BenQ Mp512/mp513/mp522 Digital Projector User Manual

Operation 31 6. Use the directional arrows ( ,  ,  ,  ) on the projector or remote control to 
navigate the picture.
7. To reduce size of the picture, press Mode/Enter to switch back to the zoom in/out 
functionality, and press AUTO to restore the picture to its original size. You can also 
press   repeatedly until it is restored to the original size.
The picture can only be navigated after the picture is magnified. You can further magnify the 
picture while searching for details.
Selecting the aspect...

Operation 324.16:9: Scales an image so that it is displayed in the 
center of the screen with a 16:9 aspect ratio. This is 
most suitable for images which are already in a 16:9 
aspect, like high definition TV, as it displays them 
without aspect alteration.
Optimizing the image
Selecting a picture mode
The projector is preset with several predefined 
picture modes so that you can choose one to suit 
your operating environment and input signal 
picture type.
To select a operation mode that suits your...

Operation 33
Setting the User 1/User 2 mode
There are two user-definable modes if the current available picture modes are not suitable 
for your need. You can use one of the picture modes (except the User 1/User 2) as a starting 
point and customize the settings.
1. Press Menu/Exit to open the On-Screen Display (OSD) menu.
2. Go to the PICTURE > Picture Mode menu.
3. Press  /  to select User 1 to User 2.
4. Press  to highlight Reference Mode.
This function is only available when User 1, or User 2 mode is...

Operation 34
Adjusting Color
Highlight Color in the PICTURE menu and adjust the values by pressing  / on the 
projector or remote control.
Lower setting produces less saturated colors. If the setting is too high, colors on the image 
will be overpowering, which makes the image unrealistic.
Adjusting Tint
Highlight Tint in the PICTURE menu and adjust the values by pressing  / on the 
projector or remote control.
The higher the value, the more reddish the picture becomes. The lower the value, the more...

Operation 35 Only in permanent installations with controlled lighting levels such as boardrooms, lecture 
theaters, or home theaters, should color management be considered. Color management 
provides fine color control adjustment to allow for more accurate color reproduction, 
should you require it.
Proper color management can only be achieved under controlled and reproducible viewing 
conditions. You will need to use a colorimeter (color light meter), and provide a set of 
suitable source images to...

Operation 36
Setting the presentation timer
The presentation timer can indicate the presentation 
time on the screen to help you achieve better time 
management when giving presentations. Follow these 
steps to utilize this function:
1. Press Timer Setup on the remote control or go to 
the SYSTEM SETUP: Basic > Presentation Timer 
menu and press Mode/Enter to display the 
Presentation Timer page.
2. Press  to highlight Timer period and decide 
the timer period by pressing  / . The length 
of time can be...

Operation 37
To cancel the timer, perform the following steps.
1. Go back to the Presentation Timer page. 
2. Press   and press  /  to highlight Off and press Mode/Enter. A confirmation 
message displays.
3. Highlight Yes and press Mode/Enter to confirm. You will see the message “Timer is 
Off” displaying on the screen.
How to use the TIMER On key?
Timer On is a multi-functional key.
• If the presentation timer is off, pressing this key 
displays a confirmation message. You can decide 
whether to...

Operation 38
• Keys on the remote control are still in use when panel key lock is enabled.
• If you press Power to turn off the projector without disabling panel key lock, the projector 
will still be in locked status the next time it is turned on.
Freezing the image
Press   on the remote control to freeze the image. 
The word FREEZE will display in the upper left 
corner of the screen. To release the function, press any 
key on the projector or remote control.
Even if an image is frozen on the screen,...

Operation 39 Operation under High Altitude Mode may cause a higher decibel operating noise level 
because of increased fan speed necessary to improve overall system cooling and 
performance.
If you use this projector under other extreme conditions excluding the above, it may display 
auto shut-down symptoms, which is designed to protect your projector from over-heating. 
In cases like this, you should switch to High Altitude mode to solve these symptoms. 
However, this is not to state that this projector...

Operation 40
Menu operation
Menu system
Please note that the on-screen display (OSD) menus vary according to the signal type 
selected.
Main menu Sub-menu Options
1. 
DISPLAY
Wall ColorOff/Light Yellow/Pink/Light 
Green/Blue/Blackboard
Aspect Ratio Auto/Real/4:3/16:9
Keystone
Position
Phase
H. Size
Digital Zoom
2. 
PICTURE
Picture ModePC source: Dynamic/Presentation/sRGB/Cinema/
User 1/User 2
Video source: Dynamic/Standard/Cinema/User 1/
User 2
Reference ModePC source: Dynamic/Presentation/sRGB/Cinema...