BenQ Mx763/mx764 Digital Projector User Manual

Operation 31
Optimizing the image
Using Wall Color
In the situation where you are projecting onto a colored surface such as a painted wall which 
may not be white, the Wall Color feature can help correct the projected picture’s colors to 
prevent possible color difference between the source and projected pictures.
To use this function, go to the DISPLAY > Wall Color menu and press  /  to select a 
color which is closest to the color of the projection surface. There are several precalibrated 
colors to...

Operation 328. The confirmation message “Setting Saved” is displayed.
Fine-tuning the image quality in user modes
According to the detected signal type, there are some user-definable functions available 
when User 1 or User 2 is selected. Based on your needs, you can make adjustments to these 
functions by highlighting them and pressing  /  on the projector or remote control.
Adjusting Brightness
The higher the value, the brighter the image. And the 
lower the setting, the darker the image. Adjust this...

Operation 33 In most installation situations, color management will not be necessary, such as in 
classroom, meeting room, or lounge room situations where lights remain on, or where 
building external windows allow daylight into the room. 
Only in permanent installations with controlled lighting levels such as boardrooms, lecture 
theaters, or home theaters, should color management be considered. Color management 
provides fine color control adjustment to allow for more accurate color reproduction,...

Operation 348. Make sure you have made all of the desired adjustments.
9. Press MENU/EXIT to exit and save the settings.
Setting the presentation timer
Presentation timer can indicate the presentation time on the screen to help you achieve 
better time management when giving presentations. Follow these steps to utilize this 
function:
1. Go to the SYSTEM SETUP: Basic > Presentation Timer menu and press MODE/
ENTER to display the Presentation Timer page.
2. Highlight Timer Period and decide the time...

Operation 35
Remote paging operations
Connect the projector to your PC or notebook with a USB cable prior to using the paging 
function. See Connection on page 17 for details.
You can operate your display software program (on a connected PC) which responds to page 
up/down commands (like Microsoft PowerPoint) by pressing PAGE UP/PAGE DOWN on 
the remote control.
If remote paging function doesnt work, check if the USB connection is correctly made and 
the mouse driver on your computer is updated to the...

Operation 36
Locking control keys
With the control keys on the projector locked, you can prevent your projector settings from 
being changed accidentally (by children, for example). When the Panel Key Lock is on, no 
control keys on the projector will operate except  POWER.
1. Go to the SYSTEM SETUP: Basic > Panel Key Lock menu, and select On by pressing 
/  on the projector or remote control. A confirmation message is displayed. 
2. Highlight Ye s and press MODE/ENTER to confirm.
To release panel key...

Operation 37 4. If the action is successful, you see the message Captured Succeeded on the screen. The 
captured picture is saved as My Screen.
5. To view the captured picture displayed as the startup screen, set My Screen in the 
SYSTEM SETUP: Basic > Splash Screen menu and restart the projector.
•  Using the OSD menu
1. Press MENU/EXIT and then press  /  until the SYSTEM SETUP: Basic menu is 
highlighted.
2. Press   to highlight My Screen and press MODE/ENTER.
3. Repeat steps 2-5 in the Using the...

Operation 38
Controlling the projector through a LAN 
environment
You can manage and control the projector from one or more remote computers when they 
are properly connected to the same local area network.
Cable connection
If you are in a DHCP environment:
1. Take a RJ45 cable and connect one end to the RJ45 LAN input jack of the projector 
and the other end to the RJ45 port on your Ethernet or router.
2. Do one of the following: 
•Press NETWORK SETTING on the remote control. The Network Settings page...

Operation 39
Wireless connection
To connect to the projector wirelessly, you have to plug a BenQ wireless dongle (optional) to 
the USB Type A connector on the projector, and then only a few OSD configuration steps are 
required.
1. Make sure the projector is turned on.
2. Do one of the following: 
•Press NETWORK SETTING on the remote control. The Network Settings page 
is displayed. 
•Press MENU/EXIT and then press  /  until the SYSTEM SETUP: Advanced 
menu is highlighted. Press   to highlight Network...

Operation 404. Click Search in the SSID row to list all the available wireless access points. Click the 
desired SSID in the Search result list and click Apply. 
5. Disconnect the RJ45 cable from the computer.
6. Select the same SSID from your computer.
7. Open QPresenter and search for the correct projector and click Connect.
• See Using QPresenter on page 49 for how to connect the projector.
•  There are more wireless settings available on the Projector Network display System > 
Admin > Wireless LAN...