BenQ Dv3251 Users Manual

Section 1: Quick Start Guide 7
English
8. View the TV programs
Care and cleaning information
• Always turn off the display by pressing the power button before cleaning.
• Do NOT use cream, liquid, aerosol or spray cleaners. Use only a slightly damp well wrung-out (drip-free) and lint-free, clean soft  cloth and lightly wipe the display.
• If necessary, use a pH-neutral liquid dish -washing detergent diluted with water on a 
separate clean lint-free cloth to remove oil or grease marks. Wipe over again...

Section 1: Quick Start Guide
8
English

DV3251-En-QuickStartGuide.fm  Page 8  Tuesday, December 13, 200 5  2:03 PM
Downloaded From TV-Manual.com Manualr 

We l c o m e
English
V32S/DV3251/DV3253
LCD Display
Section 2: User’s Manual
DV3251-En.book  Page 9  Monday, December 12, 2005  4:07 PM
Downloaded From TV-Manual.com Manualr 

Getting to know your display
10
English
Getting to know your display
Introduction
This booklet is divided into two sections: the Quick Start Guide; and the User’s Manual. 
For details of the Quick Start Guide, see  1. Please read these instructions on page 2 . 
This is section 2, the Users Manual which describes how to customise the display settings so that 
you can gain the best viewing experience possible to suit your preferences and viewing 
environment. This section details the features  and...

Getting to know your display 11
English
Connecting other Graphic source inputs
You can connect a PC video card graphic source (if available) like an RGB output or a digital 
DVI output. If your device supports HDMI output, you can also use the HDMI input on the 
LCD display for connection. Select the  PC, DVI  or HDMI  input respectively to view the 
display. See  Connecting the PC input on page 23 , Connecting the DVI input on page 24  and 
Connecting the HDMI input on page 24 .
Display (front view)...

Getting to know your display
12
English
Display control panel
No.NameDescription
1  (Power) Toggles the display between standby mode and on. (Performs 
the same action as the 
Power button on the remote control.)
2 INPUT • Cycles through possible input signal sources. (Performs the 
same action as the  Input button on the remote control.)
• In the OSD (On-Screen Display) menu, selects the highlighted  menu item to enter a submenu. (Performs the same action as 
the  OK button on the remote control.)
3...

Getting to know your display 13
English
External AV devices (temporary) terminal panel
No.NameDescription
1 Headset socket This socket is an audio output for connecting an external 
headset
. The display speakers will be muted whenever the 
headset socket is being used.
2 AV 4  
(RCA or S-Video) • VIDEO (Composite video input):
Connect to the composite video output of your AV device.
• AUDIO (L/R audio inputs): Connect to the audio output of your AV device.
(This input is common for either Video or...

Getting to know your display
14
English
Display (rear view)
No.NameDescription
1 AC INLET Connect to the AC power cable 
2 HDMI Connect to a DVI digital video or HDMI digital audio/video output of 
your digital source device
3 PC AUDIO Connect to the audio output of either the PC or DVI digital video 
output as appropriate for your source device.
4 PC D-SUB Connect to a PCs RGB video (D-Sub) output. See 
Supported PC 
(D-Sub/DVI) Input Signal Timing on page 40  for compatible 
timing modes.
5 COMPONENT 2...

Getting to know your display 15
English10 AV3 AUDIO Connect to the audio output of either the Composite Video or S-
Video output as appropriate for your AV source device.
(These inputs are common for either Video or S-Video audio.)
11 ANTENNA Connect to your antenna TV/CATV cable system 
12 AV1 SCART
AV2 SCART Connect each to the SCART output of up to 2 separate AV source 
devices. AV1 is full SCART compliant and also accepts gaming 
RGB. AV2 is AV input SCART compliant and also accepts S-Video.
13 AUDIO...

Getting to know the remote control
16
English
Getting to know the remote control
1.  Power
Press this button to power the display on and off. See  Power 
on, power off and standby on page 18 .
2.  Input
Press this button to select a different input source. See 
Switching inputs on page 18 .
3.  Backlight
Press this button to select your desired screen backlight level.
See  Adjusting backlight on page 20 .
4.  Information
Press this button to display the screen image source 
information. See  Display...