BenQ Bl3201pt User Manual

  11   Getting to know your monitor
Connection
The following connection illustrations are for your reference only. For cables that are not 
supplied with your product, you can purchase them separately.
For detailed connection methods, see page 14 - 17. 
Speakers PC/Notebook
USB peripherals
(USB 2.0) SD card (*)
USB peripherals (USB 3.0)Adapter: 
DP to mini DP BL3200
*: Requires card reader driver for Windows 8.1 operating system. Install the driver from the supplied CD.
 

12  Getting to know your monitor  
Speakers PC/Notebook
USB peripherals
(USB 3.0) SD card (*)
USB peripherals (USB 3.0) BL3201
*: Requires card reader driver for Windows 8.1 operating system. Install the driver from the supplied CD.
 

  13   How to assemble your monitor hardware
How to assemble your monitor hardware
 • If the computer is turned on you must turn it off before continuing. 
Do not plug-in or turn-on the power to the monitor until instructed to do so.
• The following illustrations are for your reference only. The location and available input and output jacks may 
vary depending on the purchased model.
• The supported timing may vary by input signal. Refer to the Preset display modes section on the link 
Adjusting the...

14  How to assemble your monitor hardware  
Tighten the thumbscrew on the bottom of the monitor 
base as illustrated. And then turn the stand 
counterclockwise to face forward.
Orient and align the stand arm with the monitor ( ), 
push them together until they click and lock into place 
().
Gently attempt to pull them back apart to check that 
they have properly engaged.
Carefully lift the monitor, turn it over and place it 
upright on its stand on a flat even surface.
You should position the monitor and...

  15   How to assemble your monitor hardware
To Connect the DVI-D Cable
Connect the plug of the DVI-D cable (at the end 
without the ferrite filter) to the monitor video socket. 
Connect the other end of the cable (at the end with the 
ferrite filter) to the computer video socket.
Tighten all finger screws to prevent the plugs from 
accidently falling out during use.
Or
To Connect the HDMI Cable
Connect the plug of the HDMI cable to the HDMI port 
on the monitor. Connect the other end of the cable to...

16  How to assemble your monitor hardware  
3. Connect the audio cable.
Connect the audio cable between the socket on the 
rear of the monitor (Line In) and your computer audio 
outlet.
You may connect headphones to the headphone jack 
found on the back side of the monitor.
4. Connect USB devices.
Connect the USB cable between the PC and the 
monitor (via the upstream USB port at the back). This 
upstream USB port transmits data between the PC and 
the USB devices connected to the monitor.
Connect USB...

  17   How to assemble your monitor hardware
5. Connect the memory card.
Insert an SD, MMC, or MS memory card following the 
direction indicated on the card to exchange files.
Requires card reader driver for Windows 8.1 operating 
system. Install the driver from the supplied CD.
Supported memory card formats are as follows:
• SD / SDHC / SDXC
• MMC
• Memory Stick / Memory Stick Pro
• MS Duo / MS-Pro Duo
6. Connect the OSD Controller to the 
monitor.
Connect the OSD Controller to the mini USB port...

18  How to assemble your monitor hardware  
8. Organize the cables.
Attach the wire holder to its socket on the rear of the 
monitor. And insert the cables one after one into the 
wire holder ( ).
Route the cables via the cable management hole ( ).
9. Connect-to and turn-on the power.
Plug the other end of the power cord into a power 
outlet and turn it on.
Picture may differ from product supplied for your region.
Switch the power switch next to the AC power input 
jack to ON.
Turn on the monitor by...

  19   How to assemble your monitor hardware
How to detach the stand and the base
1. Prepare the monitor and area.
Turn off the monitor and the power before unplugging 
the power cable. Turn off the computer before 
unplugging the monitor signal cable.
Protect the monitor and screen by clearing a flat open 
area on your desk and placing a soft item like a towel on 
the desk for padding, before laying the screen face down 
on a flat clean padded surface.
Please be careful to prevent damage to the monitor....

20  How to assemble your monitor hardware  
Turn the stand counterclockwise until you cannot go 
further.
And then detach the base from the stand.