BenQ Pb6200/pb6100 Digital Projector Users Manual

Introduction 7
External Control Panel
3. Left
4. Exit
5. Right
6. Menu
2. Source7. Auto
8. Blank
11. Lamp indicator
10. Temp indicator
9. Power indicator
1. Power
Power
Press the Power key to turn the projector on 
or off.
Source
Selects signal sources from among PC, 
YP
bPr,  S-Video and Video.
 Left   Exit   Right   Menu
Menu will display the menu system on 
screen. Press Menu again to access the sub-
menus. Left and Right help you navigate 
among choices and settings in the menus 
and sub-menus....

Introduction 8
Adjuster
The projector is equipped with 1 quick-release adjuster foot. Push the button to adjust its tilt 
angle.
1. Lift the projector up and press the adjuster button to release the front adjuster.  
2. The adjuster will drop into position and be locked
3. If  the projected image is higher than the screen, you can screw the 2 rear adjusters to 
decrease the offset.  
123
3 

Introduction 9
Remote Control Description 
Your Remote Control at a Glance
Remote Control Effective Range
The remote sensors are located on the front and the back of the projector. It can function in 
a range of 30 degrees horizontally and 30 degrees vertically relative to a line that is a right 
angle to the remote sensors. The distance between the remote control and the remote 
sensors must be shorter than 6 meters (19.5 feet).  
Remote Control Functions
1. POWER, SOURCE, AUTO, BLANK, 3,4, EXIT, MENU...

Introduction 10
4. PRESET
Users can switch 4 kinds of preset modes. The preset mode changes each time when you 
press PRESET button 
•PC Signal: 
Presentation Mode (Default) --> Vivid Mode --> Video Mode --> Economic Mode
• YPbPr/ S-Video/ Video Signal: 
Gaming Mode (Default) --> Video Mode --> Cinema Mode --> Economic Mode
5. PIP SOURCE
User can activate PIP and select the source between S-Video and Video while the input 
source is PC. The PIP source changes in the order of S-Video, Video, and off.
6....

Installation 11
Installation
Screen Size
Place the projector at the required distance from the screen according to the desired picture 
size (see the table below). 
PB6200 (XGA) screen size chart (4:3 aspect ratio)
Distance 
from screenDiagonal measurement
Distance from 
screenDiagonal measurement
Minimum 
zoomMaximum 
zoomMinimum 
zoomMaximum 
zoom
feet inches feet inches feet inches meters cm meters cm meters cm
4 48 2.49 29.9 3.05 36.6 1 100 0.62 62.2 0.76 76.2
6 72 3.73 44.8 4.57 54.9 1.5 150 0.93...

Installation 12  
PB6200 (XGA) screen size chart (16:9 aspect ratio)
Distance 
from screenDiagonal measurement
Distance from 
screenDiagonal measurement
Minimum 
zoomMaximum 
zoomMinimum 
zoomMaximum 
zoom
feet inches feet inches feet inches meters cm meters cm meters cm
4 48 2.29 27.5 2.80 33.6 1 100 0.57 57.4 0.70 70.0
6 72 3.44 41.3 4.20 50.4 1.5 150 0.86 86.0 1.05 105.0
8 96 4.59 55.1 5.60 67.2 2 200 1.15 114.7 1.40 140.0
10 120 5.74 68.8 7.00 84.0 2.5 250 1.43 143.4 1.75 179.4
12 144 6.88 82.6 8.40...

Installation 13  
There is 3% ~ 5% tolerance among these numbers due to optical component limits.
* 1m = 3.28 feet,   1 feet = 0.305m,   1m = 100cm,   1 feet = 12 inches
Connecting to Various Equipment
HDTV Equipment
The projector is capable of displaying various High Definition TV display modes. Some of 
these sources are:  
Most of these sources will provide an analog component video output, a standard VGA 
output, or a YP
bPr (default) format. 
The projector is capable of accepting HDTV data through a...

Installation 14
Connecting to Various Equipment 
It only takes a few seconds to connect your projector to your desktop or notebook computer, 
VCR, or other systems. However, a Mac adapter (an optional accessory) is needed for 
connection to Macintosh computers.
A
C
 
IN
L
E
T
S-VIDEO     VIDEO               PC/HDT
V
PC/ HDTV S - Vi de o /  Vi de o
S-Video
Video 

Operation 15
Operation
Start Up
1. Plug the power cord into the projector and into a wall socket. 
2. Turn the main power switch on. 
3. Press and hold POWER  for 1 second to start the projector. The back-lit POWER key 
flashes green and stays green when the power is turned on.
(When the power is turned off, there is a 110-second cooling period before the projector can 
be re-started.)
4. Switch on all connected equipment.
AC INLET
S-VIDEO     VIDEO               PC/HDTV 

Operation 16
Digital Keystone Correction
Keystoning refers to the situation 
where the projected image is 
noticeably wider at either the top or 
bottom. To correct this, press 3 
Left/ Right 4 (hot key) on the 
control panel of the projector or 
KEYSTONE 3/4 on the remote 
control, and then adjust the sliding 
bar labeled Keystone, as needed. 
Press + to correct keystoning at the 
top of the image. Press - to correct 
keystoning at the bottom of the 
image.
Auto Adjustment
In some cases, you may need to...