BenQ Fp92w User Manual

							  11   How to assemble your monitor hardware
How to detach the stand base
1. Prepare the monitor and area.
Turn off the monitor and the power before unplugging the 
power cable. Turn off the computer before unplugging the 
monitor signal cable.
Please be careful to prevent damage to the monitor. 
Placing the screen surface on an object like a stapler or a 
mouse will crack the glass or damage the LCD substrate 
voiding your warranty. Sliding or scraping the monitor 
around on your desk will scratch or damage the monitor 
surround and controls. 
Protect the monitor and screen by clearing a flat open area 
on your desk and placing a soft item like a towel on the 
desk for padding, before laying the screen face down on a 
flat clean padded surface.
2. Release the locking clip on one side of the stand base 
while pulling the edge of the base away from the 
stand arm.
3. Release the other locking clip to detach the stand base 
from the monitor stand arm.
 
						

							12  How to assemble your monitor hardware  
How to use the monitor wall mounting kit 
The back of your LCD monitor has a VESA standard mount with 100mm pattern, allowing the 
installation of a wall mount bracket. Before starting to install a monitor wall mounting kit, please 
read the precautions carefully.
Precautions:
•Install your monitor and monitor mounting kit on a wall with flat surface.
•Ensure that the wall material is stable to support the weight of the monitor.
•Turn off the monitor and the power before disconnecting the cables from the LCD monitor.
1. Remove the monitor base.
Lay the screen face down on a clean and well-padded sur-
face. Detach the monitor base as instructed in “
How to 
detach the stand base on page 11
.”
2. Remove the monitor stand.
Use a a cross-pointed screwdriver to release the screws that 
fixing the monitor stand to the monitor.
The use of a magnetic-head screwdriver is recommended 
to avoid of losing the screws.
Then pull the monitor stand backward away from the 
monitor.
In case you intend to use your monitor on the stand in 
the future, please keep the monitor base, monitor stand, 
and screws somewhere safe for future use.
 
						

							  13   How to assemble your monitor hardware
3. Remove the rear cover.
Slide the rear cover back toward you to remove it. The screw 
plate at the back of the monitor could be revealed. 
4. Follow the instruction manuals of the wall mount 
bracket you purchased to complete the installation.
 
						

							14  Getting the most from your BenQ monitor  
4. Getting the most from your BenQ monitor
To gain the most benefit from your new BenQ color LCD flat screen monitor, you should set the 
graphics card to the native resolution of 1440 x 900 at first, and then you may start to install the 
custom BenQ LCD Monitor driver software as provided on the BenQ LCD Monitor CD-ROM. 
The circumstances under which you connect and install your BenQ LCD Monitor will determine 
which process you need to follow to successfully install the BenQ LCD Monitor driver software. 
These circumstances relate to which version of Microsoft Windows you are using, and whether 
you are connecting the monitor and installing the software onto a new computer (without existing 
monitor driver software), or whether you are upgrading an existing installation (which already has 
existing monitor driver software) with a newer monitor. 
In either case however, the very next time you turn on your computer (after connecting the 
monitor to your computer), Windows will automatically recognise the new (or different) 
hardware, and will launch its Found New Hardware wizard. 
Follow the wizard instructions until it asks you to select a monitor model. At that point, click the 
Have Disk button, insert the BenQ LCD Monitor CD-ROM and select the appropriate monitor 
model. Further details and step-by-step instructions for both an automatic (new) or upgrade 
(existing) installation follow. See:
•How to install the monitor on a new computer on page 15. 
•How to upgrade the monitor on an existing computer on page 16 
If you require a User Name and Password to login to your Windows computer, you must be logged on as 
an Administrator or as a member of the Administrators group in order to install the monitor driver software. 
Furthermore, if your computer is connected to a network which has security access requirements, network 
policy settings may prevent you from installing software on your computer. 
 
						

							  15   Getting the most from your BenQ monitor
How to install the monitor on a new computer
This instruction details the procedure for selecting and installing the BenQ LCD Monitor driver 
software on a new computer which has never had a monitor driver installed before. This 
instruction is only suitable for a computer which has never been used before, and for which the 
BenQ LCD Monitor is the first ever monitor to be connected to it.
If you are adding the BenQ LCD Monitor to an existing computer that has already had another monitor 
connected to it (and has monitor driver software installed), you should not be following these instructions. 
You should instead be following the instructions for How to upgrade the monitor on an existing computer.
1. Follow the instructions in How to assemble your monitor hardware on page 8. 
When Windows (2000 or later) starts, it will automatically detect the new monitor and launch the 
Found New Hardware Wizard. Follow the prompts until it displays the option to Install Hardware 
Device drivers.
2. Insert the BenQ LCD Monitor CD-ROM into a CD drive on the computer.
3. Check Search for a suitable driver for my device option, and click Next.
4. Check the option for CD-ROM drives (uncheck all others) and click Next.
5. Look to confirm that the wizard has selected the correct name of your monitor as “BenQ 
FP92W” and click Next.
6. Click Finish.
7. Restart the computer.
 
						

							16  Getting the most from your BenQ monitor  
How to upgrade the monitor on an existing computer
This instruction details the procedure for manually updating the existing monitor driver software 
on your Microsoft Windows computer. It is currently tested as compatible (and recommended 
only) for Windows 2000 and Windows XP Operating System (OS). 
The BenQ LCD Monitor driver for your model may well function perfectly with other versions of Windows, 
however, as at the time of writing, BenQ has done no testing of this driver on other versions of Windows 
and cannot guarantee its operation on those systems.
Installing monitor driver software involves selecting an appropriate information file (.inf ) on the 
BenQ LCD Monitor CD-ROM for the particular model monitor you have connected, and letting 
Windows install the corresponding driver files from the CD. You need only steer it in the right 
direction. Windows has an Upgrade Device Driver Wizard to automate the task and guide you 
through the file selection and installation process. 
See:
•How to install on Windows XP system on page 17.
•How to install on Windows 2000 system on page 18.
 
						

							  17   Getting the most from your BenQ monitor
How to install on Windows XP system
1. Open Display Properties.
The quickest shortcut to Display Properties is through the Windows desktop. 
Right-click the desktop and select Properties from the popup menu.
Alternatively, the Windows menu to Display Properties is located in Control Panel. 
In Windows XP version, Control Panel is located directly under the main Start menu item. 
The menu options displayed will depend upon which type of view is selected for your system. 
•Under the Classic view, click Start | Control Panel | Display.
•Under the Category view, click Start | Control Panel | Appearance and Themes | Change the 
screen resolution.
The Display Properties window will display.
2. Click the Settings tab and the Advanced button. 
The Advanced Display Properties window will display.
3. Click the Monitor tab and select the ‘Plug and Play Monitor’ from the list.
If there is only one monitor in the list, it will already be selected for you.
4. Click the Properties button. 
The Monitor Properties window will display. 
If the driver provider is listed as BenQ, and the model matches that of your new monitor, the proper 
drivers are already installed, and you need do nothing further. Cancel out of these property windows.
However, if BenQ is not listed as the manufacturer, or the correct model is not currently shown, you 
will need to continue with these instructions.
5. Click the Driver tab and the Update Driver button.
The Hardware Update Wizard will display. Follow the wizard instructions noting the steps below:
6. Insert the BenQ LCD Monitor CD-ROM into a CD drive on the computer you attached the 
monitor to.
7. Check the option ‘Install from a list or specific location’ and click Next.
8. Check the option ‘Search for the best driver in these locations’ and also 
check ‘Search removable media’, then click Next.
Please wait while the wizard searches for drives and the BenQ LCD Monitor CD inserted in step 6. 
When complete, the wizard should have found and selected the BenQ driver on the CD appropriate to 
your monitor model, in this case ‘BenQ FP92W’ in the location ‘d:\driver\BenQFP92W.inf ’ or similar. 
The drive letter for your CD drive may differ from the example above depending upon your system – it 
may be ‘D:’ or ‘E:’ or ‘F:’ etc.
9. Select (single-click) the file named ‘BenQ FP92W’ on the CD, and click the Next button.
This will copy and install the appropriate monitor driver files to your computer.
10. Click Finish.
This will close the wizard and return you to the Monitor Properties window, now renamed BenQ 
FP92W Properties.
11. Click Close, OK, and OK.
This will close the Display Properties windows. You do not need to restart Windows XP, as the BenQ 
LCD monitor drivers will operate immediately with no further action required by you. 
 
						

							18  Getting the most from your BenQ monitor  
How to install on Windows 2000 system
You do not need to follow this instruction if you are installing onto a computer which has a Windows XP 
(or later) version system. In that case, see the instructions at How to install on Windows XP system on 
page 17.
1. Open Display Properties.
The quickest shortcut to Display Properties is through the Windows desktop. 
Right-click the desktop and select Properties from the popup menu.
Alternatively, the Windows menu to Display Properties is located in Control Panel.
In Windows 2000 version, Control Panel is located under the Settings menu item. 
Click Start | Settings | Control Panel | Display.
The Display Properties window will display.
2. Click the Settings tab and the Advanced button. 
The Advanced Display Properties window will display.
3. In Windows 2000, click the Monitor tab and the Properties button. 
The Monitor Properties window will display.
4. In Windows 2000, click the Driver tab and the Update Driver button. 
The Upgrade Device Driver Wizard will display.
See How to complete the Windows Upgrade Device Driver Wizard on page 19.
 
						

							  19   Getting the most from your BenQ monitor
How to complete the Windows Upgrade Device Driver Wizard
1. Load the BenQ LCD Monitor CD-ROM which came with your monitor.
Insert the CD-ROM into a CD drive on the computer you attached the monitor to.
The autorun User’s Guide language selection page will display in your web browser. 
You can select a language and view the online version of this manual from the next window. 
You could then print it out for reference if you wish to work off-line. When you’re ready, Cancel the 
browser as it is not required for the Windows Upgrade Device Driver Wizard.
2. Launch the Windows Upgrade Device Driver Wizard and click Next.
3. Check the option ‘Display a list of known drivers...’ and click Next.
4. Click the Have Disk button.
The Install From Disk window will display.
5. Click the Browse button and navigate to the BenQ LCD Monitor CD-ROM.
This is the CD you loaded in step 1 above. The CD Drive will have a Windows designated drive letter 
(like D: or E: or F:). Select the drive letter corresponding to the drive you put the CD into.
6. Double-click the folder labelled ‘Driver’.
The contents of the ‘Driver’ folder will display.
7. Click the Open button.
This will return you to the Install from Disk window, and it will have entered the address to the BenQ 
LCD Monitor CD ‘Driver’ folder into the field titled ‘Copy manufacturer’s files from:’.  
The field will contain something like
,“D:\Driver”, or “E:\Driver”, or “F:\Driver”.
8. Click the OK button.
This will return you to the Upgrade Device Driver Wizard.
9. Select (single-click) the file named BenQ FP92W, and click the Next button.
10. Click Next.
This will copy the appropriate monitor driver files to your computer.
11. Click Finish.
On Windows 2000, this will close the wizard and return you to the Monitor Properties window, now 
renamed ‘BenQ FP92W Properties’.
Should you wish to do so, this is where you can change the screen refresh rate and other monitor prop-
erties to suit your needs. See 
How to adjust the screen refresh rate on page 21 for details.
12. In Windows 2000, click Close.
This will close the BenQ FP92W Properties window and return you to the Advanced Display Proper-
ties window. 
13. In Windows 2000, click OK. 
This will close the Advanced Display Properties window, and return you to the Display Properties win-
dow. 
Should you wish to do so, this is where you can change the screen resolution (area and color). 
See 
How to adjust the screen resolution on page 20 for details.
14. Click OK.
This will close the Display Properties window, and if you made any changes to the screen resolution, 
Windows 2000 will prompt you for confirmation to effect the changes, and further confirmation to 
accept the changes. Click OK and Ye s respectively. 
 
						

							20  How to adjust the screen resolution  
5. How to adjust the screen resolution
Due to the nature of liquid crystal display (LCD) technology, the picture resolution is always fixed. 
The best possible picture for your FP92W is achieved with a resolution of 1440 x 900. This is called 
“Native Resolution” or maximal resolution – that is, the clearest picture. Lower resolutions are 
displayed on a full screen through an interpolation circuit. Image blurring across pixel boundaries 
can occur with the interpolated resolution depending upon the image type and its initial 
resolution.
To take full advantage of LCD technology you should select the native resolution setting of 1440 x 900 on 
your PC screen resolution setting as described below. Be aware that not all PC video cards provide this 
resolution value. If your doesnt, check with the video card manufacturers website for an updated driver 
for your particular model PC video card which supports this resolution. Software video drivers are often 
updated and available for new hardware video resolutions. If necessary, you may need to replace and 
update the PC video card hardware to be able to support the native resolution of the monitor.
1. Open Display Properties and select the Settings tab. 
Yo u  c a n  o p e n  Display Properties by right-clicking on the Windows desktop and selecting Properties 
from the pop-up menu.
2. Use the slider in the ‘Screen area’ section to adjust the screen resolution.
Select the recommended resolution of 1440 x 900 then click Apply.
If you select some other resolution, be aware that this other resolution is interpolated and may not 
accurately display the screen image as well as it could do at the native resolution setting.
3. Click OK then Ye s. 
4. Close the Display Properties window.