BenQ Projector MP780 ST+ User Manual

							Operation
71
How to hold the PointDraw™ pen 2.0
You can hold the PointDraw™ the way you would hold a normal pencil or pen, or you can 
hold it like a remote control - use in whichever position is most comfortable.
If the PointDraw™ pen is far away from the screen, be sure to press the left mouse button to 
click and drag.
Avoid shadows!
The PointDraw™ pen wont work if its tip is in a shadow or if it is pointing at a shadow:
or
Correct (no shadow) Incorrect (shadow)
28%12%
28%
28%
28%12%
28%
X
28% 
						

							Operation 72
PointDraw™ pen 2.0 features
Dual Pen operation
Now, MP780 ST+/MW860USTi is ready for PointDraw™ pen 2.0 and support up to two 
pens.
For Installing Q Draw software
1. Please ensure the BenQ projector is connected with the computer.
2. Please go to “System Setup: Basic” on projector OSD menu and change the 
PointDraw™ to “Dual Pen” for dual pen function activation.
MP780 ST+/MW860USTi can select three PointDraw™ modes via OSD menu setting.
You can go to: 
Right mouse button/
Color selection
Left mouse button
Tip
Battery status indicator
Solid Red: Battery charging
 Blinking: Low battery
Connection indicator
Solid Blue: Paired with BenQ 
projector
Blinking: Attempt to pair 
with the projector
USB connector
Wrist strap holder
Projector’s On/Off switch
Sensor 
						

							Operation
73 System Setup: Basic→PointDraw™ to select Dual Pen, Single Pen, or Off.
Single Pen
For optimized interactive speed, it is recommended to select “Single Pen” in PointDraw™ 
settings.
Dual Pen
Please go to “System Setup: Basic” on projector OSD menu and change the PointDraw™  to 
“Dual Pen” for dual pen function activation.
Select   icon on Q Draw 2.0 software for dual pen feature activation.
When switching between PointDraw™ modes, it will take about 30 seconds to re-flash modes, 
the delay time depends on computer response time.
Troubleshooting
• If the pen doesnt work at all, or it works intermittently, try one of these solutions:
- If the pens battery light is blinking or lit, then the pens battery is fully discharged; 
connect the pen to the USB power adapter or your computer.
- Make sure the pen is not pointing at a shadow and make sure its tip is not in a 
shadow.
- If the room is brightly lit, reduce the room illumination.
- If youre trying to use the computers mouse at the same time as the pen, point the 
pen away from the screen while using the mouse.
• If accurate clicking is difficult, hold the pen steadier when clicking.
• If the mouse pointer is in the wrong place on the screen, or the mouse pointers 
movement is restricted to only part of the screen, make sure your projector is 
displaying the computers screen and not some other source (such as DVD, VCR, etc.). 
To change the source, press the SOURCE button on the projector or remote control. 
						

							Operation 74• If the pen has the gap problem between the tip and the cursor on your Apple 
computers, install the scaling fix that came with the user manual CD-ROM: 
i. Mount the "ScalingFix.dmg" disk image - just double-clicking the file should 
auto-mount it.
ii. If you dont see the file on the "ScalingFix" volume, you may need to double-click 
the disk image icon on the desktop.
iii. Double-click "PointDraw Scaling Fix". The installer should run, follow the 
prompts.
iv. Right-click on the "ScalingFix" disk image icon on the desktop, and choose 
"Eject" to un-mount the volume.
v. If the USB device is already plugged-in, youll need to un-plug and re-plug it in.
It is suggested to install the “ScalingFix.dmg” file on MAC OS 10.5.0 or higher.
PointDraw™ pen 2.0 specifications
Operation frequency2.4 GHz ISM Band
Rechargeable battery
Model name
Normal voltage
Normal capacity1 pcs
CR17360A
3.6V
780 mAh
Storage temperature-10°C-60°C
Operation temperature0°C-40°C
Operation humidity20%-85% (ambient temperature
						

							Operation
75
Shutting down the projector
1. Press Power on the projector. A 
confirmation message displays prompting you. 
If you dont respond in a few seconds, the 
message will disappear. If you use the remote 
control, press OFF to shut down the 
projector.
2. Press Power on the projector a second 
time. The POWER indicator light flashes 
orange, the projection lamp shuts down, and 
the fans will continue to run to cool down the 
projector. 
To protect the lamp, the projector will not respond to 
any commands during the cooling process.
3. Once the cooling process finishes, the 
POWER indicator light is a steady orange 
and fans stop.
4. Disconnect the power cord from the power putlet if the projector will not be used 
in an extended period of time.
• If the projector is not properly shut down, to protect the lamp, when you attempt to re-start 
the projector, the fans will run for a few minutes to cool down. Press Power again to start 
the projector after the fans stop and the POWER indicator light turns orange.
• Actual lamp lives may vary due to different environmental conditions and usage.
II
II 
						

							Operation 76
Menu operation
Menu system
Please note that the on-screen display (OSD) menus vary according to the signal type 
selected.
Main menu Sub-menu Options
1. 
DISPLAY
Wall ColorOff/Light Yellow/Pink/Light Green/
Blue/Blackboard
Aspect Ratio Auto/Real/4:3/16:9/16:10
Auto Keystone On/Off
Keystone
Position
Phase
H. Size
Digital Zoom
3D Sync On/Off
3D Sync Invert Disable/Invert
2. 
PICTURE
Picture ModeDynamic/Presentation/sRGB/Cinema/User 1/User 2
Reference Mode Dynamic/Presentation/sRGB/Cinema
Brightness
Contrast
Color
Tint
Sharpness
Brilliant Color On/Off
Color 
TemperatureT1/T2/T3/T4
3D Color 
ManagementPrimary Color R/G/B/C/M/Y
Hue
Saturation
Gain
Save Settings
3. SOURCEQuick Auto Search On/Off
Color Space ConversionAuto/RGB/YUV 
						

							Operation
77
4. 
SYSTEM 
SETUP: 
Basic
Presentation 
TimerTimer period1~240 minutes
Timer displayAlways/Last 1 Min/Last 2 Min/Last 
3 Min/Never
Timer positionTop-Left/Bottom-Left/Top-Right/
Bottom-Right
Timer counting 
directionCount Down/Count Up
Sound ReminderOn/Off
On/Off
Language
Projector PositionFront Table/Rear Table/Rear 
Ceiling/Front Ceiling
Menu SettingsMenu display time5 sec/10 sec/15 sec/20 sec/25 sec/
30 sec
Menu positionCenter/Top-left/Top-right/Bottom-
right/Bottom-left
Reminder 
MessageOn/Off
Operation 
SettingsDirect Power On On/Off
Auto Power OffDisable/5 min/10 min/15 min/20 
min/25 min/30 min
Blank TimerDisable/5 min/10 min/15 min/20 
min/25 min/30 min
Sleep TimerDisable/30 min/1 hr/2 hr/3 hr/4 hr/
8 hr/12 hr
Remote 
ReceiverFront+Rear/Front/Rear
Panel Key LockOn/OffYe s / N o
Background 
ColorBenQ/Black/Blue/Purple
Splash Screen BenQ/MyScreen/Black/Blue
MyScreenCapture Yes/No
PointDraw™Single Pen/Dual 
Pen/Off
English/Français/Deutsch/Italiano/
Español/Русский/Äœ[/ŽD[0
_Î,0/Svenska/Nederlands/
Türkçe/Čeština/Português/ไทย/Polski/
Magyar/Hrvatski/Română/Norsk/
Dansk/Български/Suomi/Indonesia/
Ελληνικά 
						

							Operation 78
5. 
SYSTEM 
SETUP: 
Advanced
Quick Cooling On/Off
High Altitude ModeOn/Off
Audio SettingsMuteOn/Off
Volume
Microphone 
Volume
Power on/off Ring 
ToneOn/Off
Lamp SettingsLamp Mode Normal/Economic
Reset lamp timer
Equivalent lamp hour
Security 
SettingsChange password
Change Security 
SettingsPower on Lock
Splash Screen On Lock
We b  C o n t r o l  L o c k
Baud Rate2400/4800/9600/14400/19200/ 
38400/57600/115200
Test PatternOn/Off
Closed CaptionClosed Caption 
EnableOn/Off
Caption Version CC1/CC2/CC3/CC4
Standby 
SettingsNetworkOn/Off
MicrophoneOn/Off
Monitor OutOn/Off
Network 
SettingsWired LANStatus
DHCP
IP Address
Subnet Mask
Default Gateway
DNS
Apply
Wireless LANStatus
SSID
IP Address
Connection Mode
Remote DesktopAccount
Password
Connect
Projection Log in 
codeOn/Off
Reset All 
Settings 
						

							Operation
79 Note that the menu items are available when the projector detects at least one valid signal. 
If there is no equipment connected to the projector or no signal detected, limited menu 
items are accessible.
6. 
INFORMA
TION
FAQ-Image and Installation
FAQ-Features and Service
Current System StatusSource
Picture Mode
Resolution
Color System
Equivalent Lamp Hour
Firmware Version 
						

							Operation 80
Description of each menu
• The default values listed in this manual, especially on pages 80-89, are for reference only. 
They may vary between the projectors due to the continuous improvement to the  
products.
FUNCTIONDESCRIPTION
Wall ColorCorrects the projected picture’s color when the projection surface is 
not white. See Using Wall Color on page 41 for details.
Aspect RatioThere are four options to set the images aspect ratio depending on 
your input signal source. See Selecting the aspect ratio on page 39 
for details.
Auto 
Key s t o n eAuto corrects any keystoning of the image.
KeystoneCorrects any keystoning of the image. See Correcting keystone on 
page 33 for details.
Position
Displays the position adjusent page. To move the projected image, 
use the directional arrow keys. The values shown on the lower 
position of the page change with every key press you made until they 
reach their maximum or minimum.
This function is only available when a PC signal (analog RGB) is 
selected.
Phase
Adjusts the clock phase to reduce image 
distortion.
This function is only available when a PC 
signal (analog RGB) is selected.
H. Size
Adjusts the horizontal width of the image.
This function is only available when a PC signal (analog RGB) is 
selected.
Digital ZoomMagnifies or reduces the projected image. See Magnifying and 
searching for details on page 38 for details.
1. DISPLAY menu