Belkin Router F5D8236-4 User Manual
Have a look at the manual Belkin Router F5D8236-4 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 19 Belkin manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
29N Wireless Router sectionstable of c ontents1 234 6789105 alT e RN aTe seTUP MeTHod 9� Internet s ettings Shows the settings of the Internet/ WAN side of the Router that connects to the Internet. Changes to any of these settings can be made by clicking on the links or by clicking on the “Internet/ WAN” quick- navigation link on the left side of the screen. 10 � f eatures Shows the status of the Router’s firewall, and wireless features. Changes can be made to the settings by clicking on any one of the links or by clicking the quick-navigation links on the left side of the screen. 11 � Page Name The page you are on can be identified by this name. This User Manual will sometimes refer to pages by name. For instance “L AN > L AN Settings” refers to the “L AN Settings” page.s tep 4: Configuring your Router for Connection to your Internet service Provider (I sP) The “Internet/ WAN” tab is where you will set up your Router to connect to your Internet Service Provider (ISP). The Router is capable of connecting to virtually any ISP’s system provided you have correctly configured the Router’s settings for your ISP’s connection type. Your ISP connection settings are provided to you by your ISP. To configure the Router with the settings that your ISP gave you, click “Connection Type” (A) on the left side of the screen. Select the connection type you use. If your ISP gave you DNS settings, clicking “DNS” (B) allows you to enter DNS address entries for ISPs that require specific settings. Clicking “MAC Address” (C) will let you clone your computer’s MAC address or type in a specific WAN MAC address, if required by your ISP. When you have finished making settings, the “Internet Status” indicator will read “connection OK” if your Router is set up properly. (A) (B) (C)
30N Wireless Router sectionstable of c ontents1 234 6789105 alT e RN aTe seTUP MeTHod (2) (1) setting your Connection Type From the “Connection Type” page, you can select the type of connection you use. Select the type of connection you use by clicking the button (1) next to your connection type and then clicking “Next” (2). s etting your Internet service Provider (I sP) Connection Type to d ynamic IP A dynamic connection type is the most common connection type found with cable modems. Setting the connection type to “dynamic” in many cases is enough to complete the connection to your ISP. Some dynamic connection types may require a host name. You can enter your host name in the space provided if you were assigned one. Your host name is assigned by your ISP. Some dynamic connections may require that you clone the MAC address of the PC that was originally connected to the modem. 1 � Host Name (1) This space is provided to enter a host name that needs to be visible to your ISP. Enter your host name here and click “Apply Changes” (3). If your ISP did not assign you a host name, or you are not sure, leave this blank. 2 � Change W aN Ma C address (2) If your ISP requires a specific MAC address to connect to the service, you can enter a specific MAC address or clone the current computer’s MAC address through this link. (2) (1) (3)
31N Wireless Router sectionstable of c ontents1 234 6789105 alT e RN aTe seTUP MeTHod setting your Internet service Provider (I sP) Connection Type to static IP A static IP address connection type is less common than other connection types. If your ISP uses static IP addressing, you will need your IP address, subnet mask, and ISP gateway address. This information is available from your ISP or on the paperwork that your ISP left with you. Type in your information, then click “Apply Changes” (4). After you apply the changes, the Internet Status indicator will read “Connected” if your Router is set up properly. 1 � IP address (1) Provided by your ISP. Enter your IP address here. 2 � s ubnet Mask (2) Provided by your ISP. Enter your subnet mask here. 3 � Is P g ateway a ddress (3) Provided by your ISP. Enter the ISP gateway address here. (1)(2)(3) s etting your I sP Connection Type to PPPo e Most DSL providers use PPPoE as the connection type. If you use a DSL modem to connect to the Internet, your ISP may use PPPoE to log you into the service. If you have an Internet connection in your home or small office that doesn’t require a modem, you may also use PPPoE. Your connection type is PPPoE if: 1) Your ISP gave you a user name and password, which is required to connect to the Internet. 2) Your ISP gave you software such as WinPOET or Enternet300 that you use to connect to the Internet. 3) You have to double-click on a desktop icon other than your browser to get on the Internet.
32N Wireless Router sectionstable of c ontents1 234 6789105 alT e RN aTe seTUP MeTHod (1)(2) (3) (4) (5) 1� User Name This space is provided to type in your user name that was assigned by your ISP. 2 � Password Type in your password and re-type it into the “Retype Password” box to confirm it. 3 � s ervice Name A service name is rarely required by an ISP. If you are not sure if your ISP requires a service name, leave this blank. 4 � MTU The MTU setting should never be changed unless your ISP gives you a specific MTU setting. Making changes to the MTU setting can cause problems with your Internet connection including disconnection from the Internet, slow Internet access, and problems with Internet applications working properly. 5 � d isconnect after X minutes… The “Disconnect” feature is used to automatically disconnect the Router from your ISP when there is no activity for a specified period of time. For instance, placing a check mark next to this option and entering “5” into the minute field will cause the Router to disconnect from the Internet after five minutes of no Internet activity. This option should be used if you pay for your Internet service by the minute.
33N Wireless Router sectionstable of c ontents1 234 6789105 alT e RN aTe seTUP MeTHod (1) (2) (4) (5) (3) (6) setting your Internet service Provider (I sP) Connection Type to Point-to-Point Tunneling Protocol (PPTP) [European Countries Only] Some ISPs require a connection using PPTP protocol, a type of connection most common in European countries. This sets up a direct connection to the ISP’s system. Type in the information provided by your ISP in the space provided. When you have finished, click “Apply Changes” (9). After you apply the changes, the Internet Status indicator will read “connection OK” if your Router is set up properly. 1 � PPTP account Provided by your ISP. Enter your PPTP account name here. 2 � PPTP Password Type in your password and retype it into the “Retype Password” box to confirm it. 3 � Host Name Provided by your ISP. Enter your host name here. 4 � g et IP by dHCP If your ISP provided you with a specific IP address, uncheck this box and enter your IP address, subnet mask, and default gateway in the fields that appear. 5 � s er vice IP address Provided by your ISP. Enter your service IP address here.
34N Wireless Router sectionstable of c ontents1 234 6789105 alT e RN aTe seTUP MeTHod setting your Connection Type if y ou are a Telstra® b igPond/ optusNet Cable User6� d isconnect after X… � The “Disconnect” feature is used to automatically disconnect the Router from your ISP when there is no activity for a specified period of time. For instance, placing a check mark next to this option and entering “5” into the minute field will cause the Router to disconnect from the Internet after five minutes of no Internet activity. This option should be used if you pay for your Internet service by the minute. [Australia Only] Follow the on-screen steps and click “Apply Changes” to complete your setup.
35N Wireless Router sectionstable of c ontents1 234 6789105 alT e RN aTe seTUP MeTHod Configuring your W aN Media a ccess Controller (Ma C) address All network components including cards, adapters, and routers, have a unique “serial number” called a MAC address. Your Internet Service Provider (ISP) may record the MAC address of your computer’s adapter and only let that particular computer connect to the Internet service. When you install the Router, its own MAC address will be “seen” by the ISP and may cause the connection not to work. Belkin has provided the ability to clone (copy) the MAC address of the computer into the Router. This MAC address, in turn, will be seen by the ISP’s system as the original MAC address and will allow the connection to work. If you are not sure whether your ISP needs to see the original MAC address, simply clone the MAC address of the computer that was originally connected to the modem. Cloning the address will not cause any problems with your network. Cloning your Ma C address To clone your MAC address, make sure that you are using the computer that was ORIGINALLY CONNECTED to your modem before the Router was installed. Click the “Clone” button (1). Click “Apply Changes” (3). Your MAC address is now cloned to the Router. s etting Custom domain Name server ( dN s) s ettings A “Domain Name Server” is a server located on the Internet that translates Universal Resource Locaters (URLs) like “www.belkin.com” to IP addresses. Many Internet Service Providers (ISPs) do not require you to enter this information into the Router. The “Automatic from ISP” box (1) should be checked if your ISP did not give you a specific DNS address. If you are using a static IP connection type, then you may need to enter a specific DNS address and secondary DNS address for your connection to work properly. If your connection type is dynamic or PPPoE, it is likely that you do not have to enter a DNS address. Leave the “Automatic from ISP” box checked. To enter the DNS address settings, uncheck the “Automatic from ISP” box and enter your DNS entries in the spaces provided. Click “Apply Changes” (2) to save the settings. (1) (2)
36N Wireless Router sectionstable of c ontents1 234 6789105 alT e RN aTe seTUP MeTHod entering a s pecific MaC address In certain circumstances you may need a specific WAN MAC address. You can manually enter one in the “MAC Address” page. Type in a MAC address in the spaces provided (2) and click “Apply Changes” (3) to save the changes. The Router’s WAN MAC address will now be changed to the MAC address you specified. (1) (3) (2)
37N Wireless Router sectionstable of c ontents1 2345 78910 UsINg TH e Web- based ad Va NC ed Use R INT eR fa Ce 6 Using your Internet browser, you can access the Router’s Web-Based Advanced User Interface. In your browser, type “192.168.2.1” (do not type in anything else such as “http://” or “www”) then press the “Enter” key. You will see the Router’s home page in your browser window. (1) (2) (3) Viewing the la N settings Clicking on the header of the L AN tab (1) will take you to the L AN tab’s header page. A quick description of the functions can be found here. To view the settings or make changes to any of the L AN settings, click on “L AN Settings” (2) or to view the list of connected computers, click on “DHCP client list” (3). Changing laN settings All settings for the internal L AN setup of the Router can be viewed and changed here. (1) (2) (4) (5) (6) (3)
38N Wireless Router sectionstable of c ontents1 2345 789106 UsINg TH e Web- based ad Va NC ed Use R INT eR fa Ce 1� IP address The “IP address” is the internal IP address of the Router. The default IP address is “192.168.2.1”. To access the advanced setup interface, type this IP address into the address bar of your browser. This address can be changed if needed. To change the IP address, type in the new IP address and click “Apply Changes”. The IP address you choose should be a non-routable IP. Examples of a non-routable IP are: 192.168.x.x (where x is anything between 1 and 254) 10.x.x.x (where x is anything between 1 and 254) 172.y.x.x (where x is anything between 1 and 254 and y is anything between 16 and 31) 2 � s ubnet Mask There is no need to change the subnet mask. This is a unique, advanced feature of your Belkin Router. It is possible to change the subnet mask if necessary; however, do NOT make changes to the subnet mask unless you have a specific reason to do so. The default setting is “255.255.255.0”. 3 � d HCP s erver The DHCP server function makes setting up a network very easy by assigning IP addresses to each computer on the network automatically. The default setting is “On”. The DHCP server can be turned OFF if necessary; however, in order to do so you must manually set a static IP address for each computer on your network. To turn off the DHCP server, select “Off” and click “Apply Changes”. 4 � IP Pool The range of IP addresses set aside for dynamic assignment to the computers on your network. The default is 2–100 (99 computers). If you want to change this number, you can do so by entering a new starting and ending IP address and clicking on “Apply Changes”. The DHCP server can assign 100 IP addresses automatically. This means that you cannot specify an IP address pool larger than 100 computers. For example, starting at 50 means you have to end at 150 or lower so as not to exceed the 100-client limit. The starting IP address must be lower in number than the ending IP address.