These buttons function the same as the ones on the OSD menus or remote 
control. See 2. PICTURE menu on page 59 and Remote control on page 11 for 
details.
ii. To switch input source, click your desired signal.
iii. The software is available in multiple languages. 
The Menu button can also be used to go back to previous OSD menu, exit and 
save menu settings.
i
i
ii
i
iii 
						

							Operation 46The tools page allows you to manage the projector, configure the LAN control settings 
and secure access of remote network operation on this projector.
i. You can name the projector, keep track of its location and the person in charge of 
it.
ii. You can adjust the Network Settings.
iii. Once set, access to the remote network operation on this projector has been 
password-protected.
iv. Once set, access to the tools page has been password-protected.
After making the adjustments, press the Send button and the data will be saved 
in the projector.
v. Press exit to go back to the remote network operation page.
The info page displays the information and status of this projector.
For more information, visit http://www.crestron.com & www.crestron.com/
getroomview.
iv
iii
v
i
ii
Press Exit to 
go back to the 
remote network 
operation page. 
						

							Operation 47 6. To have access to the Admin page, you need to enter a password. The page provides 
more network settings. The default password is “0000”. If you want to change the 
password, enter the Basic page.
The Basic page allows you to change the password and set the maximum number of 
connected computers. The number of connected computer may affect the network 
display performance. 
						

							Operation 48The Wired LAN page allows you to adjust the Wired LAN settings.
The Wireless LAN page allows you to adjust the Wireless LAN settings.
The maximum length for SSID is 16 bytes. Please use different SSID when more 
than two projectors are connecting through wireless LAN. 
						

							Operation 49 The Mail page allows you to send alert e-mail to your ITS administrator.
You can first try the Mail Test function to check if the Alert Mail works.
7. These quick buttons are always provided on the web page for you to operate the 
projector. 
						

							Operation 50
Displaying images through Q Presenter
Downloading and installing Q Presenter
Q Presenter is an application running on the host PC. It helps connect your computer to an 
available network projector and transfer the desktop contents to the network projector via 
local network connection.
1. Enter the main page of the Projector Network Display System. See steps 1-2 on page 42 
for details.
2. Click the Download icon.
3. When the download is complete, install the software to your computer by clicking the 
exe file. Follow the on-screen instructions to complete the installation.
4. Launch Q Presenter.
Using Q Presenter
1. The Search page allows you to search and connect to a projector.
• To connect to a projector, type the projector IP address and click Connect. 
• To search for projectors, simply click Search to list all the projectors on the same 
local area network. Click the desired projectors in the Search result list, and click 
Connect. You can also type a desired projector name and click Search.
41
25
3
&