BenQ Mp612 Dlp Users Manual

							Connection 21
Connecting a monitor
If you want to view your presentation close-up on a monitor as well as on the screen, you 
can connect the RGB signal output socket on the projector to an external monitor with a 
VGA cable following the instructions below:
1. Connect the projector to a computer as described in Connecting a computer on page 
20.
2. Take a suitable VGA cable (only one supplied) and connect one end of the cable to the 
D-Sub input socket of the video monitor.
3. Connect the other end of the cable to the D-SUB OUT socket on the projector.
The final connection path should be like that shown in the following diagram:
The D-Sub output only works when an appropriate D-Sub input is made to the projector.
Laptop or desktop computer
VGA cable
VGA cable
Downloaded From projector-manual.com BenQ Manuals 
						

							Connection 22
Connecting Video source devices
You can connect your projector to various Video source devices that provide any one of the 
following output sockets:
• Component Video
•S-Video
•Video (composite)
You need only connect the projector to a Video source device using just one of the above 
connecting methods, however each provides a different level of video quality. The method 
you choose will most likely depend upon the availability of matching terminals on both the 
projector and the Video source device as described below:
Best video quality
The best available video connection method is Component Video (not to be confused with 
composite Video). Digital TV tuner and DVD players output Component Video natively, so 
if available on your devices, this should be your connection method of choice in preference 
to (composite) Video.
See Connecting a Component Video source device on page 23 for how to connect the 
projector to a component video device.
Better video quality
The S-Video method provides a better quality analog video than standard composite Video. 
If you have both composite Video and S-Video output terminals on your Video source 
device, you should elect to use the S-Video option.
See Connecting an S-Video source device on page 24 for how to connect the projector to 
an S-Video device.
Least video quality
Composite Video is an analog video and will result in a perfectly acceptable, but less than 
optimal result from your projector, being the least video quality of the available methods 
described here.
See Connecting a composite Video source device on page 25 for how to connect the 
projector to a composite Video device.
Connecting Audio
The projector has a built-in mono speaker which is designed to provide basic audio 
functionality accompanying data presentations for business purposes only. It is not designed 
for, nor intended for stereo audio reproduction use as might be expected in home theatre or 
home cinema applications. Any stereo audio input (if provided), is mixed into a common 
mono audio output through the projector speaker. 
If you have a separate sound system, you will most likely want to connect the audio output 
of your Video source device to that sound system, instead of to the mono audio projector. 
The audio connections illustrated in the following sections are provided for informational 
purposes only. You need not connect audio to the projector if there is an alternate sound 
system available, or if audio is not required.
Downloaded From projector-manual.com BenQ Manuals 
						

							Connection 23
Connecting a Component Video source device
Examine your Video source device to determine if it has a set of unused Component Video 
output sockets available: 
• If so, you can continue with this procedure.
• If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to a Component Video source device:
1. Take a Component Video to VGA (D-Sub) adaptor cable and connect the end with 3 
RCA type connectors to the Component Video output sockets of the Video source 
device. Match the color of the plugs to the color of the sockets; green to green, blue to 
blue; and red to red.
2. Connect the other end of the Component Video to VGA (D-Sub) adaptor cable (with 
a D-Sub type connector) to the D-SUB/COMP IN socket on the projector.
3. If you wish to make use of the projector (mixed mono) speaker, take a suitable audio 
cable and connect one end of the cable to the audio output socket of the computer, 
and the other end to the Audio socket of the projector.
The final connection path should be like that shown in the following diagram:
If you connect the projector to a High Definition TV (HDTV) tuner, the follow ing standards 
are supported:
• The projector is only capable of playing mixed mono audio, even if a stereo audio input is 
connected. See Connecting Audio on page 22 for details.
• Component Video is the only video output that delivers native 16:9 aspect ratio picture.
• If the selected video image is not displayed after the projector is turned on and the correct 
video source has been selected, check that the Video source device is turned on and 
operating correctly. Also check that the signal cables have been connected correctly.
• 480i • 480p
• 576i • 576p
• 720p (50/ 60 Hz) • 1080i (50/ 60 Hz)
Audio cables A/V device
Component Video to 
VGA (D-Sub) adaptor 
cable 
Downloaded From projector-manual.com BenQ Manuals 
						

							Connection 24
Connecting an S-Video source device
Examine your Video source device to determine if it has an unused S-Video output socket 
available: 
• If so, you can continue with this procedure.
• If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to an S-Video source device:
1. Take an S-Video cable and connect one end to the S-Video output socket of the Video 
source device.
2. Connect the other end of the S-Video cable to the S-VIDEO socket on the projector.
The final connection path should be like that shown in the following diagram:
• The projector is only capable of playing mixed mono audio, even if a stereo audio input is 
connected. See Connecting Audio on page 22 for details.
• If the selected video image is not displayed after the projector is turned on and the correct 
video source has been selected, check that the Video source device is turned on and 
operating correctly. Also check that the signal cables have been connected correctly.
• If you have already made a Component Video connection between the projector and this 
S-Video source device using Component Video connections, you need not connect to this 
device using an S-Video connection as this makes an unnecessary second connection of 
poorer picture quality. See Connecting Video source devices on page 22 for details.
A/V device
Audio cables
S-Video cable 
Downloaded From projector-manual.com BenQ Manuals 
						

							Connection 25
Connecting a composite Video source device
Examine your Video source device to determine if it has a set of unused composite Video 
output sockets available: 
• If so, you can continue with this procedure.
• If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to an composite Video source device:
1. Take a Video cable and connect one end to the composite Video output socket of the 
Video source device.
2. Connect the other end of the Video cable to the VIDEO socket on the projector.
The final connection path should be like that shown in the following diagram:
• The projector is only capable of playing mixed mono audio, even if a stereo audio input is 
connected. See Connecting Audio on page 22 for details.
• If the selected video image is not displayed after the projector is turned on and the correct 
video source has been selected, check that the Video source device is turned on and 
operating correctly. Also check that the signal cables have been connected correctly.
• You need only connect to this device using a composite Video connection if Component 
Video and S-Video inputs are unavailable for use. See Connecting Video source devices 
on page 22 for details.
A/V device
Audio cables
Video cable 
Downloaded From projector-manual.com BenQ Manuals 
						

							Operation 26
Operation
Start up
1. Plug the power cord into the projector and into a 
wall socket. Turn on the wall socket switch 
(where fitted). Check that the Power indicator 
on the projector lights orange after power has 
been applied.
2. Slide the lens cover open. If it is closed, it could 
become deformed due to the heat produced by the 
projection lamp.
3. Press Power on the projector or remote 
control to start the projector. As soon as the 
lamp lights up, a Power On Tone will be 
heard. The Power indicator light flashes green 
and stays green when the projector is on.
The start up procedure takes about 30 
seconds. In the later stage of start up, a startup 
logo is projected.
(If necessary) Rotate the focus ring to adjust 
the image clearness.
If the projector is still hot from previous activity, it will run the cooling fan for approximately 90 
seconds before energizing the lamp. 
4. If you are prompted for a password, press the arrow buttons to enter a six digit 
password. See Utilizing the power-on lock function on page 27 for details.
5. Switch all of the connected equipment on.
6. The projector will start to search for input signals. The current input source being 
scanned displays in the upper left corner of the screen. If the projector doesnt detect a 
valid signal, the No Signal message will continue displaying until an input source 
signal is found.
Yo u  c a n  a l s o  p r e s s  SOURCE on the projector or remote control to select your desired 
input signal. See Switching input signal on page 29 for details.
If the frequency/resolution of the input signal exceeds the projectors operating range, you will 
see the message Out of Range displayed on a blank screen. Please change to an input signal 
which is compatible with the projectors resolution or set the input signal to a lower setting. 
See Timing chart on page 61 for details.
II
Downloaded From projector-manual.com BenQ Manuals 
						

							Operation 27
Utilizing the power-on lock function
For security purposes and to help prevent unauthorized use, the projector includes an 
option for setting up password security. The password can be set through the On-Screen 
Display (OSD) menu. For details of the OSD menu operation, please refer to Using the 
menus on page 44.
WARNING: You will be inconvenienced if you activate the power-on lock functionality and 
subsequently forget the password. Print out this manual (if necessary) and write the password 
you used in this manual, and keep the manual in a safe place for later recall.
Setting a password
Once a password has been set, the projector cannot be used unless the correct password is 
entered every time the projector is started.
1. Open the OSD menu and go to SYSTEM SETUP: Advanced > Security Settings. Press 
Mode/enter. Highlight Power On Lock and select On by pressing Left or Right.
2. A prompt will display on the screen.
3. As pictured to the right, the four arrow 
buttons (Up, Right, Down, 
 Left) respectively represent 4 digits 
(1, 2, 3, 4). According to the password 
you desire to set, press the arrow 
buttons to enter six digits for the 
password.
Once the password is set, the OSD 
menu returns to the Security Settings 
page.
IMPORTANT: The digits being input will display as asterisks on-screen. Write your selected 
password down here in this manual in advance or right after the password is entered so that it 
is available to you should you ever forget it.
Password: __ __ __ __ __ __
Keep this manual in a safe place.
4. To leave the OSD menu, press Menu/exit.
If you forget the password
If the password function is activated, you will be asked 
to enter the six digit password every time you turn on 
the projector. If you enter the wrong password, the 
password error message as pictured to the right displays 
lasting for three seconds, and the INPUT PASSWORD 
message follows. You can retry by entering another six-
digit password, or if you did not record the password in 
this manual, and you absolutely do not remember it, you can use the password recall 
procedure. See Entering the password recall procedure on page 28 for details.
If you enter an incorrect password 5 times in succession, the projector will automatically 
shut down in a short time.
INPUT PASSWORD
Back MENU
Password Error
Please try again.
Downloaded From projector-manual.com BenQ Manuals 
						

							Operation 28
Entering the password recall procedure
Press and hold AU TO on the projector or remote 
control for 3 seconds. The projector will display a 
coded number on the screen. Write down the 
number and turn off your projector. Seek help 
from the local BenQ service center to decode the 
number. You may be required to provide proof of 
purchase documentation to verify that you are an 
authorized user of the projector.
Changing the password
1. Open the OSD menu and go to the SYSTEM SETUP: Advanced > Security Settings > 
Change Password menu.
2. Press Mode/enter. the message INPUT CURRENT PASSWORD displays.
3. Enter the old password.
i. If the password is correct, another message INPUT NEW PASSWORD displays. 
ii. If the password is incorrect, the password error message displays lasting for three 
seconds, and the message INPUT CURRENT PASSWORD displays for your 
retry. You can press Menu/exit to cancel the change or try another password.
4. Enter a new password.
IMPORTANT: The digits being input will display as asterisks on-screen. Write your selected 
password down here in this manual in advance or right after the password is entered so that it 
is available to you should you ever forget it.
Password: __ __ __ __ __ __
Keep this manual in a safe place.
5. Confirm the new password by re-entering the new password.
6. You have successfully assigned a new password to 
the projector. Remember to enter the new 
password next time the projector is started.
7. To leave the OSD menu, press MENU/exit.
Disabling the power-on lock function
To disable password protection, go back to the SYSTEM SETUP: Advanced > Security 
Settings > Power On Lock menu after opening the OSD menu system. Select Off by pressing 
Left or Right. The message INPUT PASSWORD displays. Enter the current 
password. 
i. If the password is correct, the OSD menu returns to the Security Settings page 
with Off shown in the row of Password. You will not have to enter the password 
next time when turning on the projector.
ii. If the password is incorrect, the password error message displays lasting for three 
seconds, and the message INPUT PASSWORD displays for your retry. You can 
press Menu/exit to cancel the change or try another password.
Though the password function is disabled, you need to keep the old password in hand should 
you ever need to re-activate the password function by entering the old password.
Please write down the recall code, 
and contact BenQ Customer 
Center.
Recall code:
0 2 1 2 RECALL PASSWORD
Exit
MENU
Password Changed
Downloaded From projector-manual.com BenQ Manuals 
						

							Operation 29
Switching input signal
The projector can be connected to multiple devices at the same time. However, it can only 
display one full screen at a time. 
Please decide if you want to activate the quick auto search function by performing the 
following steps.
1. Press Menu/exit on the projector or remote control to turn on the OSD menu.
2. Go to SOURCE > Quick Auto Search menu.
3. Press Left or Right on the projector or remote control to select On or Off.
4. Press MENU/exit to exit and save the settings.
• The brightness level of the projected image will change accordingly when you switch 
between different input signals. Data (graphic) PC presentations using mostly static 
images are generally brighter than Video using mostly moving images (movies).
The input signal type effects the options available for the Picture Mode. See Selecting a 
picture mode on page 33 for details.
• The native display resolution of this projector is in a 4:3 aspect ratio. For best display 
picture results, you should select and use an input source which outputs at this 
resolution. Any other resolutions will be scaled by the projector depending upon the 
aspect ratio setting, which may cause some image distortion or loss of picture clarity. 
See Selecting the aspect ratio on page 32 for details.
• After activating Quick Auto Search, the 
projector will perform automatic source 
search once you press SOURCE on the 
projector or remote control. 
i. Press SOURCE on the projector or 
remote control. A source selection bar 
displays. 
ii. Press Up or Down until your 
desired signal is selected and press 
Mode/enter.
iii. The projector will start automatic 
source search by detecting your selected 
signal first.
iv. The information of the first detected 
source will display at the upper left 
corner of the screen for 2 seconds.
• If you turn off Quick Auto Search, you can manually cycle through the available 
input sources by performing the following steps.
i. Press SOURCE on the projector or remote control. A source selection bar 
displays. 
ii. Press Up or Down until your desired signal is selected and press Mode/
enter.
iii. Once detected, the selected source information will display at the upper left 
corner of the screen for 2 seconds. If there is multiple equipment connected to 
the projector, you can press the button again to search for another signal.
D-Sub / Comp.
Video
S-Video
Downloaded From projector-manual.com BenQ Manuals 
						

							Operation 30
Adjusting the projected image
Adjusting the projection angle
The projector is equipped with 1 quick-release adjuster foot and 1 rear adjuster foot. These 
adjusters change the image height and projection angle. To adjust the projector:
1. Press the quick-release button and 
lift the front of the projector. Once 
the image is positioned where you 
want it, release the quick-release 
button to lock the foot in position.
Do not look into the lens while the lamp is 
on. The strong light from the lamp may 
cause damage to your eyes.
Be careful when you press the adjuster 
button as it is close to the exhaust vent 
where hot air comes from.
2. Screw the rear adjuster foot to fine tune the horizontal angle.
To retract the foot, hold up the projector while pressing the quick-release button, then 
slowly lower the projector. Screw the rear adjuster foot in a reverse direction.
If the projector is not placed on a flat surface or the screen and the projector are not 
perpendicular to each other, the projected image becomes trapezoidal. To correct this 
situation, adjust the value of Keystone in the DISPLAY menu, on the projector control panel, 
or remote control. See Correcting keystone on page 31 for details.
Auto-adjusting the image
In some cases, you may need to optimize the 
picture quality. To do this, press AU TO on the 
projector or remote control. Within 3 seconds, 
the built-in Intelligent Auto Adjustment function 
will re-adjust the values of Frequency and Clock 
to provide the best picture quality. 
The current source information will be displayed 
in the upper left corner of the screen for 3 
seconds. 
The screen will be blank while AUTO is 
functioning.
Fine-tuning the image size and clarity
1. Adjust the projected image to the size 
that you need using the zoom ring. 2. Then sharpen the image by rotating 
the focus ring. 
Downloaded From projector-manual.com BenQ Manuals