BEKO WMB 81241 LMB User Manual

							21EN
Programme and consumption table
EN2 Auxiliary functions
Programme (°C)
Max. Load (kg)
Water Consumption (l)
Energy Consumption (kWh)
Max. Speed***
Замачивание
Быстрая стирка
Дополнител\fное полоскание
Легкая глажка
Rinse Hold
Pet hair removal
Selectable 
temperature  range °C
\bлопок 908742.40 1600 •••••• 90-Cold
\bлопок 60872 1.70 1600 •••••• 90-Cold
\bлопок 40872 0.95 1600 •••••• 90-Cold
Детская 90872 2.10 1600 *• 90-30
\bлопок Эко 60**865 1.36 1600 •••••• 60-Cold
\bлопок Эко 40872 0.77 1600 •••••• 60-Cold
Интенсив 60872 1.60 1600 *• • 60-40
Синтетика 60345 1.00 1000 •••••• 60-Cold
Синтетика 40345 0.45 1000 •••••• 60-Cold
Экономичная 20º 203.5 390.16 1600 •20
Микс 40 403.5 450.55 1000 •••••• 40-Cold
Экспресс 14’ 30235 0.10 1400 •• 30-Cold
Ежедневная 90855 1.95 1400 •• 90-Cold
Ежедневная 60855 1.10 1400 •• 90-Cold
Ежедневная 30865 0.22 1400 •• 90-Cold
Шерст\f 401.5 450.30 1000 •• 40-Cold
Ручная 30135 0.20 1000 30-Cold
Темные вещи 40382 0.55 1000 *• 40-Cold
Самоочистка 70-95 2.15 800 * 70
Освежающая -2 30 0.03 1000 •-
  
						

							22EN
• : Selectable
* : Automatically selected, no canceling.
** : Energy Label programme (EN 60456)
 *** If maximum spin speed of the machine is lower then this value, you \
can only select 
up to the maximum spin speed.
- : See the programme description for maximum load.
C The auxiliary functions in the table may vary according to the model of your 
machine.
C Water and power consumption may vary subject to the changes in water pressure, 
water hardness and temperature, ambient temperature, type and amount of 
laundry, selection of auxiliary functions and spin speed, and changes in electr\
ic 
voltage.
C You can see the washing time of the programme you have selected on the display 
of the machine. It is normal that small differences may occur between the time 
shown on the display and the real washing time.
  
						

							23EN
Auxiliary function selection
Select the desired auxiliary functions 
before starting the programme. 
Furthermore, you may also select or 
cancel auxiliary functions that are suitable 
to the running programme by pressing 
the Start / Pause / Cancel button when 
the machine is operating. For this, the 
machine must be in a step before the 
auxiliary function you are going to select 
or cancel.
Depending on the programme, press a, 
b, c or d buttons to select the desired 
auxiliary function. Symbol of the selected 
auxiliary function appears on the display.
abc d
C Some functions cannot be selected 
together. If a second auxiliary function 
conflicting with the first one is 
selected before starting the machine, 
the function selected first will be 
canceled and the second auxiliary 
function selection will remain active. 
For example, if you want to select 
Quick Wash after you have selected 
the Prewash, Prewash will be 
canceled and Quick Wash will remain 
active.
C An auxiliary function that is not 
compatible with the programme 
cannot be selected. (See 
"Programme and consumption table")
C Auxiliary Function buttons may 
vary according to the model of the 
machine.
• Замачивание (Prewash)
A Prewash is only worthwhile for heavily 
soiled laundry. Not using the Prewash will 
save energy, water, detergent and time.
F1 appears on the display when you 
select this function (a).
• Быстрая стирка (Quick Wash)
This function can be used in Cottons and 
Synthetics programmes. It decreases the  washing times and also the number of 
rinsing steps for lightly soiled laundry.
F2 appears on the display when you 
select this function (b).
C 
When you select this function, 
load your machine with half of the 
maximum laundry specified in the 
programme table.
• Дополнительное полоскание 
(Rinse Plus)
This function enables the machine to 
make another rinsing in addition to the 
one already made after the main wash. 
Thus, the risk for sensitive skins (babies, 
allergic skins, etc.) to be effected by 
the minimal detergent remnants on the 
laundry can be reduced.
F3 appears on the display when you 
select this function (c).
• Легкая глажка (Anti-Creasing)
This function creases the clothes lesser 
when they are being washed. Drum 
movement is reduced and spinning 
speed is limited to prevent creasing. In 
addition, washing is done with a higher 
water level.
F4 appears on the display when you 
select this function (d).
• Rinse Hold
If you are not going to unload your 
clothes immediately after the programme 
completes, you may use rinse hold 
function to keep your laundry in the final 
rinsing water in order to prevent them 
from getting wrinkled when there is no 
water in the machine. Press Start / Pause 
/Cancel button after this process if you 
want to drain the water without spinning 
your laundry. Programme will resume and 
complete after draining the water.
If you want to spin the laundry held in 
water, adjust the Spin Speed and press 
Start / Pause / Cancel button.
The programme resumes. Water 
is drained, laundry is spun and the 
programme is completed.
• Soaking
The Soaking auxiliary function ensures 
better removal of stains ingrained into the 
clothes by holding them in the detergent 
water prior to startup of the programme.
• Pet hair removal
Downloaded From WashingMachine-Manual.com Manual•  
						

							24EN
This function helps to remove pet hair 
that remain on your garments more 
effectively.
When you select this function, Prewash 
and Extra Rinse steps are added to the 
normal programme. Thus, washing is 
performed with more water (30%) and the 
pet hair is removed more effectively.
A Never wash your pets in the washing 
machine.
Time display
Remaining time to complete the 
programme appears on the display 
while the programme is running. Tim is 
displayed as “01:30” in hours and minutes 
format.
C  Programme time may differ from 
the values in the "Programme and 
consumption table" depending on the 
water pressure, water hardness and 
temperature, ambient temperature, 
amount and the type of laundry, 
auxiliary functions selected and the 
changes at the mains voltage.
Delayed start
With the Delayed Start function the 
startup of the programme may be 
delayed up to 24 hours. Delayed start 
time can be increased by increments of 
30 minutes. 
C  Do not use liquid detergents when 
you set Delayed Start! There is the 
risk of staining of the clothes.
1.  Open the loading door, place the 
laundry and put detergent, etc.
2.  Select the washing programme, 
temperature, spin speed and, if 
required, the auxiliary functions.
3.  Set the desired delayed start time 
by pressing the Delayed Start + 
or - buttons. Delayed Start symbol 
flashes.
4.   Press Start / Pause / Cancel button. 
Delayed start countdown starts.  Delayed Start symbol illuminates 
steadily. Start symbol appears. “:” 
sign in the middle of the delayed 
start time on the display starts 
flashing.
C 
Additional laundry may be loaded 
during the delayed start period. At 
the end of the countdown, Delayed 
Start symbol disappears, washing 
cycle starts and the time of the 
selected programme appears on 
the display.
Changing the delayed start period
If you want to change the time during 
countdown:
1.  Press Start / Pause / Cancel button. 
“:” sign in the middle of the delayed 
start time on the display stops 
flashing. Pause symbol appears. 
Delayed Start symbol flashes. Start 
symbol disappears.
2.  Set the desired delayed start time 
by pressing the Delayed Start + or - 
buttons.
3.  Press Start / Pause / Cancel button. 
Delayed Start symbol illuminates 
steadily. Pause symbol disappears. 
Start symbol appears.
4.  “:” sign in the middle of the delayed 
start time on the display starts 
flashing.
Canceling the Delayed Start 
function
If you want to cancel the delayed start 
countdown and start the programme 
immediately:
1.  Press Start / Pause / Cancel button. 
“:” sign in the middle of the delayed 
start time on the display stops 
flashing.
2.  Start symbol disappears. Pause 
symbol and Delayed Start symbol 
flashes.
3.  Decrease the delayed start time by 
pressing the Delayed Start - button. 
Programme duration appears after 
30 minutes.
4.  Press Start / Pause / Cancel button 
to start the programme.
Starting the programme
1. Press Start / Pause / Cancel button 
to start the programme.
  
						

							25EN
2. Start symbol showing the startup of 
the programme will turn on.
3.  Loading door is locked and Door 
Locked symbol appears on the 
display.
4.  The symbol of the step from which 
the programme has started appears 
on the display (Prewash, Main Wash, 
Rinse, Softener and Spin).
Progress of programme
Progress of a running programme is 
indicated on the display with a set of 
symbols.
Relevant symbol appears on the display 
at the beginning of each programme step 
and all symbols remain lit at the end of 
the programme. The farthermost right 
symbol indicates the current programme 
step.
Prewash
If the Prewash auxiliary function is 
selected, Prewash symbol appears on 
the display indicating that the prewash 
step has started.
Main Wash
Main Wash symbol indicating that the 
main wash step has started appears on 
the display.
Rinse
Rinse symbol indicating that the rinsing 
step has started appears on the display.
Softener
Softener symbol indicating that the 
softener step has started appears on the 
display. 
Spin
Appears at the beginning of the final 
spin step and remains lit during Spin and 
Pump special programmes.
C If the machine does not pass to the 
spinning step, Rinse Hold function 
might be active or the automatic 
unbalanced load detection system 
might be activated due to the 
unbalanced distribution of the laundry 
in the machine.
Loading door lock
There is a locking system on the loading 
door of the machine that prevents 
opening of the door in cases when the 
water level is unsuitable. Door Locked symbol appears when the 
loading door is locked. This symbol will 
flash until the loading door becomes 
ready to open when programme 
completes or the machine is paused. Do 
not force to open the loading door in this 
step. Symbol disappears when the door 
is ready to open. You can open the door 
when the symbol disappears.
Changing the selections after 
programme has started
Switching the machine to pause 
mode
Press the Start / Pause / Cancel button 
to switch the machine to pause mode. 
Pause symbol appears on the display 
indicating that the machine is paused. 
Start symbol disappears.
F2F4F1F3
Changing the speed and temperature 
settings for auxiliary functions
Depending on the step the programme 
has reached, you may cancel or activate 
the auxiliary functions; see, "Auxiliary 
function selection". 
You may also change the speed and 
temperature settings; see, "Spin speed 
selection" and "Temperature selection".
Adding or taking out laundry
1. 
Press the Start / Pause / Cancel 
button to switch the machine to 
pause mode. The programme follow-
up light of the relevant step during 
which the machine was switched into 
the pause mode will flash.
2.  Wait until the Loading Door can be 
opened.
3.  Open the Loading Door and add or 
take out the laundry.
4.  Close the Loading Door.
5.   Make changes in auxiliary functions, 
temperature and speed settings if 
necessary.
6.   Press Start / Pause / Cancel button 
to start the machine.
  
						

							26EN
C The loading door will not open if the 
water temperature in the machine is 
high or the water level is above the 
door opening.
Child Lock
Use Child Lock function to prevent 
children from tampering with the 
machine. Thus you can avoid any 
changes in a running programme.
C You can switch on and off the 
machine with On / Off button when 
the Child Lock is active. When 
you switch on the machine again, 
programme will resume from where 
it has stopped.
To activate the Child Lock:
Press and hold 2
nd and 4th Auxiliary 
Function buttons for 3 seconds. “Con” 
appears on the display.
C  Same phrase will appear on the 
display if you press any button when 
Child Lock is enabled.
To deactivate the Child Lock:
Press and hold 2
nd and 4th Auxiliary 
Function buttons for 3 seconds. “COFF” 
appears on the display.
C  Do not forget to disable the child 
lock at the end of the programme 
if it was enabled before. Otherwise, 
machine will not allow to select a 
new programme.
Canceling the programme
Press and hold Start / Pause / Cancel 
button for 3 seconds. Start symbol 
flashes. Symbol of the step at which 
the programme was cancelled remains 
lit. "End" appears on the display and the 
programme is cancelled.
C If you want to open the loading 
door after you have cancelled the 
programme but it is not possible 
to open the loading door since the 
water level in the machine is above 
the loading door opening, then turn 
the Programme Selection knob 
to Pump+Spin programme and 
discharge the water in the machine.
Machine is in Rinse Hold mode
Spin symbol flashes and Pause symbol 
illuminates when the machine is in Rinse 
Hold mode.
If you want to spin your laundry when 
the machine is in this mode:
Adjust the spin speed and press Start / 
Pause / Cancel button. Pause symbol 
disappears and Start symbol appears. 
Programme resumes, discharges the 
water and spins the laundry.
If you only want to drain the water 
without spinning:
Just press Start / Pause / Cancel 
button. Pause symbol disappears. Start 
symbol appears. Programme resumes 
and discharges the water only.
End of programme
“End” appears on the display at the 
end of the programme. Symbols of the 
programme steps remain lit. Auxiliary 
function, spin speed and temperature 
that were selected at the beginning of 
the programme remain selected.
  
						

							27EN
6 Maintenance and cleaning
Service life of the product extends and 
frequently faced problems decrease if 
cleaned at regular intervals.
Cleaning the detergent drawer
Clean the detergent drawer at regular 
intervals (every 4-5 washing cycles) 
as shown below in order to prevent 
accumulation of powder detergent in 
time.
1.  Press the dotted point on the siphon 
in the softener compartment and pull 
towards you until the compartment is 
removed from the machine.
C If more than normal amount of water 
and softener mixture starts to gather 
in the softener compartment, the 
siphon must be cleaned.
2.  Wash the detergent drawer and the 
siphon with plenty of lukewarm water 
in a washbasin. Wear protective 
gloves or use an appropriate brush to 
avoid touching of the residues in the 
drawer with your skin when cleaning.
3.  Insert the drawer back into its place 
after cleaning and make sure that it is 
seated well.
Cleaning the loading 
door and the drum
Residues of softener, detergent and 
dirt may accumulate in your machine in 
time and may cause unpleasant odours 
and washing complaints. To avoid this, 
use the Drum Cleaning programme. If 
your machine is not featured with Drum 
Cleaning programme, use Cottons-90 
programme and select Additional Water 
or Extra Rinse auxiliary functions as well. 
Before starting the programme, put 
max. 100 g of powder anti-limescale into 
the main wash detergent compartment 
(compartment nr. II). If the anti-limescale  is in tablet form, put only one tablet into 
compartment nr. II. Dry the inside of the 
bellow with a clean piece of cloth after 
the programme has come to an end. 
C 
Repeat Drum Cleaning process in 
every 2 months.
C Use an anti-limescale suitable for 
the washing machines. 
After every washing make sure that no 
foreign substance is left in the drum.
If the holes on the bellow shown in the 
figure is blocked, open the holes using 
a toothpick.
C  Foreign metal substances in your 
machine will cause rust stains. 
Clean the stains on the drum 
surface by using cleaning agents for 
stainless steel. Never use steel wool 
or wire wool.
Cleaning the body 
and control panel
Wipe the body of the machine with 
soapy water or non-corrosive mild gel 
detergents as necessary, and dry with a 
soft cloth.
Use only a soft and damp cloth to clean 
the control panel.
A Never use sponge or scrub 
materials. These will damage the 
painted and plastic surfaces.
Cleaning the water 
intake filters
There is a filter at the end of each water 
intake valve at the rear of the machine 
and also at the end of each water 
intake hose where they are connected 
to the tap. These filters prevent foreign 
substances and dirt in the water to 
enter the washing machine. Filters 
should be cleaned as they do get dirty.
  
						

							28EN
1. Close the taps.
2.  Remove the nuts of the water intake 
hoses to access the filters on the 
water intake valves. Clean them with 
an appropriate brush. If the filters are 
too dirty, take them out by means of 
pliers and clean them.
3.  Take out the filters on the flat ends of 
the water intake hoses together with 
the gaskets and clean thoroughly 
under running water.
4.  Replace the gaskets and filters 
carefully in their places and tighten 
the hose nuts by hand.
Draining remaining water and 
cleaning the pump filter
The filter system in your machine prevents 
solid items such as buttons, coins and 
fabric fibers clogging the pump impeller 
during discharge of washing water. Thus, 
the water will be discharged without any 
problem and the service life of the pump 
will extend.
If the machine fails to drain water, the 
pump filter is clogged. Filter must be 
cleaned whenever it is clogged or in every 
3 months. Water must be drained off first 
to clean the pump filter.
In addition, prior to transporting the 
machine (eg., when moving to another 
house) and in case of freezing of the 
water, water may have to be drained 
completely.
A Foreign substances left in the pump 
filter may damage your machine or 
may cause noise problem.
In order to clean the dirty filter and 
discharge the water:
1.  Unplug the machine to cut off the 
supply power.
A Temperature of the water inside 
the machine may rise up to 90 ºC.  To avoid burning risk, filter must 
be cleaned after the water in the 
machine cools down.
2.  Open the filter cap.
  If the filter cap is composed of two 
pieces, press the tab on the filter cap 
downwards and pull the piece out 
towards yourself.
If the filter cap is one piece, pull the cap 
from both sides at the top to open.
C You can remove the filter cover by 
slightly pushing downwards with a 
thin plastic tipped tool, through the 
gap above the filter cover. Do not 
use metal tipped tools to remove the 
cover.
3.  Some of our products have 
emergency draining hose and some 
does not have. Follow the steps 
below to discharge the water.
Discharging the water when the product 
has an emergency draining hose:
a.  Pull the emergency draining hose out 
from its seat
b.  Place a large container at the end 
of the hose. Drain the water into 
the container by pulling out the plug 
  
						

							29EN
at the end of the hose. When the 
container is full, block the inlet of 
the hose by replacing the plug. After 
the container is emptied, repeat the 
above procedure to drain the water in 
the machine completely.
c.  When draining of water is finished, 
close the end by the plug again and 
fix the hose in its place.
d.  Turn the pump filter to take it out.
Discharging the water when the product 
does not have an emergency draining 
hose:
a.  Place a large container in front of the 
filter to catch water from the filter.
b.  Loosen pump filter (anticlockwise) 
until water starts to flow. Fill the 
flowing water into the container 
you have placed in front of the filter. 
Always keep a piece of cloth handy to 
absorb any spilled water.
c.  When the water inside the machine is 
finished, take out the filter completely 
by turning it.
4.  Clean any residues inside the filter as 
well as fibers, if any, around the pump 
impeller region.
5.  Install the filter.
A If your product has a water jet feature, 
be sure to fit the filter into its housing 
in the pump. Never force the filter 
while installing it into its housing. Seat 
the filter into its place completely. 
Otherwise, water may leak from the 
filter cap.
6.  If the filter cap is composed of 
two pieces, close the filter cap by 
pressing on the tab. If it is one piece, 
seat the tabs in the lower part into 
their places first, and then press the 
upper part to close.
   
						

							30EN
7 Troubleshooting
Programme cannot be started or selected. 
•  Washing machine has switched to self protection mode due to a supply problem 
(line voltage, water pressure, etc.). >>> Press and hold Start / Pause / Cancel 
button for 3 seconds to reset the machine to factory settings. (See "Canceling the 
programme")
Water in the machine.
•  Some water might have remained in the product due to the quality control 
processes in the production. >>> This is not a failure; water is not harmful to the 
machine.
There is water leaking from the bottom of the washing machine.
•  Likely problems with hoses or the pump filter. >>> Be sure the seals of the water 
inlet hoses are securely fitted. Attach the hose to the tap tightly.
•  Pump filter might not be closed fully. >>> Make sure that the pump filter is 
completely closed.
Machine does not fill with water.
•  Tap is turned off. >>> Open the inlet water taps fully.
•  Water inlet hose is bent. >>> Flatten the water inlet hose.
•  Water inlet filter is clogged. >>> Clean the water inlet filter.
•  The loading door is ajar. >>> Close the Loading Door.
Machine does not drain water.
•  Water drain hose might be clogged or twisted. >>> Clean or flatten the hose.
•  Pump filter is clogged. >>> Clean the pump filter.
Machine vibrates or makes noise.
•  Machine might be standing unbalanced. >>> Adjust the feet to level the machine.
•  A hard substance might have entered into the pump filter. >>> Clean the pump 
filter.
•  Transportation safety bolts are not removed. >>> Remove the transportation 
safety bolts.
•  Laundry quantity in the machine might be too little. >>> Add more laundry to the 
machine.
•  Machine might be overloaded with laundry. >>> Take out some of the laundry 
from the machine or distribute the load by hand to balance it homogenous\
ly in the 
machine.
•  Machine might be leaning on a rigid item. >>> Make sure that the machine is not 
leaning on anything.
Machine stopped shortly after the programme started.
•  Machine might have stopped temporarily due to low voltage. >>> It will resume 
running when the voltage restores to the normal level.
Machine directly discharges the water it takes in.
•  Draining hose might not be at adequate height. >>> Connect the water draining 
hose as described in the operation manual.
No water can be seen in the machine during washing.
C  The water level is not visible from outside of the washing machine. This is not a 
failure.