BenQ Mp612 Dlp Users Manual

							Maintenance 51
Maintenance
Care of the projector
Your projector needs little maintenance. The only thing you need to do on a regular basis is 
to keep the lens clean.
Never remove any parts of the projector except the lamp. Contact your dealer if other parts 
need replacing.
Cleaning the lens
Clean the lens whenever you notice dirt or dust on the surface. 
• Use a canister of compressed air to remove dust. 
• If there is dirt or smears, use lens-cleaning paper or moisten a soft cloth with lens cleaner 
and gently wipe the lens surface.
Never rub the lens with abrasive materials.
Cleaning the projector case
Before you clean the case, turn the projector off using the proper shutdown procedure as 
described in Shutting down the projector on page 40 and unplug the power cord.
• To remove dirt or dust, wipe the case with a soft, lint-free cloth.
• To remove stubborn dirt or stains, moisten a soft cloth with water and a neutral pH 
detergent. Then wipe the case.
Never use wax, alcohol, benzene, thinner or other chemical detergents. These can damage the 
case.
Storing the projector
If you need to store the projector for an extended time, please follow the instructions below:
• Make sure the temperature and humidity of the storage area are within the 
recommended range for the projector. Please refer to Specifications on page 59 or 
consult your dealer about the range.
• Retract the adjuster feet.
• Remove the batteries from the remote control.
• Pack the projector in its original packing or equivalent.
Transporting the projector
It is recommended that you ship the projector with its original packing or equivalent.
Downloaded From projector-manual.com BenQ Manuals 
						

							Maintenance 52
Lamp information
Calculation of lamp hour
When the projector is in operation, the duration (in hours) of lamp usage is automatically 
calculated by the built-in timer. The method of calculating the equivalent lamp hour is as 
follows:
Total (equivalent) lamp hour
= 1 (hours used in Economic mode) + 4/3 (hours used in normal mode)
See Lamp mode (Normal) on page 49 for more information on Economic mode.
The lamp hour in Economic mode is calculated as 3/4 of that in normal mode. That is, using 
the projector in Economic mode helps to extend the lamp hour by 1/3.
Warning message
When the Lamp indicator lights up red or a message appears suggesting it is time to replace 
the lamp, please install a new lamp or consult your dealer. An old lamp may cause a 
malfunction in the projector and in some instances the lamp may explode.
The Lamp indicator light and Temperature warning light will light up if the lamp becomes too 
hot. Turn the power off and let the projector cool for 45 minutes. If the Lamp or Temp indicator 
still lights up after turning the power back on, please contact your dealer. See Indicators on 
page 56 for details.
The following Lamp warning displays will remind you to change the lamp.
MessageStatus
The lamp has been in operation for 3000 hours. 
Install a new lamp for optimal performance. If the 
projector is normally run with Economic Mode 
selected (See Lamp mode (Normal) on page 49), 
you may continue to operate the projector until the 
3950 hour lamp warning appears. 
The lamp has been in operation for 3950 hours. A 
new lamp should be fitted to avoid the 
inconvenience when the projector runs out of lamp 
time.
OK
Order Replacement Lamp
Lamp > 3000 Hours
Notice
OK
Replace Lamp Soon 
Lamp > 3950 Hours
Notice
Downloaded From projector-manual.com BenQ Manuals 
						

							Maintenance 53
Replacing the lamp
• To reduce the risk of electrical shock, always turn the projector off and disconnect the 
power cord before changing the lamp.   
• To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes 
before replacing the lamp.
• To reduce the risk of injuries to fingers and damage to internal components, use caution 
when removing lamp glass that has shattered into sharp pieces.
• To reduce the risk of injuries to fingers and/or compromising image quality by touching 
the lens, do not touch the empty lamp compartment when the lamp is removed.
• This lamp contains mercury. Consult your local hazardous waste regulations to dispose of 
this lamp in a proper manner.
• To assure optimal performance from the projector, it is recommended that you purchase a 
BenQ projector lamp for lamp replacement.
• If lamp replacement is performed while the projector is suspended upside-down from the 
ceiling, make sure that no one is underneath the lamp socket to avoid any possible injury 
or damage to the human eyes caused by fractured lamp.
1. Turn the power off and disconnect the projector from the wall socket. If the lamp is 
hot, avoid burns by waiting for approximately 45 minutes until the lamp has cooled. The lamp has been in operation for 4000 hours. 
It is strongly recommended that you replace the 
lamp at this age. The lamp is a consumable item. 
The lamp brightness diminishes with use. This is 
normal lamp behavior. You can replace the lamp 
whenever you notice that the brightness level has 
significantly diminished. If the lamp is not 
replaced beforehand, it must be replaced after 3000 
hours usage.
The lamp MUST be replaced before the projector 
will operate normally.
OK
Replace Lamp Now 
Lamp > 4000 Hours
Lamp usage time exceeded
Notice
OK
Lamp-usage time exceeded
Replace lamp (refer to Users manual)
Then reset lamp timer
Notice
2. Turn the projector over. Then use a coin to 
turn the screw counterclockwise until the lamp 
cover loosens. 
Downloaded From projector-manual.com BenQ Manuals 
						

							Maintenance 543. Remove the lamp cover from the projector.
• Do not turn the power on with the lamp cover 
removed.
• Do not insert your fingers between the lamp and 
the projector. The sharp edges inside the 
projector may cause injuries.
4. Loosen the screw that secures the lamp.
5. Lift the handle so that it stands up. Use the 
handle to slowly pull the lamp out of the 
projector.
• Pulling it too quickly may cause the lamp to break 
and scatter broken glass in the projector.
• Do not place the lamp in locations where water 
might splash on it, children can reach it, or near 
flammable materials.
• Do not insert your hands into the projector after 
the lamp is removed. If you touch the optical 
components inside, it could cause color 
unevenness and distortion of the projected 
images.
6. As shown in the figure, lower the new lamp 
first into the connector on the projector and 
align the two holes on the projector.
7. Tighten the screw that secures the lamp.
• Loose screw may cause a bad connection, which 
could result in malfunction.
• Do not over tighten the screw.
8. Ensure the handle is fully laid flat and locked in 
place.
Downloaded From projector-manual.com BenQ Manuals 
						

							Maintenance 55 11. Restart the projector.
Do not turn the power on with the lamp cover removed. 
12. After the startup logo, open the On-Screen 
Display (OSD) menu. Go to the SYSTEM 
SETUP: Advanced > Lamp Settings menu. 
Press ENTER. The Lamp Settings page 
displays. Highlight Reset Lamp Timer. A 
warning message displays asking if you want 
to reset the lamp timer. Highlight Reset and 
press ENTER. The lamp time will be reset to 0.
Do not reset if the lamp is not new or replaced as this could cause damage. 
Temperature information
When the Temperature warning light is on, it is warning you of the following possible 
problems:
1. The internal temperature is too high.
2. The fans are not working.
Turn the projector off and contact qualified service personnel for further help. For more 
detailed information, please refer to Indicators on page 56. 9. Replace the lamp cover on the projector.
10. Use a coin to turn the screw clockwise until the 
lamp cover is secured. 
• Loose screw may cause a bad connection, which 
could result in malfunction.
• Do not over tighten the screw.
Reset Lamp Timer?
Reset
Cancel
Notice
Downloaded From projector-manual.com BenQ Manuals 
						

							Maintenance 56
Indicators
Illustration
•Blank -: Light OFF
•O: Orange light
•: Light flashing•R: Red light
•: Light ON•G: Green light
LightStatus & Description
PowerTe m pLamp
Power events
The projector has just been connected to a power outlet.
--Stand-by mode.
--Powering up.
--Normal operation.
--
1. The projector needs 90 seconds to cool down as it was 
abnormally shut down without the normal cooling down 
process. Or
2. The projector needs to cool for 90 seconds after the 
power is turned off.
--The projector has shutdown automatically. If you try to re-start 
the projector, it will shutdown again. Please contact your dealer 
for assistance.
Lamp events
-The projector has shutdown automatically. If you try to re-start 
the projector, it will shutdown again. Please contact your dealer 
for assistance.
--1. The projector needs 90 seconds to cool down. Or
2. Please contact your dealer for assistance.
  
  
O O O
O 
 G 
 G 
O 
O 
O  R
 R
Downloaded From projector-manual.com BenQ Manuals 
						

							Maintenance 57
LightStatus & Description
PowerTe m pLamp
Thermal events
--
The projector has shutdown automatically. If you try to re-start 
the projector, it w ill shutdow n again. Please contact your dealer 
for assistance.
-
-
-
-
 R
 R R
 R G
 RO
 R  R R
 R  R G
 R  RO
 G  R R
 G  R G
 G  RO
O  R R
O  R G
O  RO
 G R
 G G
Downloaded From projector-manual.com BenQ Manuals 
						

							Troubleshooting 58
Troubleshooting
The projector does not turn on.
No picture
Blurred image
Remote control does not work
The password is incorrect
CauseRemedy
There is no power from the power 
cable.Plug the power cord into the AC inlet on the 
projector, and plug the power cord into the 
power outlet. If the power outlet has a switch, 
make sure that it is switched on.
Attempting to turn the projector on 
again during the cooling process.Wait until the cooling down process has 
completed.
CauseRemedy
The video source is not turned on or 
connected correctly.Turn the video source on and check that the 
signal cable is connected correctly.
The projector is not correctly 
connected to the input source device.Check the connection.
The input signal has not been 
correctly selected.Select the correct input signal with the Source 
key on the projector or remote control.
The lens cover is still closed. Open the lens cover.
CauseRemedy
The projection lens is not correctly 
focused.Adjust the focus of the lens using the focus 
ring.
The projector and the screen are not 
aligned properly.Adjust the projection angle and direction as 
well as the height of the unit if necessary.
The lens cover is still closed. Open the lens cover.
CauseRemedy
The batteries are out of power. Replace the batteries with new ones.
There is an obstacle between the 
remote control and the projector.Remove the obstacle.
You are too far away from the 
projector.Stand within 8 meters (26 feet) of the 
projector.
CauseRemedy
You do not remember the password.Please see Entering the password recall pro-
cedure on page 28 for details.
Downloaded From projector-manual.com BenQ Manuals 
						

							Specifications 59
Specifications
Projector specifications 
All specifications are subject to change without notice. 
General
Product name Digital Projector Digital Projector
Model name MP612/MP612c MP622/MP622c
Optical
Resolution 800 x 600 SVGA 1024 x 768 XGA
Display system 1-CHIP DMD
Lens F/Number F=2.4 to 2.48, f= 20.7 to 22.8 mm
Lamp 200W lamp
Electrical
Power supply
AC100–240V, 3.1A, 50–60 Hz (Automatic)
Power consumption 285W (Max)
Mechanical
Dimensions 239 mm (W) x 106.3 mm (H) x 251 mm (D)
Weight 5.51 lbs (2.5 Kg)
Input terminal
Computer input
     RGB input D-sub 15-pin (female) x 1
Video signal input
     S-VIDEO Mini DIN 4-pin port x 1
     VIDEO RCA jack x1
HDTV signal input D-sub  Component RCA jack x3, through RGB input
Audio signal input
     Audio in Mini jack stereo port
Output
RGB output D-sub 15-pin (female) x 1
Speaker  (mixed mono) 2 watt x 1
Environmental Requirements
Operating temperature 0°C ~ 40°C at sea level
Operating relative humidity 10% ~ 90% (without condensation)
Operating altitude • 0–1499 m at 0°C–35°C
• 1500–3000 m at 0°C–30°C (with High Altitude Mode 
on)
Downloaded From projector-manual.com BenQ Manuals 
						

							Specifications 60
Dimensions
239 mm (W) x 106.3 mm (H) x 251 mm (D)
Unit: mm 
239
251
106.3
64.5 66.3
Downloaded From projector-manual.com BenQ Manuals