Belkin Router F6D6230xx4 User Manual

							29Double N+ Wireless Router
sectionstable of c ontents12346789105
alT e RN aTe s eTUP Me THoD
setting your Is P Connection Type to PPPo e
Most DSL providers use PPPoE as the connection type  . If you use a DSL modem to connect to the Internet, your ISP may use PPPoE to log you into the service . If you have an Internet connection in your home or small office that doesn’t require a modem, you may also use PPPoE  .
1�  User Name
This space is provided to type in your user name that was assigned by your ISP  . 
2�  Password
Type in your password and retype it into the “Retype Password” box to confirm it  .
3�  s ervice Name
A service name is rarely required by an ISP  . If you are not sure if your ISP requires a service name, leave this blank  . 
4�  MTU
The MTU setting should never be changed unless your ISP gives you a specific MTU setting  . Making changes to the MTU setting can cause problems with your Internet connection including disconnection from the Internet, slow Internet access, and problems with Internet applications working properly .
5�  Disconnect after X ���
The “Disconnect” feature is used to automatically disconnect the Router from your ISP when there is no activity for a specified period of time  . For instance, placing a check mark next to this option and entering “5” into the minute field will cause the Router to disconnect from the Internet after five minutes of no Internet activity . This option should be used if you pay for your Internet service by the minute  .
Your connection type is PPPoE if: 
1) Your ISP gave you a user name and password, which is required to connect to the Internet  .
2) Your ISP gave you software such as WinPOET or Enternet300 that you use to connect to the Internet  .
3) You have to double-click on a desktop icon other than your browser to get on the Internet .
(1)(2)
(3)
(4)
(5) 
						

							30Double N+ Wireless Router
sectionstable of c ontents12346789105
alT e RN aTe s eTUP Me THoD
setting your Internet  ser vice Provider (I sP) Connection Type to Point-to-Point Tunneling Protocol (PPTP) [European Countries Only]� 
Some ISPs require a connection using PPTP protocol, a type of connection most common in European countries  . This sets up a direct connection to the ISP’s system . Type in the information provided by your ISP in the space provided  . When you have finished, click “Apply Changes” (9) . After you apply the changes, the Internet Status indicator will read “connection OK” if your Router is set up properly  .
(1)(2)
(3)(4)
(5)(6)(7)
(8) 
						

							31Double N+ Wireless Router
sectionstable of c ontents12346789105
alT e RN aTe s eTUP Me THoD
1�  PPTP  account
Provided by your ISP  . Enter your PPTP account name here  .
2�  PPTP Password
Type in your password and retype it into the “Retype Password” box to confirm it  .
3�  Host Name
Provided by your ISP  . Enter your host name here  .  
The following becomes visible when you deselect “Get IP by DHCP”  .
4�  s er vice IP  address
Provided by your ISP  . Enter your service IP address here  . 
5�  My IP  address
Provided by your ISP  . Enter the IP address here  . 
6�  My subnet Mask
Provided by your ISP  . Enter the IP address here  .
7�  Default  gateway
Provided by your ISP  . If your ISP did not give you a connection ID (default gateway), leave this blank  .
8�  Disconnect after X…
The “Disconnect” feature is used to automatically disconnect the Router from your ISP when there is no activity for a specified period of time  . For instance, placing a check mark next to this option and entering “5” into the minute field will cause the Router to disconnect from the Internet after five minutes of no Internet activity . This option should be used if you pay for your Internet service by the minute  .  
						

							32Double N+ Wireless Router
sectionstable of c ontents12346789105
alT e RN aTe s eTUP Me THoD
setting your Connection Type if y ou are a Telstra® b igPond/optusNet Cable User
Australia Only] Follow the on-screen steps and click “Apply Changes” to complete your setup  . 
						

							33Double N+ Wireless Router
sectionstable of c ontents12346789105
alT e RN aTe s eTUP Me THoD
setting Custom Domain Name s erver (DNs) s ettings
A “Domain Name Server” is a server located on the Internet that translates Universal Resource Locaters (URLs) like “www  .belkin  .com” to IP addresses  . Many Internet Service Providers (ISPs) do not require you to enter this information into the Router  . The “Automatic from ISP” box (1) should be checked if your ISP did not give you a specific DNS address . If you are using a static IP connection type, then you may need to enter a specific DNS address and secondary DNS address for your connection to work properly  . If your connection type is dynamic or PPPoE, it is likely that you do not have to enter a DNS address . Leave the “Automatic from ISP” box checked  . To enter the DNS address settings, uncheck the “Automatic from ISP” box and enter your DNS entries in the spaces provided  . Click “Apply Changes” (2) to save the settings .
(1)
(2) 
						

							34Double N+ Wireless Router
sectionstable of c ontents12346789105
alT e RN aTe s eTUP Me THoD
Configuring your W aN Media a ccess Controller (Ma C) address 
All network components including cards, adapters, and routers, have a unique “serial number” called a MAC address  . Your Internet Service Provider (ISP) may record the MAC address of your computer’s adapter and only let that particular computer connect to the Internet service  . When you install the Router, its own MAC address will be “seen” by the ISP and may cause the connection not to work . Belkin has provided the ability to clone (copy) the MAC address of the computer into the Router . This MAC address, in turn, will be seen by the ISP’s system as the original MAC address and will allow the connection to work  . If you are not sure whether your ISP needs to see the original MAC address, simply clone the MAC address of the computer that was originally connected to the modem . Cloning the address will not cause any problems with your network  .  
Cloning your MaC  address 
To clone your MAC address, make sure that you are using the computer that was ORIGINALLY CONNECTED to your modem before the Router was installed  . Click the “Clone” button (1) . Click “Apply Changes” (3) . Your MAC address is now cloned to the Router  .
entering a s pecific MaC address
In certain circumstances you may need a specific WAN MAC address  . You can manually enter one in the “MAC Address” page . Type in a MAC address in the spaces provided (2) and click “Apply Changes” (3) to save the changes . The Router’s WAN MAC address will now be changed to the MAC address you specified  . 
(1)(2)
(3) 
						

							35Double N+ Wireless Router
sectionstable of c ontents1234578910
UsINg TH e Web- base D aDV aNC eD  Use R INT eR fa Ce 
6
Viewing the la N settings
Clicking on the header of the L AN tab (1) will take you to the L AN tab’s header page  . A quick description of the functions can be found here  . To view the settings or make changes to any of the L AN settings, click on “L AN Settings” (2) or to view the list of connected computers, click on “DHCP client list” (3) .
Changing laN settings
All settings for the internal L AN setup of the Router can be viewed and changed here  .
(1)(2)(3)(1)
(2)(3)
(4)
(5)
(6) 
						

							36Double N+ Wireless Router
sectionstable of c ontents12345789106
UsINg TH e Web- base D aDV aNC eD  Use R INT eR fa Ce 
1�  IP address
The “IP address” is the internal IP address of the Router  . The default IP address is “192 .168  .2  .1”  . To access the advanced setup interface, type this IP address into the address bar of your browser  . This address can be changed if needed . To change the IP address, type in the new IP address and click “Apply Changes”  . The IP address you choose should be a non-routable IP . Examples of a non-routable IP are:
192 .168  .x  .x (where x is anything between 0 and 255)
10  .x  .x  .x (where x is anything between 0 and 255)
2 �  s ubnet Mask 
There is no need to change the subnet mask  . This is a unique, advanced feature of your Belkin Router . It is possible to change the subnet mask if necessary; however, do NOT make changes to the subnet mask unless you have a specific reason to do so  . The default setting is “255 .255  .255  .0”  .
3�  DHCP s erver
The DHCP server function makes setting up a network very easy by assigning IP addresses to each computer on the network automatically  . The default setting is “On” . The DHCP server can be turned OFF if necessary; however, in order to do so you must manually set a static IP address for each computer on your network  . To turn off the DHCP server, select “Off” and click “Apply Changes” .
4�  IP Pool
The range of IP addresses set aside for dynamic assignment to the computers on your network  . The default is 2–100 (99 computers)  . If you want to change this number, you can do so by entering a new starting and ending IP address and clicking on “Apply Changes”  . The DHCP server can assign 100 IP addresses automatically . This means that you cannot specify an IP address pool larger than 100 computers  . For example, starting at 50 means you have to end at 150 or lower so as not to exceed the 100-client limit . The starting IP address must be lower in number than the ending IP address  .
5�  l ease Time 
The length of time the DHCP server will reserve the IP address for each computer  . We recommend that you leave the lease time set to “Forever”  . The default setting is “Forever”, meaning that any time a computer is assigned an IP address by the DHCP server, the IP address will not change for that particular computer . Setting lease times for shorter intervals such as one day or one hour frees IP addresses after the specified period of time . This also means that a particular computer’s IP address may change over time  . If you have set any of the other advanced features of the Router such as DMZ or client IP filters, these are dependent on the IP address . For this reason, you will not want the IP address to change . 
6�  l ocal Domain Name 
The default setting is “Belkin”  . You can set a local domain name (network name) for your network  . There is no need to change this setting unless you have a specific advanced need to do so  . You can name the network anything you want such as “MY NETWORK”  .  
						

							37Double N+ Wireless Router
sectionstable of c ontents12345789106
UsINg TH e Web- base D aDV aNC eD  Use R INT eR fa Ce 
Viewing the DHCP Client l ist Page
You can view a list of the computers (known as clients), which are connected to your network  . You are able to view the IP address (1) of the computer, the host name (2) (if the computer has been assigned one), and the MAC address (3) of the computer’s network interface card (NIC) . Pressing the “Reserve” button will tie up the assigned IP address to the current MAC address  . The “Reserved IP Database” section will show the linked IP and MAC addresses . Pressing the “Refresh” (4) button will update the list  . If there have been any changes, the list will be updated  .
The “Network Address” section defines the local IP address or range  . The “Subnet Mask and Gateway” section defines the mask and gateway for the addresses above .
(1)(2)(3)
(4) 
						

							38Double N+ Wireless Router
sectionstable of c ontents12345789106
UsINg TH e Web- base D aDV aNC eD  Use R INT eR fa Ce 
Configuring the Wireless Network  settings
The “Wireless” tab lets you make changes to the wireless network settings  . From this tab you can make changes to the wireless network name or Service Set Identifier (SSID), operating channel, encryption security settings, and configure the Router to be used as an access point .
Changing the Wireless Network Name ( ssID)
To identify your wireless network, a name called the SSID  is used  . The SSID is your network name . The default network name of the Router is “Belkin” followed by six digits that are unique to your Router  . Your network name will look something like “Belkin 123456” . You can change this to anything you choose, or you can leave it unchanged  . Keep in mind, if you decide to change your wireless network name, and there are other wireless networks operating in your area, your network name needs to be different from other wireless networks that may be operating in your area . To change the SSID, type in the SSID that you want to use in the SSID field (1) and click “Apply Changes” (2) . The change is immediate . If you make a change to the SSID, your wireless-equipped computers may also need to be reconfigured to connect to your new network name  . Refer to the documentation of your wireless network adapter for information on making this change  .
Note: Please periodically check for new Router firmware updates from the “Utilities > Firmware update” page . Newer firmware can fix problems, add wireless features, and/or improve wireless performance (see page 57)
(1)
(2)