Beko Wm 5100 User Manual

EN21
Preparation
1. Turn the tap on completely. Check if 
the hoses are connected tightly.
2.	 Place	the	laundry	in	the	machine.
3. Add detergent and softener.
Starting
1.	 Press	the	“On/Off”	button.
2. Select the programme and the 
temperature.
3.	 If	required	(according	to	your	
machine’s	model):
–	 select	any	auxiliary	function,
–	 adjust	the	spin	speed,
–	 set	the	time	delay,
4. Close the loading door.
5.	 Press	Start/Pause/Cancel	button.
Canceling a program
•	 Press	“Start/Pause/Cancel”	button	
for...

EN22
3. Set the spin speed if spin speed 
adjustment is available on your 
machine.
4.	 Press	“Start/Pause/Cancel”	button.	
After the program is finished
1.	 “Program	finished”	lamp	will	light	
up on the program follow-up 
indicator. The lid can be opened 
after	2	minutes	when	the	“Program	
Finished”	and	“Lid”	lamps	light	up	
continuously.  
2.	 Press	the	On/Off	button	to	shut	
down the machine.
3. Turn the water tap off.
4. Eliminate any folding of the rubber 
seal on the loading door and check 
for...

EN23
Detergent drawer
Remove any powder residue buildup in 
the	drawer.	To	do	this;
1.	 Press	the	dotted	point	on	the	
siphon in the softener compartment 
and pull towards you until the 
compartment is removed from the 
machine.
C If more than a normal amount of 
water and softener mixture starts to 
gather in the softener compartment, 
the siphon must be cleaned.
2. Wash the dispenser drawer 
and the siphon with plenty of 
lukewarm water in a washbasin. 
Wear protective gloves or use an 
appropriate...

EN24
•	 Remove	the	nuts	of	the	water	intake	
hoses to clean the surfaces of the 
filters on the water intake valves with 
an appropriate brush.
•	 If	the	filters	are	very	dirty,	you	can	
pull them out by means of pliers and 
clean them.
•	 Take	out	the	filters	on	the	flat	
ends of the water intake hoses 
together with the gaskets and clean 
thoroughly under streaming water.
•	 Replace	the	gaskets	and	filters	
carefully and tighten the hose nuts 
by hand.
Draining any remaining water 
and cleaning the...

EN25
place.
If your product is not supplied with an 
emergency drain hose, do the following 
as	shown	in	the	figure	below:
•		 Place	a	large	container	in	front	of	the	
filter to receive water flowing from 
the filter.
•		 Loosen	pump	filter	(anticlockwise)	
until water starts to flow out of it. 
Direct the flowing water into the 
container you have placed in front 
of	the	filter.	You	can	use	a	piece	of	
cloth to absorb any spilled water.
•		 When	there	is	no	water	left,	turn	the	
pump filter until it is...

EN26
ProblemCauseExplanation / Suggestion
Program	cannot be started or selected. 
Machine	may	have	switched to self protection mode due to an infrastructure problem (such	as	line	voltage,	water	pressure,	etc.).
Reset	your	machine	by	pressing	“Start/Pause/Cancel”	button	for	3	seconds.	(see,	Cancelling	a	Program)
Water in the machine.
There may be some water in your machine when you receive it. This is from the quality control process and is normal.
It is not harmful to your machine.
There is water coming...

EN27
No water can be seen in the machine during washing.
This is not a problem. The water level is not visible from the outside of the machine.
The door is jammed.
Water level might be above the lower level of the door.Run	either	the	“Pump”	or	“Spin”	program.
Machine	might	be	heating	up the water or it may be at the spinning cycle.Wait until the process is over.
Due to electrical safety mechanism, the door can only be opened a few minutes after the program has stopped.
Wait until the process is over....

EN28
It continuously washes.Remaining time does not count down.
In the case of a paused countdown while taking in water:Timer will not countdown until the machine is filled with the correct amount of water.
The machine will wait until there is a sufficient amount of water to avoid poor washing results due to lack of water. Then the timer will start to count down.
In the case of a paused countdown at the heating step:Time will not count down until the selected temperature for the program is reached
In the...

EN29
Washing performance is poor:Stain could not be removed, not cleaned.Laundry could not be whitened.
Insufficient amount of detergent used.Use recommended amount of detergent appropriate for the laundry.
Excessive laundry loaded into machineDo not load the machine in excess.
Wrong program and temperature might have been selected.
Select the proper program and temperature for the laundry to be washed.
Improper detergent may have been used.
Wrong type of detergent used.Put	the	detergent	in	the	correct...

EN30
Clothes stiffened.
Insufficient amount of detergent used.
If the water hardness is higher, using insufficient amount of detergent can cause the laundry to become stiff in time. Use appropriate amount of detergent according to the water hardness.
The detergent may have been placed into the wrong	compartment;	the	detergent may be mixed with the softener.
If detergent is put in the prewash compartment although prewash cycle is not selected, the machine can take this detergent during rinsing or softener...