BenQ Projector LU9715 User Manual

51
▲▼ arrow keys to select desired memory, and press Enter key again to retrieve and to load the 
saved lens settings. The projector can keep 10 groups of lens settings. The memory position with 
lens settings will be marked in a different color and you can select only one of those settings. 
Load Memory
Save Memory
Clear Memory ENTER
No Signal MENUExit
Picture
Setup  Lens Memory Display
SetupAdvanced SystemInformation
Save Memory: Edit memory name and save current memory settings including lens shift,...

52
Type setting is correct before performing this function.
•  If Ultra Short Throw Lens is installed, make sure the support kit is detached before performing Center Lens. 
•  Digital Zoom
Digital Zoom
Digital Pan
Digital Scan
Reset Digital Zoom
Computer 1 MENUExit
Picture
Setup  Digital Zoom Display
SetupAdvanced SystemInformation
Digital Zoom: Press 
◄► arrow key to zoom in the projection image.
Digital Pan: Press  ◄► arrow key to pan out on projection image. This is valid only when the 
projected...

53
to exhaust the internal heat out of the projector ensuring its normal operation. However, the 
projector may turn off automatically if it is used in an environment with at excessively high 
temperature or in an area at a high altitude. In this case, you can enable this function by setting it 
to ON and have the cooling fan speed up to control the internal temperature of the projector.
Note:
An area is considered high altitude when it is above 5000 feet.
• Test Pattern
The projector features a set of...

54
Adjust Lines: Select adjust lines to on, enabling user to adjust overlapping area. 
Determine overlapped area (Range)
Determine overlapped position (Position)
Green MarkerGreen Marker
White Level: White level is to adjust the overlapping area for the blending. By selecting 
the areas of Top, Bottom, Left, and Right, the overlapping area can be optimized as the non-
overlapping area to display a seamless picture. Adjust the line to the Edge pixel line of the other 
projector.
Black Level: Black level...

55
OSD menu - System
Standby ModeEco
Off
Off
Off Off On
Logo
Auto Power Off
Direct Power On
Network
Background
Startup Logo
Trigger
Dynamic Black
Reset SystemNo Signal MENUExit
Picture
System Display
SetupAdvanced SystemInformation
• Standby Mode
Press 
◄► arrow key to toggle switch between Network and Eco mode.
Network:  The projector maintains in the standby status at the power consumption under 6W, 
the projector can be turned on using the power button or network control only, RS-232 control 
command...

56
Network ModeProjector Control
IP Address
Subnet Mask
Gateway
DHCP
Apply Off
Reset Network Computer 1 MENUExit
Picture
System  Network Display
SetupAdvanced SystemInformation
Press 
▲▼ arrow keys and Enter key to select network and its settings:
IP Address: To specify an IP address, press the Enter button to show the IP address input 
window. Use the  ◄► buttons to select the number in the address to be changed. Use the 
▲▼ 
buttons to increase or decrease the number in the IP address.
Subnet Mask :...

57
Press ◄► arrow key to enable/disable dynamic black mode.
•  Reset System
Press “Yes” to reset all settings to default in System OSD.
OSD menu - Information
Model BenQ Projector
9876543219876
1.00 MP01-SD09-FD19-LD08-22-RP01-3092
Serial Number
Software Version
Active Source BenQ Firmware Version
Displayport
74.1B4 MHz
1080i/60Hz
H: 33.750 KHz   V: 60.00 Hz
00047 HRS
Pixel Clock
Signal Format
H/V Refresh Rate
Light Source Usage
Thermal Status
Reset to Default Setting
Displayport MENUExit
Picture...

58
Additional information
Cleaning the lens
Clean the lens whenever you notice dirt or dust on the surface. Before you attempt to clean 
the lens, turn the projector off, unplug the power cable, and leave it several minutes to cool 
completely. Use a canister of compressed air to remove dust. (available from building hardware or 
photographic suppliers.)
If there is stubborn dirt or smudge marks, use a proper photographic lens brush or moisten a clean 
soft lens cloth with lens cleaner to gently wipe the...

59
Specifications
ModelLU9715
Display DeviceSingle Chip 0.67” DLP Technology
Resolution WUXGA
Input 
Terminals HDMI 
(Compatible with HDCP) 1
DVI-D 
(Compatible with HDCP) 1
Display Port 
(Compatible with HDCP) 1
3G-SDI In
(Compatible with HDCP) 1
Computer-1 (D-sub 15p) 1
Computer-2  (5BNC) 1
HDBaseT
(Shared with RJ-45)  1
Output 
Terminals Monitor Out
(D-sub 15 p) 1
Trigger
( φ 3.5mm stereo min jack) X1(DC 12V Output)
3D IR Sync
(VESA mini din) 1
3G-SDI Out 1
Control and  Service Lan (RJ-45)
1
Wired...

60
Dimension
500
583
PRESS
R elease
Lens211
Unit: mm
English