BenQ Mp512/mp513/mp522 Digital Projector User Manual

Maintenance 51 5. Pull out the lamp connector from a slot 
in the lamp compartment. Disconnect 
it from the projector as illustrated.
6. Lift the handle so that it stands up. Use 
the handle to slowly pull the lamp out 
of the projector.
• Pulling it too quickly may cause the lamp 
to break and scatter broken glass in the 
projector.
• Do not place the lamp in locations where 
water might splash on it, children can 
reach it, or near flammable materials.
• Do not insert your hands into the projector...

Maintenance 5213. Restart the projector.
Do not turn the power on with the lamp cover removed.
Resetting the lamp timer
14. After the startup logo, open the On-Screen 
Display (OSD) menu. Go to the SYSTEM 
SETUP: Advanced > Lamp Settings menu. 
Press Mode/Enter. The Lamp Settings page 
displays. Press   to highlight Reset lamp 
timer and press Mode/Enter. A warning 
message displays asking if you want to reset the lamp timer. Highlight Reset and press 
Mode/Enter. The lamp time will be reset to 0.
Do not...

Maintenance 53
Indicators
LightStatus & Description
PowerTe m pLamp
Power events
Orange Orange OrangeThe projector has just been connected to a power outlet.
Orange Off OffStand-by mode
Green
FlashingOff OffPowering up
Green Off OffNormal operation
Orange
FlashingOff Off
1. The projector needs 90 seconds to cool down as it was 
abnormally shut down without the normal cooling 
down process. Or
2. The projector needs to cool for 90 seconds after the 
power is turned off.
Orange
FlashingOff OffThe projector...

Troubleshooting 54
Troubleshooting
The projector does not turn on.
No picture
Blurred image
Remote control does not work
The password is incorrect
CauseRemedy
There is no power from the power 
cable.Plug the power cord into the AC inlet on the 
projector, and plug the power cord into the 
power outlet. If the power outlet has a switch, 
make sure that it is switched on.
Attempting to turn the projector on 
again during the cooling process.Wait until the cooling down process has 
completed.
CauseRemedy...

Specifications 55
Specifications
Projector specifications 
All specifications are subject to change without notice. 
General
Product name Digital Projector
Model name MP512 MP513 MP522
Optical
Resolution 800 x 600 SVGA 800 x 600 SVGA 1024 x 768 XGA
Display system 1-CHIP DMD
Lens F/Number F = 2.6, f = 22 mm F = 2.6 to 2.8, f = 21 
to 23 mmF = 2.6 to 2.8, f = 
21 to 23 mm
Lamp 185 W lamp 200 W lamp 185 W lamp
Electrical
Power supply AC100–240V, 3 A, 50/60 Hz (Automatic)
Power consumption 280 W (Max) 285 W...

Specifications 56
Dimensions
255 mm (W) x 90 mm (H) x 214 mm (D)
Timing chart
Supported timing for PC input
255
214
90
61.566
Resolution Horizontal 
Frequency 
(kHz)Ve r t ic a l 
Frequency 
(Hz)Pixel 
Frequency 
(MHz)Mode
640 x 48031.469 59.940 25.175 VGA_60
37.861 72.809 31.500 VGA_72
37.500 75.000 31.500 VGA_75
43.269 85.008 36.000 VGA_85
720 x 400 31.469 70.087 28.3221 720 x 400_70
800 x 60037.879 60.317 40.000 SVGA_60
48.077 72.188 50.000 SVGA_72
46.875 75.000 49.500 SVGA_75
53.674 85.061 56.250...

Specifications 57
Supported timing for Component-YPbPr input
Displaying a 1080i(1125i)@60Hz or 1080i(1125i)@50Hz signal may result in slight image 
vibration.
Supported timing for Video and S-Video inputs
Signal Format Horizontal Frequency 
(kHz)Vertical Frequency (Hz)
480i(525i)@60Hz 15.73 59.94
480p(525p)@60Hz 31.47 59.94
576i(625i)@50Hz 15.63 50.00
576p(625p)@50Hz 31.25 50.00
720p(750p)@60Hz 45.00 60.00
720p(750p)@50Hz 37.50 50.00
1080i(1125i)@60Hz 33.75 60.00
1080i(1125i)@50Hz 28.13 50.00
Video mode...

Warranty and Copyright information 58
Warranty and Copyright information
Limited warranty
BenQ warrants this product against any defects in material and workmanship, under normal 
usage and storage.
Proof of purchase date will be required with any warranty claim. In the event this product is 
found to be defective within the warranty period, BenQs only obligation and your exclusive 
remedy shall be replacement of any defective parts (labor included). To obtain warranty 
service, immediately notify the...

Regulation statements 59
Regulation statements
FCC statement
CLASS B: This equipment generates, uses and can radiate radio frequency energy and, if not 
installed and used in accordance with the instructions, may cause harmful interference to 
radio communications. However, there is no guarantee that interference will not occur in a 
particular installation. If this equipment does cause harmful interference to radio or 
television reception, which can be determined by turning the equipment off and on,...