BenQ Projector LU9715 User Manual

41
Main menuSub-menu
Setup Language English
French
Español
Deutsch
Português
簡体中文
繁體中文
日本語
한국어
Svenska
Русский
Italiano
Projector Installation Front Table
Rear Table
Front Ceiling
Rear Ceiling
Auto Source Search On
Off
Lens Control (Zoom & Focus)
(Shift)
Lens Memory Load Memory Memory 1
Memory 2
Memory 3
Memory 4
Memory 5
Memory 6
Memory 7
Memory 8
Memory 9
Memory 10
Save Memory Memory 1
Memory 2
Memory 3
Memory 4
Memory 5
Memory 6
Memory 7
Memory 8
Memory 9
Memory 10
Clear Memory Memory 1
Memory 2...

42
Main menuSub-menu
Setup Clear MemoryMemory 9
Memory 10
Center Lens Execute
Digital Zoom Digital Zoom 0% ~ 100%
Digital Pan 0 ~ 100
Digital Scan 0 ~ 100
Reset Digital Zoom (OK) to execute
Light Settings Light Mode Eco 
Normal
Custom
Light Power 20%~100%
High Altitude On
Auto
Test Pattern Off
White
Black
Red
Green 
Blue
Checkerboard
CrossHatch
V. Burst
H. Burst
ColorBar
Test Pattern Plunge
Reset Setup Execute Reset Setup
Ye s
No
Main menu Sub-menu
Advanced BlankingTo p 0 ~ 360
Bottom 0 ~ 360
Left 0 ~...

43
Main menuSub-menu
Advanced Blue0 ~ 255
Reset Edge Blending ExecuteReset Edge Blending
Ye s
No
Main menu Sub-menu
System Standby Mode Network 
Eco 
Auto Power Off On
Off
Direct Power on On
Off
Network IP Address 192.168.00.100
Subnet mask 255.255.255.0
Gateway 192.168.00.254
DHCP On
Off
Apply ExecuteApply
OK
Cancel
Reset Network ExecuteReset Network
Ye s
No
Background Logo
Blue
Black
White
Startup Logo On
Off
Trigger On
Off
Dynamic Black On
Off
Reset System Execute Reset System
Ye s
No
English  

44
Main menuSub-menu
Information Model BenQ Projector
Serial Number W332AFHCY001
Software Version MP05-0D06-….
BenQ  Firmware Version 1.00
Active Source VGA
Pixel Clock 13.50 MHZ
Signal Format NTSC
H/V Refresh Rate H: 15.736 KHZ V: 60 HZ
Light Source Usage Inlet Ti1/Ti2 Temp.
DMD Temp.
Laser  B2/B3 Temp.
Outside Temp.
FAN Speed
Reset to Default Setting ExecuteReset All
Ye s
No
English  

45
OSD menu - Picture
Picture Mode
Brightness
Contrast
Saturation
Hue
Gamma
Color
Sharpness
Noise Reduction
Overscan
Reset PictureBright
No Signal MENUExit
Picture
Picture Display
SetupAdvanced SystemInformation
• Picture Mode
Press 
◄► arrow key to select display mode.
Bright: Output in the highest brightness for application that requires higher brightness.
Presentation : Display the best image effect for presentation or static image projection.
Cinema : Display in best color effect for film playback.
•...

46
Gain: Press ENTER to enter the Gain menu. Press 
◄► to adjust settings of red, green, blue, 
cyan, magenta, and yellow.
White Balance:  Press ENTER to enter the White Balance menu. Press 
◄► to adjust settings 
of red, green, and blue.
•  Sharpness
Press ENTER, and use 
◄► to adjust the sharpness, which changes the high-frequency details.
•  Noise Reduction
Press 
◄► arrow key to adjust noise of projection image. This function helps eliminating image 
noise caused by interlaced scanning input. In...

47
HDBaseT
This is the terminal to input uncompressed high-definition video (HD) via RJ-45 cable.
•  Aspect Ratio
Use this option to adjust aspect ratio.
For normal input of 16:10 the aspect ratio will look like the following images:
Normal output  
16:10 Aspect ratio of 
output screen 
5:4
Aspect ratio of 
output screen
2.35:1 Aspect ratio of 
output screen 
Letter Box
Aspect ratio of 
output screen
AutoAspect ratio of 
output screen
Real
Aspect ratio of 
output screen 
4:3
Aspect ratio of 
output...

48
Main / PIP Matrix
       Main Source
PIP sourceCOMPUTER1
COMPUTER2 HDMIDisplayPort HDBaseT 3G-SDIDVI-D
COMPUTER1 --∆ O -O
COMPUTER2 - -∆ O -O
HDMI -- ∆O -O
DisplayPort ∆∆∆ -∆ -
HDBaseT OOO - --
3G-SDI ---∆ O O
DVI-D OOO --O
O: Allowed  combination
- : Forbidden combination
∆ : Allowed combination (Pixel rate < 165MHz)
Position
Top Left: Selected sub source displays at Top Left position.
Top Right: Selected sub source displays at Top Right position.
Bottom Left: Selected sub source displays at Bottom...

49
HDMI 1.4a 3D input signal
HDMI 1.4a 3D signal sent to the projector through digital transmitter.
Side  by  Side  (Half):  Set  3D  format  to  Side  by  Side  manually. This  option  applies  to  HDMI  input 
signal or HDMI signal through a digital transmitter.
Top and Bottom: Set 3D format to Top and Bottom. This option applies to HDMI, DVI, or 
DisplayPort input signals or these signals through digital transmitter.
Frame Sequential: Set input format to Frame Sequential.
DLP Link: Select to disable...

50
OSD menu - Setup
Language
Projector Installation
Auto Source Search
Lens Control
Lens Memory
Center Lens
Digital Zoom
Light Settings
Test Pattern
Reset SetupFront Table
Off
No Signal MENUExit
Picture
Setup Display
SetupAdvanced SystemInformation
• Language
Select desired language displayed in your OSD menu: English, Français, Español, Deutsch, 
Português, 
簡体中文, 
繁體中文 , 
日本語 , 
한국어 , Svenska, 
Русский, Italiano.
•  Projector Installation
Press 
◄► arrow key to select Projector Installation : Front...