BenQ Mw519 Users Manual

							Connection 21
Connecting a HDMI source device
The projector provides a HDMI input jack that allows you to connect it to a HDMI source 
device like a DVD player, a DTV tuner or a display.
HDMI (High-Definition Multimedia Interface) supports uncompressed video data 
transmission between compatible devices like DTV tuners, DVD players and displays over a 
single cable. It provides pure digital viewing and listening experience.
Examine your Video source device to determine if it has a set of unused HDMI output 
jacks available:
• If so, you can continue with this procedure.
• If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to a HDMI source device:
1. Take a HDMI cable and connect one end to the HDMI output jack of the HDMI 
source device. Connect the other end of the cable to the HDMI signal input jack on 
the projector. Once connected, the audio can be controlled by the projector On-
Screen Display (OSD) menus. See Audio Settings on page 55 for details..
2. Connect the other end of the HDMI cable to the HDMI jack on the projector.
• If the selected video image is not displayed after the projector is turned on and the correct 
video source has been selected, check that the Video source device is turned on and 
operating correctly. Also check that the signal cables have been connected correctly.
• In the unlikely event that you connect the projector to a DVD player via the projectors 
HDMI input and the projected picture displays wrong colors, please change the color space 
to YUV. See Changing Color Space on page 32 for details.
Downloaded From projector-manual.com BenQ Manuals 
						

							Connection 22
Connecting a Component Video source device
Examine your Video source device to determine if it has a set of unused Component Video 
output jacks available: 
• If so, you can continue with this procedure.
• If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to a Component Video source device:
1. Take a Component Video to VGA (D-Sub) adaptor cable and connect the end with 3 
RCA type connectors to the Component Video output jacks of the Video source 
device. Match the color of the plugs to the color of the jacks; green to green, blue to 
blue, and red to red.
2. Connect the other end of the Component Video to VGA (D-Sub) adaptor cable 
(with a D-Sub type connector) to the COMPUTER IN-1 or COMPUTER IN-2 
jack on the projector.
3. If you wish to make use of the projector speaker(s) in your presentations, take a 
suitable audio cable and connect one end of the cable to the audio output jack of the 
device, and the other end to the AUDIO jack of the projector.
• If the selected video image is not displayed after the projector is turned on and the correct 
video source has been selected, check that the Video source device is turned on and 
operating correctly. Also check that the signal cables have been connected correctly.
Downloaded From projector-manual.com BenQ Manuals 
						

							Connection 23
Connecting an S-Video/composite source device
Examine your Video source device to determine if it has an unused S-Video/composite 
output jack available: 
• If it has both jacks, use the S-Video output jack for connection as the S-Video terminal 
provides better picture quality than the Video terminal.
• If it has either of the output jack, you can also continue with this procedure.
• If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to an S-Video/Video source device:
1. Take an S-Video/Video cable and connect one end to the S-Video/Video output jack 
of the Video source device.
2. Connect the other end of the S-Video/Video cable to theS-Video/ Video jack on 
the projector.
3. If you wish to make use of the projector speaker(s) in your presentations, take a 
suitable audio cable and connect one end of the cable to the audio output jack of the 
device, and the other end to the AUDIO jack of the projector.
• If the selected video image is not displayed after the projector is turned on and the correct 
video source has been selected, check that the Video source device is turned on and 
operating correctly. Also check that the signal cables have been connected correctly.
Downloaded From projector-manual.com BenQ Manuals 
						

							Operation
24
Operation
Starting up the projector
1. Plug the power cord into the projector and into 
a power outlet. Turn on the power outlet switch 
(where fitted). Check that the POWER 
indicator light on the projector lights orange 
after power has been applied.
• Please use the original accessories (e.g. power cable) 
only with the device to avoid possible dangers such as 
electric shock and fire.
• If Direct power on function is activated in the SYSTEM SETUP: Basic > Operation Settings 
menu, the projector will turn on automatically after the power cord has been connected and 
power has been applied. See Direct Power On on page 54 for details. 
2. Remove the lens cap. If it is closed, it could 
become deformed due to the heat produced by 
the projection lamp.
3. Press  POWER on the projector or 
remote control to start the projector. The 
POWER indicator light flashes and stays 
green when the projector is on.
The start up procedure takes about 30 
seconds. In the later stage of start up, a 
startup logo is projected.
(If necessary) Rotate the focus ring to adjust 
the image clearness.
If the projector is still hot from previous activity, it will run the cooling fan for approximately 90 
seconds before energizing the lamp. 
4. If the projector is activated for the first time, 
select your OSD language following the on-
screen instructions.
5. If you are prompted for a password, press the 
arrow keys to enter a six digit password. See 
Utilizing the password function on page 29 
for details.
6. Switch all of the connected equipment on.
7. The projector will start to search for input 
signals. The current input signal being scanned 
displays in the screen. If the projector doesnt 
detect a valid signal, the message No Signal 
will continue displaying until an input signal is 
found.
II
Downloaded From projector-manual.com BenQ Manuals 
						

							Operation 25 You can also press Source on the projector or remote control to select your 
desired input signal. See Switching input signal on page 32 for details.
• If no signal is detected for 3 minutes, the projector automatically enters ECO BLANK 
mode.
Adjusting the projected image
Adjusting the projection angle
The projector is equipped with 1 quick-release adjuster foot and 1 rear adjuster foot. 
These adjusters change the image height and projection angle. To adjust the projector:
1. Press the quick-release button and lift the front 
of the projector. Once the image is positioned 
where you want it, release the quick-release 
button to lock the foot in position.
2. Screw the rear adjuster foot to fine tune the 
horizontal angle.
To retract the foot, hold up the projector while 
pressing the quick-release button, then slowly lower 
the projector. Screw the rear adjuster foot in a 
reverse direction.
If the projector is not placed on a flat surface or the screen and the projector are not 
perpendicular to each other, the projected image becomes trapezoidal. To correct this 
situation, see Magnifying and searching for details on page 33 for details.
• Do not look into the lens while the lamp is on. The strong light from the lamp may cause 
damage to your eyes.
• Be careful when you press the adjuster button as it is close to the exhaust vent where hot air 
comes from.
Auto-adjusting the image
In some cases, you may need to optimize the 
picture quality. To do this, press AUTO on the 
projector or remote control. Within 3 
seconds, the built-in Intelligent Auto 
Adjustment function will re-adjust the values of 
Frequency and Clock to provide the best 
picture quality.  
• The screen will be blank while Auto is 
functioning.
• This function is only available when PC signal (analog RGB) is selected.
Downloaded From projector-manual.com BenQ Manuals 
						

							Operation
26
Use build-in test pattern
You can adjust the image shape and focus 
status by observing the input signal content, or 
using the test pattern build-in OSD manual 
from OSD or remote control for better 
observe the shape changed.
Open the OSD menu and go to the SYSTEM 
SETUP: Advanced > Test Pattern > On. 
Press MODE/ENTER. The Test Pattern 
displays.
Fine-tuning the image size and clarity
1. Adjust the projected image to the size that 
you need using the zoom ring.
2. Then sharpen the image by rotating the 
focus ring.
Downloaded From projector-manual.com BenQ Manuals 
						

							Operation 27
Correcting keystone
Keystoning refers to the situation where the projected image is noticeably wider at either 
the top or bottom. It occurs when the projector is not perpendicular to the screen. 
To correct this, besides adjusting the height of the projector, you will need to manually 
correct it following one of these steps.
• Using the remote control
Press  /  on the projector or remote 
control to display the Keystone correction page. 
Press   to correct keystoning at the top of the 
image. Press   to correct keystoning at the 
bottom of the image.
•Using the OSD menu
1. Press MENU/EXIT and then press  /  
until the 
DISPLAY menu is highlighted.
2. Press  to highlight Keystone and press 
MODE/ENTER. The Keystone correction 
page displays.
3. Press   to correct keystoning at the top 
of the image or press   to correct 
keystoning at the bottom of the image.
Press /.Press /.
Downloaded From projector-manual.com BenQ Manuals 
						

							
Operation
28
Using the menus
The projector is equipped with On-Screen Display (OSD) menus for making various 
adjustments and settings.
Below is the overview of the OSD menu.
The following example describes how to set the OSD language.
1. Press  MENU/EXIT  on the projector 
or remote control to turn the OSD 
menu on. 3. Press  to highlight 
Language  and press Enter to 
select a preferred language .
2. Use  /  to highlight the  SYSTEM 
SETUP: Basic  menu. 4. Press
 MENU/EXIT  twice* on 
the projector or remote 
control to leave and save the 
settings.
*The first press leads you back to 
the main menu and the second 
press closes the OSD menu.
Current input signal
Main menu icon
Main menu
Sub-menu
Highlight
Press  MENU/
EXIT  to the 
previous page 
or to exit. Status
Downloaded From projector-manual.com BenQ Manuals 
						

							
Operation 29
Securing the projector
Using a security cable lock
The projector has to be installed in a safe place to prevent theft. Otherwise, purchase a 
lock, such as the Kensington lock, to secure  the projector. You can locate a Kensington 
lock slot on the rear side of the projector. See item 17 on page  9 for details.
A Kensington security cable lock is usually a  combination of key(s) and the lock. Refer to 
the locks documentation for  finding out how to use it.
Utilizing the password function
For security purposes and to help prevent una uthorized use, the projector includes an 
option for setting up password security. The password can be set through the On-Screen 
Display (OSD) menu.
WARNING: You will be inconvenienced if you  activate the power-on lock functionality and 
subsequently forget the password. Print out this  manual (if necessary) and write the password 
you used in this manual, and keep the ma nual in a safe place for later recall.
Setting a password
Once a password has been set, the projector  cannot be used unless the correct password is 
entered every time the projector is started.
1. Open the OSD menu and go to the  SYSTEM SETUP: Advanced > Security 
Settings  menu. Press  MODE/ENTER . The Security Settings  page displays.
2. Highlight  Power on lock  and select On by pressing  / .
3. As pictured to the right, the four arrow keys 
( ,  ,  ,  ) respectively represent 4 digits 
(1, 2, 3, 4). According to the password you 
desire to set, press the arrow keys to enter six 
digits for the password.
4. Confirm the new password by re-entering the  new password.
Once the password is set, the OSD menu 
returns to the  Security Settings  page.
IMPORTANT: The digits being input will display  as asterisks on-screen. Write your selected 
password down here in this manual in advance or  right after the password is entered so that it is 
available to you should you ever forget it.
Password: __ __ __ __ __ __
Keep this manual in a safe place.
5. To leave the OSD menu, press  MENU/EXIT.
Downloaded From projector-manual.com BenQ Manuals 
						

							
Operation
30
If you forget the password
If the password function is activated, you will be asked 
to enter the six-digit password every time you turn on 
the projector. If you enter the wrong password, the 
password error message as pictured to the right 
displays lasting for three seconds, and the message 
INPUT PASSWORD  follows. You can retry by 
entering another six-digit password, or if you did not 
record the password in this manual, and you absolutely do not remember it, you can use 
the password recall procedure. See  Entering the password recall procedure on page 30  
for details.
If you enter an incorrect password 5 times in succession, the projector will automatically 
shut down in a short time.
Entering the password recall procedure
1. Press and hold  Auto on the projector or 
remote control for 3 seconds. The projector 
will display a coded number on the screen.
2. Write down the number and turn off your  projector.
3. Seek help from the local BenQ service center to  decode the number. You may be required to 
provide proof of purchase documentation to 
verify that you are an authorized user of the 
projector.
Changing the password
1. Open the OSD menu and go to the  SYSTEM SETUP: Advanced > Security 
Settings  > Change Password  menu.
2. Press  MODE/ENTER . The message INPUT CURRENT PASSWORD  displays.
3. Enter the old password.
• If the password is correct, another message  INPUT NEW PASSWORD 
displays. 
• If the password is incorrect, the password error message displays lasting for three  seconds, and the message  INPUT CURRENT PASSWORD  displays for 
your retry. You can press  MENU/EXIT to cancel the change or try another 
password.
4. Enter a new password.
IMPORTANT: The digits being input will display  as asterisks on-screen. Write your selected 
password down here in this manual in advance or  right after the password is entered so that it is 
available to you should you ever forget it.
Password: __ __ __ __ __ __
Keep this manual in a safe place.
5. Confirm the new password by re-entering the new password.
Downloaded From projector-manual.com BenQ Manuals