Home > BenQ > Projector > BenQ Mp611c Dlp Users Manual

BenQ Mp611c Dlp Users Manual

    Download as PDF Print this page Share this page

    Have a look at the manual BenQ Mp611c Dlp Users Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 702 BenQ manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							Operation 27
    Auto-adjusting the image
    In some cases, you may need to optimize the 
    picture quality. To do this, press AU TO on the 
    projector or remote control. Within 3 seconds, 
    the built-in Intelligent Auto Adjustment 
    function will re-adjust the values of Frequency 
    and Clock to provide the best picture quality. 
    The current source information will be displayed 
    in the lower right corner of the screen for 3 
    seconds. 
    The screen will be blank while AUTO is 
    functioning.
    Fine-tuning the image size and clarity
    Correcting keystone
    Keystoning refers to the situation where the projected image is noticeably wider at either the 
    top or bottom. It occurs when the projector is not perpendicular to the screen. 
    To correct this, besides adjusting the height of 
    the projector, you will need to manually correct 
    it following ONE of these steps.
    1. Press  Left3/Right 4 on the control panel of 
    the projector to display the status bar labelled 
    Keystone. Press Left 3 to correct keystoning at 
    the top of the image. Press Right4 to correct 
    keystoning at the bottom of the image.
    2. Press /  on the remote control to 
    display the status bar labelled Keystone, then 
    press  to correct keystoning at the top of the 
    image or press   to correct keystoning at the bottom of the image.
    3. Press 6 Menu on the projector or Menu on the remote control. Go to 
     Pro-
    Picture > Keystone
     and adjust the values by pressing Left 3/Right 4 on the projector or 
    Left 3/Right 4 on the remote control.
    1. Adjust the projected image to the size 
    that you need using the zoom ring. 2. Then sharpen the image by rotating 
    the focus ring. 
    Downloaded From projector-manual.com BenQ Manuals 
    						
    							Operation 28For example, 
    Selecting the aspect ratio
    The aspect ratio is the ratio of the image width to the image height. Most analog TV and 
    computers are in 4:3 ratio, which is the default for this projector, and digital TV and DVDs 
    are usually in 16:9 ratio.
    With the advent of digital signal processing, digital display devices like this projector can 
    dynamically stretch and scale the image output to a different aspect than that of the image 
    input source. 
    You can change the projected image ratio (no matter what aspect the source is) by entering 
     Pro-Picture >  Aspect Ratio. Select an aspect ratio to suit the format of the 
    video signal and your display requirements. There are three aspect ratios available:
    In the pictures below, the black portions are inactive areas and the white portions are active 
    areas.
    1.Native: The image is projected at its original aspect ratio, and resized to fit within the 
    display area. For input signals with lower resolutions, the projected image will display 
    smaller than if resized to full screen. You could adjust the zoom setting or move the 
    projector towards the screen to increase the image size if necessary. You may also need 
    to refocus the projector after making these adjustments.
    2.4:3: Scales an image so that it is displayed in the center of the screen 
    with a 4:3 aspect ratio. This is most suitable for 4:3 images like 
    computer monitors, standard definition TV and 4:3 aspect DVD 
    movies, as it displays them without aspect alteration.
    3.16:9: Scales an image so that it is displayed in the center of the screen 
    with a 16:9 aspect ratio. This is most suitable for images which are 
    already in a 16:9 aspect, like high definition TV, as it displays them 
    without aspect alteration.
    16:9 aspect ratio is only sourced through the Component Video input when 
    being fed an appropriate 16:9 aspect signal. See Connecting a Component Video source 
    device on page 20 and Obtaining a preferred projected image size on page 14 for details.
    0Keystone-6Keystone
    0Keystone+6Keystone
    1. Press Left 3 on the projector or
    2. Press  on the remote control or
    3. Press Left 3on the projector or 3 on the 
    remote control when you are in Picture --> 
    Keystone menu.
    1. Press Right 4 on the projector or
    2. Press  on the remote control or
    3. Press Right
     4 on the projector or 4 on 
    the remote control when you are in Picture -
    -> Keystone menu.
    Downloaded From projector-manual.com BenQ Manuals 
    						
    							Operation 29
    Selecting a picture mode
    The projector is preset with several predefined 
    application modes so that you can choose one to 
    suit your operating environment and input 
    source picture type. To select a operation mode 
    that suits your need, press MODE repeatedly 
    until your desired mode is selected. The picture 
    modes available for different types of signals are 
    listed below. 
    PC Signal Input
    1.Dynamic Mode (Default): Maximizes the 
    brightness of the projected image. This 
    mode is suitable for environments where extra-high brightness is required, such as 
    using the projector in well lit rooms.
    2.Presentation Mode: Is designed for presentations. The brightness is emphasized in this 
    mode to match PC and notebook coloring.
    3.sRGB Mode: Maximizes the purity of RGB colors to provide true-to-life images 
    regardless of brightness setting. It is most suitable for viewing photos taken with an 
    sRGB compatible and properly calibrated camera, and for viewing PC graphic and 
    drawing applications such as AutoCAD.
    4.Cinema Mode: Is appropriate for playing colorful movies, video clips from digital 
    cameras or DVs through the PC input for best viewing in a blackened (little light) 
    environment.
    5.Blackboard Mode: Is designed for educational use. Images are allowed to be projected 
    on a dark background, such as a blackboard instead of a normal screen. It is most 
    suitable for a well lit environment with a dark background for projection.
    YPbPr/S-Video/Video Signal Input
    1.Dynamic Mode: Is suitable for playing gamebox-based video games in a normal living 
    room lighting level environment.
    2.Standard Mode (Default): Is appropriate for viewing colorful movies, video clips 
    from digital cameras or DVs.
    3.Cinema Mode: Is suitable for enjoying dark movies or DVD movies best viewed in a 
    blackened (little light) home cinema or lounge room environment.
    4.Blackboard Mode: Is designed for educational use. Images are allowed to be projected 
    on a dark background, such as a blackboard instead of a normal screen. It is most 
    suitable for a well lit environment with a dark background for projection.
    Downloaded From projector-manual.com BenQ Manuals 
    						
    							Operation 30
    Hiding the image
    In order to draw the audience’s full attention to the 
    presenter, you can use BLANK to hide the screen 
    image. Press any key on the control panel to restore 
    the image. The word “BLANK” appears at the 
    lower right corner of the screen while the image is 
    hidden. When this function is activated with 
    video/S-video signal connected, the audio can still 
    be heard.
    You can set the blank time in the 
     
    Advanced > Blank Time 
    to let the projector 
    return the image automatically after a period of time when there is no action taken on the 
    blank screen. Note that once BLANK is pressed, the projector enters Economic mode 
    automatically.
    Do not block the projection lens from projecting as this could cause the blocking object to 
    become heated and deformed or even cause a fire.
    Creating your own startup screen-MyScreen 
    function
    In addition to selecting the projector preset startup screen from among BenQ logo, Black or 
    Blue screen, you can make your own startup screen by downloading pictures from your 
    computer to the projector.
    1. Connect the projector to a desktop computer via RS232 cable (optional accessory). See 
    Connecting a computer on page 17.
    2. Before download starts, be sure the projector has entered Standby Mode. Follow the 
    instruction below to enter Standby Mode:
    i. Plug AC power, and POWER, TEMP and LAMP LEDs on the projector will flash 
    orange and then go off at the same time.
    ii.POWER LED then turns solid orange.
    3. Insert the bundled CD into the CD drive of your computer. Click Install MyScreen 
    Wizard and follow the on-screen instructions to proceed.
    • Ensure you have sufficient privileges to install software.
    • MyScreen utility may not be compatible with Windows 98/ME or Windows 2000. We 
    recommend you to run MyScreen utility on Windows XP.
    Downloaded From projector-manual.com BenQ Manuals 
    						
    							Operation 31 4. To execute MyScreen utility:
    i. After MyScreen Wizard is successfully 
    installed, execute MyScreen utility by 
    selecting this icon   from 
    Program Files.
    ii. Click Next.
    iii. Click Next.
    iv. Click Browse to choose your desired 
    image and then click Next.
    v. Click MyScreen to begin download.
    Welcome to MyScreen Wizard!
    This wizard will guide you to have your own splash
              screen in BenQ projector.
    To continue, click "
    Next"
    Next
    Establish a connection to your BenQ projector
    Please connect your BenQ projector to a serial port on your computer 
               and be sure the projector is in standby mode.
    Found BenQ projector on COM1
    Confugure Serial Port Settings...
    To continue, click "Next"
    Next Back
    Back Next
    Choose an image to download to your BenQ projector
    Browse...
    Downloading to your BenQ projector
    Ready to download the new image as your splash screen?
                 Click MyScreen to begin.
    Back MyScreen
    Downloaded From projector-manual.com BenQ Manualr 
    						
    							Operation 32
    • Do not unplug the RS232 cable or close MyScreen Wizard window while downloading 
    image. Failing to do so will lead to immediate shutdown of the projector and MyScreen 
    utility. If this happens, unplug the power cord and plug it again to restart the download 
    process.
    Activating panel key lock
    To prevent unauthorized changes in the settings or accidental button pushes, panel key lock 
    can be activated to disable all panel key functions except POWER.
    Go to 
    Setting > Panel Key Lock, and select On by pressing Left3/Right4 on the 
    projector or remote control. A confirmation message displays. Press Down 6 to confirm or 
    press Up 5 to cancel.
    To release panel key lock, press and hold MENU6 
    on the projector for 5 seconds, or use the remote 
    control to enter 
    Setting > Panel Key 
    Lock
     and press Left3/Right4 to select OFF. A 
    confirmation message displays. Press Down 6 to 
    confirm or press Up 5 to cancel.
    • Buttons on the remote control are still in use 
    when panel key lock is enabled.
    • If you press POWER to turn off the projector 
    without disabling panel key lock, the projector will still be in locked status the next time it 
    is turned on.
    vi. Click Close after download finishes.
    • There are limitations on image formats.  
    *.bmp/*.jpg/*.png/*.gif files are acceptable, but 
    there is no guarantee that every image file can 
    be downloaded successfully. It depends on 
    the file size and the color form. 
    • If the image size is too large, as pictured to the 
    right, a warning message will show up after 
    download begins. Click Back to choose 
    another image and try again.
    MyScreen Download Finished!
    Please power on your projector then set MyScreen 
              as your default splash screen.
    Close
    Choose an image to download to your BenQ projector
    Browse...
    Back
    Error: Image size is too large.
      1. Please save it to be *.bmp file.
      2. File size less than 500K.
    Downloaded From projector-manual.com BenQ Manuals 
    						
    							Operation 33
    Setting the presentation timer
    Presentation timer can indicate the remaining presentation time on the screen to help you 
    achieve better time management when giving presentation. Follow these steps to utilize this 
    function: 
    1. Press 
    TIMER SETUP on the remote control to enter timer 
    setting directly or go to
    Setting > Presentation 
    Timer.
    2. Select On by pressing Left3/Right4. A confirmation 
    message displays. Press Down 6 to confirm or press Up 5 to 
    cancel.
    3. Press  6Down to go to the next option and decide the timer 
    period by pressing Left3/Right4.
    4. Press  6Down and choose if you want the timer to show up on the screen by pressing 
    Left3/Right4.
    5.If you select 
    Ye s, press  6Down to go to the next option and set the timer position as 
    in the upper left, upper right, lower left, or lower right corner by pressing Left3/
    Right4.
    6. Press  6Down and select your desired counting direction by pressing Left3/Right4.
    7. Press  6Down and decide if you want to activate sound reminder by pressing Left3/
    Right4. If you select 
    Ye s, a double beep sound will be heard at the last 30 seconds of 
    counting down/up, and a triple beep sound will be produced when the timer is up.
    TIMER On/Show on the remote control is a multifunctional key. If 
    the presentation timer is off, pressing this button for the first time 
    will activate timer and the second push on the button will display 
    timer on the screen. If the timer is already on, pressing this button 
    will display the timer on the screen. 
    • The duration of the on-screen timer is consistent with your timer 
    setting. For example, if you set the timer to always display, after 
    pressing this button for the first time to activate the timer, it will 
    remain on the screen. If you set the timer to never display, the 
    timer will only display on the screen for 5 seconds. Then it will 
    disappear. Please note the timer is still counting after hidden.
    • If the timer is already on, you need to reactivate the timer everytime a new timer period is 
    set.
    Freezing the image
    Press  Freeze on the remote control to freeze the image. An icon   
    will display in the lower right corner of the screen. To release the 
    function, press the Freeze button on the remote control, or the 
    Source button on the projector control panel. Note that pressing the 
    Source button will also change the input source.
    Even if an image is frozen on the screen, the pictures are running on 
    the video or other device. If the connected devices have active audio 
    output, you will still hear the audio even though the image is frozen.
    Downloaded From projector-manual.com BenQ Manuals 
    						
    							Operation 34
    Utilizing FAQ function
    Press and hold BLANK/Q? on the projector for 3 seconds 
    or go to 
     Advanced > FAQ. Possible solutions to 
    problems encountered by users regarding image quality, 
    installation, special feature operation and service 
    information are available to you. Use  Menu6/EXIT5  to 
    select one out of these four major categories. Press Left3/
    Right4 for more specific questions. Then press 3Left/
    4Right for possible solutions. To exit, press EXIT5. 
    Shutting down the projector
    1. Press Power and a prompt 
    message appears. Press Power 
    a second time to turn the 
    projector off. 
    2. The Power indicator light 
    flashes orange and the lamp 
    shuts down, the fans 
    continue to run for 
    approximately 30 seconds to 
    cool down the projector.
    To protect the lamp, the projector 
    will not respond to any commands 
    during the cooling process.
    3. Once the cooling process finishes, a 
    Power Off Ring Tone will be heard. 
    Disconnect the power cord from the 
    wall socket.
    • Do not unplug the power cord before the 
    projector shutdown sequence is 
    complete or during the 30-second 
    cooling down process.
    • If the projector is not properly shut 
    down, to protect the lamp, when you 
    attempt to re-start the projector, the fans 
    will run for a few minutes to cool down. Press Power again to start the projector after the 
    fans stop and the Power indicator light turns orange.
    Are You Sure to Power Off?
    Press Power Again to Power Off
    Downloaded From projector-manual.com BenQ Manuals 
    						
    							Operation 35
    Menu operation
    Menu system
    Please note that the on-screen display (OSD) menus vary according to the signal type 
    selected.
    *When a Video or S-Video signal is connected, the function is only available with NTSC 
    system selected.
    Functions available when receiving different signal types...
    Sub-MenuPCVideo / S-VideoComponent Video 
    Picture
    Picture Mode
    Color Temp
    Brightness
    ContrastPicture Mode
    Color Temp
    Brightness
    Contrast
    Color
    Tint*
    Sharpness
    Pro-Picture
    Keystone
    Auto Resize
    Aspect Ratio
    H Position
    V Position
    Phase
    H. SizeKeystone
    Auto Resize
    Aspect Ratio
    Setting
    Mute
    Vo l u m e
    OSD Time
    Blank Time
    Quick Cooling
    Panel Key Lock
    Password
    Change Password
    Reset
    Advanced
    Mirror
    Source Scan
    Language
    Splash Scre en
    High Altitude Mode
    Auto Off
    Economic Mode
    Presentation Timer
    FAQ
    Information
    Source
    Resolution
    Picture Mode
    Equivalent Lamp 
    HourSource
    System
    Picture Mode
    Equivalent Lamp 
    HourSource
    Resolution
    Picture Mode
    Equivalent Lamp 
    Hour
    Downloaded From projector-manual.com BenQ Manuals 
    						
    							Operation 36
    Using the menus
    The projector is equipped with on-screen display (OSD) menus for making various 
    adjustments and settings.
    There are 17 different menu languages. (Refer to page Advanced menu on page 41 for 
    more details.)
    The following example describes the adjustment of the keystone.
    1. Press MENU6 on the projector or 
    MENU on the remote control to turn 
    the on-screen menu on.4. Adjust keystone values by 
    pressing Left 3/Right 4on the 
    projector or Left 3/Right 4 on 
    the remote control.
    2. Use  Left3/Right 4 on the projector or 
    Left 3/Right 4on the remote control 
    to select the 
     Pro-Picture 
    menu.
    3. Press EXIT5 or MENU6 on the 
    projector or 6/5 on the remote 
    control to select Ke ystone.5. Press EXIT5 on the projector 
    or press Menu twice* on the 
    remote control to leave and save 
    the setting.
    *
    The first press leads you back to the 
    submenu and the second press closes 
    the on-screen menu.
    Auto Resize
    Aspect Ratio
    Keystone
    H Position
    V Position
    Phase
    H SizeOn
    Auto Resize
    Aspect Ratio
    Keystone
    H Position
    V Position
    Phase
    H SizeOn
    Auto Resize
    Aspect Ratio
    Keystone
    H Position
    V Position
    Phase
    H SizeOn
    Downloaded From projector-manual.com BenQ Manuals 
    						
    All BenQ manuals Comments (0)

    Related Manuals for BenQ Mp611c Dlp Users Manual