Beko Wm 5140 W Manual

EN21
auxiliary function, but you cannot 
select pre-wash.
C  The spin speed and temperature 
which are selected first will keep on 
being valid even if the position of the 
spin speed or temperature selection 
knob	is	changed.	Press	“Start/
Pause/Cancel”	button	and	switch	
the	machine	to	“Pause”	mode	in	
order to change the spin speed or 
temperature. New spin speed or 
temperature can be selected.  
Adding/removing laundry in standby 
mode
If you want to add more laundry into the 
machine after the...

EN22
Preparation
1. Turn the tap on completely. Check if 
the hoses are connected tightly.
2.	 Place	the	laundry	in	the	machine.
3. Add detergent and softener.
Starting
1.	 Press	the	“On/Off”	button.
2. Select the programme and the 
temperature.
3.	 If	required	(according	to	your	
machine’s	model):
–	 select	any	auxiliary	function,
–	 adjust	the	spin	speed,
–	 set	the	time	delay,
4. Close the loading door.
5.	 Press	“Start/Pause/Cancel”	button.
Canceling a program
•		Press	“Start/Pause/Cancel”	button...

EN23
Detergent drawer
Remove any powder residue buildup in 
the	drawer.	To	do	this;
1.	 Press	the	dotted	point	on	the	
siphon in the softener compartment 
and pull towards you until the 
compartment is removed from the 
machine.
C If more than a normal amount of 
water and softener mixture starts to 
gather in the softener compartment, 
the siphon must be cleaned.
2. Wash the dispenser drawer 
and the siphon with plenty of 
lukewarm water in a washbasin. 
Wear protective gloves or use an 
appropriate...

EN24
dirty.
•	 Close	the	taps.
•	 Remove	the	nuts	of	the	water	intake	
hoses to clean the surfaces of the 
filters on the water intake valves with 
an appropriate brush.
•	 If	the	filters	are	very	dirty,	you	can	
pull them out by means of pliers and 
clean them.
•	 Take	out	the	filters	on	the	flat	
ends of the water intake hoses 
together with the gaskets and clean 
thoroughly under streaming water.
•	 Replace	the	gaskets	and	filters	
carefully and tighten the hose nuts 
by hand.
Draining any remaining...

EN25
•		 Pull	out	the	pump	outlet	hose	from	
its housing.
•		 Place	a	large	container	at	the	end	of	
the hose. Drain the water off into the 
container by pulling out the plug at 
the end of the hose. If the amount 
of water to be drained off is greater 
than the volume of the container, 
replace the plug, pour the water out, 
then resume the draining process.
•		 After	draining	process	is	completed,	
replace the plug into the end of the 
hose and fit the hose back into its 
place.
If your product is not...

EN26
ProblemCauseExplanation / Suggestion
Program	cannot be started or selected. 
Machine	may	have	switched to self protection mode due to an infrastructure problem (such	as	line	voltage,	water	pressure,	etc.).
Reset	your	machine	by	pressing	“Start/Pause/Cancel”	button	for	3	seconds.	(see,	Cancelling	a	Program)
Water in the machine.
There may be some water in your machine when you receive it. This is from the quality control process and is normal.
It is not harmful to your machine.
There is water coming...

EN27
The water being taken in is directly discharged.
Improper position of the drain hose.Connect the water draining hose as described in the operation manual.
No water can be seen in the machine during washing.
This is not a problem. The water level is not visible from the outside of the machine.
The door is jammed.
Water level might be above the lower level of the door.Run	either	the	“Pump”	or	“Spin”	program.
Machine	might	be	heating	up the water or it may be at the spinning cycle.Wait until the...

EN28
It continuously washes.Remaining time does not count down.
In the case of a paused countdown while taking in water:Timer will not countdown until the machine is filled with the correct amount of water.
The machine will wait until there is a sufficient amount of water to avoid poor washing results due to lack of water. Then the timer will start to count down.
In the case of a paused countdown at the heating step:Time will not count down until the selected temperature for the program is reached
In the...

EN29
Washing performance is poor:Laundry turns gray
 - Using insufficient amount of detergent for a long time, - Washing at low temperatures for a long time, - Using insufficient amount of detergent for hard	waters	(soil	can	stick	to	the	laundry), - Using excessive amount of	detergent	(detergent	can	stick	to	the	laundry).
 - Use the recommended amount of detergent appropriate for water hardness and the laundry. - Select the proper temperature for the laundry to be washed. - If the water hardness is high,...

EN30
It does not rinse well.
The amount, brand and storage conditions of the detergent used might not be appropriate.
Store detergent in a closed and dry place. Do not keep them under high temperatures.
Detergent might have been put in the wrong compartment.
If detergent is put in the prewash compartment although prewash cycle is not selected, the machine can take this detergent during rinsing or softener step.
Machine	filter	may	be	clogged.Check the filter.
Drain hose may be folded.Check the drain...