BenQ Mw712 Users Manual

							Downloaded from www.Manualslib.com manuals search engine Downloaded From projector-manual.com BenQ ManualsOperation41
Adjusting the sound level
To adjust the sound level, press Volume+/Volume- on the 
remote control, or :
1. Repeat steps 1-2 above.
2. Highlight VOLUME and select a desired sound level.
Turning off the Power on/off ring tone
To turn off the ring tone:
1. Repeat steps 1-2 in Muting the sound section.
2. Highlight Power on/off Ring Tone and select Off.
The only way to change Power on/off ring tone is setting On or Off here. Setting the sound mute 
or changing the sound level will not affect the Power on/off ring tone.
Personalizing the projector menu display
The On-Screen Display (OSD) menus can be set according to your preferences. The 
following settings do not affect the projection settings, operation, or performance. 
•Menu display time in the SYSTEM SETUP: Basic > Menu Settings menu sets 
the length of time the OSD will remain active after your last key press. The time length 
ranges from 5 to 30 seconds in 5-second increments. Use  /  to select a suitable 
time frame.
•Menu position in the SYSTEM SETUP: Basic > Menu Settings menu sets the 
OSD position in five locations. Use  /  to select a preferred position.
•Language in the SYSTEM SETUP: Basic menu sets your familiar language for the 
OSD menus. Use  /  to select your language. 
•Reminder Message in the SYSTEM SETUP: Basic > Menu Settings menu sets 
whether to display reminder messages on screen. Use  /  to select your desired 
setting.
•Splash Screen in the SYSTEM SETUP: Basic menu sets a preferred logo screen 
to be displayed during projector start-up. Use  /  to select a screen.  
						

							Downloaded from www.Manualslib.com manuals search engine Downloaded From projector-manual.com BenQ ManualsOperation 42
Select the lamp saver mode
• Using the remote control. 
Press Smart Eco and Highlight Lamp Mode and press  /  to select Normal/
Economic/Smart Eco.
•Using the OSD menu.
1. Press MENU/EXIT and then press  /  
until the SYSTEM SETUP: Advanced menu 
is highlighted.
2. Press  to highlight Lamp Mode and press 
MODE/ENTER. The Lamp Settings page 
displays.
3. Highlight Lamp Mode and press  /  to 
select Normal/Economic/Smart Eco. The lamp brightness vary from the 
different lamp mode,see the description list in table below.
•
If the Economic mode is selected, the light output will be reduced and result in darker 
projected pictures.
Use build-in test pattern
You can adjust the image shape and focus status by observing 
the input signal content, or using the test pattern build-in 
OSD manual from OSD for better observe the shape 
changed.
Open the OSD menu and go to the SYSTEM SETUP: 
Advanced > Test Pattern > On. Press MODE/ENTER. 
The Test Pattern displays.
Lamp ModeDescription
Normal100% lamp brightness.
Economic80% lamp power consumption.
Smart EcoThis is default setting. Lamp power consumption will save from 30% to 
100% dynamically by detecting the content brightness level.  
						

							Downloaded from www.Manualslib.com manuals search engine Downloaded From projector-manual.com BenQ ManualsOperation43
U s e  Te a c h i n g  Te m p l a t e
Making writing on the board easier for teachers, you can use build-in template by OSD.  
Open the OSD menu and go to the DISPLAY > 
Teaching Template . Choice Blackboard/ 
Whiteboard. >  Off/ Letter Formation/ Musical 
Staff/ Worksheet/ Coordinate Chart. The 
Teaching Template displays.
Teaching 
TemplateWhiteboardBlackboard
Letter 
Formation
Musical Staff
Worksheet
Coordinate 
Chart  
						

							Downloaded from www.Manualslib.com manuals search engine Downloaded From projector-manual.com BenQ ManualsOperation 44
Controlling the projector through a LAN 
environment
Network Settings allow you to manage the projector from a computer using a web 
browser when the computer and the projector are properly connected to the same local 
area network.
Configuring the Wired LAN Settings
If you are in a DHCP environment:
1. Take a RJ45 cable and connect one end to the LAN input jack of the projector and 
the other end to the RJ45 port.
2. Press MENU/EXIT and then press  /  until the SYSTEM SETUP: 
Advanced menu is highlighted.
3. Press  to highlight Network Settings and press MODE/ENTER. The 
Network Settings page displays.
4. Press  to highlight Wired LAN and press MODE/ENTER.
5. Press  to highlight DHCP and press  /  to select On.
6. Press  to highlight Apply and press MODE/ENTER.
7. Re-enter the Wired LAN page. The IP Address, Subnet Mask, Default 
Gateway, and DNS Server settings will be displayed. Note down the IP address.
If the IP Address still does not display, contact your ITS administrator.
If you are in a non-DHCP environment:
1. Repeat steps 1-4 above.
2. Press  to highlight DHCP and press  /  to select Off.
3. Contact your ITS administrator for information on the IP Address, Subnet Mask, 
Default Gateway, and DNS Server settings.
4. Press  to select the item you want to modify and enter the value.
5. Press  to highlight Apply and press MODE/ENTER.
Controlling the projector remotely through a web 
browser
Once you have configured the LAN settings, you can find the IP address for the projector 
in the bottom of the network screen. You can use any computer that is on the same local 
area network to control the projector.
Internet
IR Router  
						

							Downloaded from www.Manualslib.com manuals search engine Downloaded From projector-manual.com BenQ ManualsOperation45 1. Enter the address of the projector in the address bar of your browser and press 
Enter. For example: http://10.60.7.31
• The Crestron remote network operation page opens.
The Crestron page is only available when you are  on a Wired LAN network. It also allows 
you to control the projector remotely. The Crestron supports RoomView version 6.2.2.9.
i. These buttons function the same as the ones on the OSD menus or remote 
control. 
The Menu button can also be used to go back to previous OSD menu, exit and save menu 
settings.
ii. To switch input source, click on your desired signal.
i
i
i
ii  
						

							Downloaded from www.Manualslib.com manuals search engine Downloaded From projector-manual.com BenQ ManualsOperation 46The tools page allows you to manage the projector, configure the LAN control settings and 
secure access of remote network operation on this projector.
i. You can name the projector, keep track of its location and the person in charge 
of it.
ii. You can adjust the Wired LAN settings.
iii. Once set, access to the remote network operation on this projector has been 
password-protected.
iv. Once set, access to the tools page has been password-protected.
After making the adjustments, press the Send button and the data will be saved in the projector.
v. P re s s  exit to go back to the Crestron remote network operation page.
iii
iiiv
v
i  
						

							Downloaded from www.Manualslib.com manuals search engine Downloaded From projector-manual.com BenQ ManualsOperation47 The info page displays the information and status of this projector.
i. Press exit to go back to the Crestron remote network operation page.
i  
						

							Downloaded from www.Manualslib.com manuals search engine Downloaded From projector-manual.com BenQ ManualsOperation 48
Shutting down the projector
1. Press   on the projector. A confirmation 
message displays prompting you. 
If you dont respond in a few seconds, the 
message will disappear. If you use the remote 
control, press   to shut down the projector.
2. Press   on the projector a second time. The 
POWER indicator light flashes orange, the 
projection lamp shuts down, and the fans will 
continue to run to cool down the projector. 
To protect the lamp, the projector will not respond to 
any commands during the cooling process.
3. Once the cooling process finishes, the 
POWER indicator light is a steady orange 
and fans stop.
4. Disconnect the power cord from the power putlet if the projector will not be used 
in an extended period of time.
• If the projector is not properly shut down, to protect the lamp, when you attempt to re-start 
the projector, the fans will run for a few minutes to cool down. Press Power again to start 
the projector after the fans stop and the POWER indicator light turns orange.
• Actual lamp lives may vary due to different environmental conditions and usage.
Direct power off
The AC power cord can be pulled out right after the projector is turned off. To protect 
the lamp, wait about 10 minutes before re-starting the projector. (When you attempt to 
re-start the projector, the fans may run for a few minutes to cool down. In such cases, 
press   again to start the projector after the fans stop and the POWER indicator light 
turns orange.
II
II
II
II  
						

							Downloaded from www.Manualslib.com manuals search engine Downloaded From projector-manual.com BenQ ManualsOperation49
Menu operation
Menu system
Please note that the on-screen display (OSD) menus vary according to the signal type 
selected.
Main menu Sub-menu Options
1. 
DISPLAY
Wall ColorOff/Light Yellow/Pink/Light 
Green/Blue/Blackboard
Aspect Ratio Auto/Real/4:3/16:9/16:10
Keystone
Position
Phase
H. Size
Digital Zoom
3D SyncOff/Top-Bottom/
Frame sequential
3D Sync Invert On/Off
Teaching 
Te m p l a t eBlackboardOff/Letter Formation/
Musical Staff/Worksheet/
Coordinate Chart
WhiteboardOff/Letter Formation/
Musical Staff/Worksheet/
Coordinate Chart
2. 
PICTURE
Picture ModeDynamic/Presentation/sRGB/Cinema/User 1/
User 2
Reference Mode Dynamic/Presentation/sRGB/Cinema
Brightness
Contrast
Color
Tint
Sharpness
Brilliant Color On/Off
Color 
TemperatureCool/Normal/Warm
3D Color 
ManagementPrimary Color R/G/B/C/M/Y
Hue
Saturation
Gain
Save Settings
3. SOURCEQuick Auto Search On/Off
Color Space ConversionAuto/RGB/YUV  
						

							Downloaded from www.Manualslib.com manuals search engine Downloaded From projector-manual.com BenQ ManualsOperation 50
4. 
SYSTEM 
SETUP: 
Basic
Presentation TimerTimer period1~240 minutes
Timer displayAlways/Last 1 Min/Last 2 Min/
Last 3 Min/Never
Timer positionTop-Left/Bottom-Left/Top-Right/
Bottom-Right
Timer counting 
directionCount Down/Count Up
Sound reminder On/Off
On/Off Yes/No
Language
Projector PositionFront Table/Rear Table/Rear Ceiling/
Front Ceiling
Menu SettingsMenu display time5 sec/10 sec/15 sec/20 sec/25 sec/
30 sec
Menu positionCenter/Top-Left/Top-Right/
Bottom-Right/Bottom-Left
Reminder 
MessageOn/Off
Operation SettingsDirect Power On On/Off
Auto Power OffDisable/5 min/10 min/15 min/20 min/
25 min/30 min
Eco Blank TimerDisable/5 min/10 min/15 min/20 min/
25 min/30 min
Sleep TimerDisable/30 min/1 hr/2 hr/3 hr/4 hr/8 hr/
12 hr
Quick Cooling On/Off
Instant Restart On/Off
Signal Power On On/Off
Panel Key Lock On/Off Yes/No
Background ColorBenQ/Black/Blue/Purple
Splash ScreenBenQ/Black/Blue/MyScreen
MyScreenCaptureYes/No
Remote ReceiverFront+Top/Front/Top