BEKO WKD 65105 User Manual

							
WMD 65125
WMD 65105S
WMD 65105
WMD 65085
Washing Machine
Pralka automatyczna
Plně automatická pračka
Automatická pračka
 
						

							
2 - EN
1 Warnings
General Safety•  Never place your machine on a carpet covered floor. Otherwise, lack of airflow from below of your machine may cause electrical parts to overheat. This may cause problems with your washing machine.•  If the power cable or mains plug is damaged you must call Authorized Service for repair.•  Fit the drain hose into the discharge housing securely to prevent any water leakage and to allow machine to take in and discharge water as required. It is very important that the water intake and drain hoses are not folded, squeezed, or broken when the appliance is pushed into place after it is installed or cleaned.•   Your washing machine is designed to continue operating in the event of a power interruption. Your machine will not resume its program when the power restores. Press the “Start/Pause/Cancel” button for 3 seconds to cancel the program (See, Canceling a Program)•   There may be some water in your machine when you receive it. This is from the quality control process and is normal. It is not harmful to your machine.•  Some problems you may encounter may be caused by the infrastructure. Press "Start/Pause/Cancel" button for 3 seconds to cancel the program set in your machine before calling the authorized service.
First Use•   Carry out your first washing process without loading your machine and with detergent under “Cottons 90°C” program.•  Ensure that the cold and hot water connections are made correctly when installing your machine.•  If the current fuse or circuit breaker is less than 16 Amperes, please have a qualified electrician install a 16 Ampere fuse or circuit breaker.•  While using with or without a transformer, do not neglect to have the grounding installation laid by a qualified electrician. Our company shall not be liable for any damages that may arise when the machine is used on a line without grounding.•  Keep the packaging materials out of reach of children or dispose them by classifying according to waste directives.
Intended use•  This product has been designed for home use.•   The appliance may only be used for washing and rinsing of textiles that are marked accordingly.
Safety instructions•   This appliance must be connected to an earthed outlet protected by a fuse of suitable capacity.•   The supply and draining hoses must always be securely fastened and remain in an undamaged state.•  Fit the draining hose to a washbasin or bathtub securely before starting up your machine. There may be a risk of being scalded due to high washing temperatures!•  Never open the loading door or remove the filter while there is still water in the drum.•   Unplug the machine when it is not in use.•  Never wash down the appliance with a water hose! There is the risk of electric shock!•   Never touch the plug with wet hands. Do not operate the machine if the power cord or plug is damaged.•   For malfunctions that cannot be solved by information in the operating manual:•  Turn off the machine, unplug it, turn off the water tap and contact an authorized service agent. You may refer to your local agent or solid waste collection center in your municipality to learn how to dispose of your machine.  
If there are children in your 
house...•   Keep children away from the machine when it is operating. Do not let them tamper with the machine.•   Close the loading door when you leave the area where the machine is located.
 
						

							
3 - EN
2 Installation
Removing packaging 
reinforcementTilt the machine to remove the packaging reinforcement. Remove the packaging reinforcement by pulling the ribbon.
Opening the transportation locksA  Transportation safety bolts must be removed before operating the washing machine! Otherwise, the machine will be damaged!1.  Loosen all the bolts with a spanner until they rotate freely (“C”)2.  Remove transportation safety bolts by turning them gently.3.  Fit the covers (supplied in the bag with the Operation Manual) into the holes on the rear panel. (“P”)
C Keep the transportation safety bolts in a safe place to reuse when the washing machine needs to be moved again in the future.C Never move the appliance without the transportation safety bolts properly fixed in place!
Adjusting the feetA  Do not use any tools to loosen the lock nuts. Otherwise, they can be damaged.1.  Manually (by hand) loosen the lock nuts on the feet.
2.  Adjust them until the machine stands level and firmly.3.  Important: Tighten all lock nuts up again.
Connecting to the water supply.Important:
•   The water supply pressure required to run the machine must be 1-10 bar (0,1 – 1 MPa). (Practically, it is necessary to have 10 – 80 liters of water flowing from the tap in one minute to have your machine run 
smoothly.)
•   Connect the special hoses supplied with the machine to the water intake valves on the machine. •  In order to prevent water leakage that may occur at the connection points, there are rubber seals (4 seals for the models with double water inlet and 2 seals for other models) attached to the hoses. These seals should be used at the tap and machine connection ends of the hoses. The plain end of the hose fitted with a filter must be attached to the tap and the elbowed end must be attached to the machine. Tighten the nuts of the hose well by hand; never use wrenches to tighten the nuts.•  Models with a single water inlet should not be connected to the hot water tap.When returning the appliance to its place after maintenance or cleaning, care should be taken not to fold, squeeze or block the hoses.
Connecting to the drainThe water discharge hose can be attached to the edge of a washbasin or bathtub. The drain hose should be firmly fitted into the drain as to not get out of its housing.
Important:
•   The end of the drain hose must be directly connected to the wastewater drain or to the washbasin.•   The hose should be attached to a height of at least 40 cm, and 100 cm at most.•   In case the hose is elevated after laying it on the floor level or close to the ground (less than 40 cm above the ground), water discharge becomes more difficult and the laundry may come out wet.
 
						

							
4 - EN
•   The hose should be pushed into the drainage for more than 15 cm. If it is too long you may have it shortened.•  The maximum length of the combined hoses must not be longer than 3.2 m.
Electrical connectionConnect the machine to an earthed outlet protected by a fuse of suitable capacity.
Important:•   Connection should comply with national regulations.•   The voltage and the allowed fuse protection are specified in the section “Technical Specifications”.•   The specified voltage must be equal to your mains voltage.•   Connection via extension cords or multi-plugs should not be made.B  A damaged power cable must be replaced by a qualified electrician.B  The appliance must not be operated unless it is repaired! There is the risk of electric shock!
3 Initial preparations for 
washing
Preparing clothes for washingLaundry items with metal attachments such as, bras, belt buckles and metal buttons will damage the machine. Remove metal attachments or place the items in a clothing bag, pillow case, or something similar.
•  Sort the laundry according to type of fabric, color, and degree of soiling and permissible water temperature. Always follow the advice on the garment labels.•   Place small items like infants’ socks and nylon stockings, etc. in a laundry bag, pillow case or something similar. This will also save your laundry from getting lost.•   Wash “machine washable” or “hand washable” labeled products only with an appropriate program.•   Do not wash colors and whites together. New, dark colored cottons may release a lot of dye. Wash them separately.•   Use only dyes/color changers and lime removers suitable for machine wash. Always follow the instructions on the packaging.•   Wash trousers and delicate clothes turned inside out.
Correct load capacityC Please follow the information in the “Program Selection Table”. Washing 
results will degrade when the machine is overloaded.
Loading doorThe door locks during program operation and the Door Locked Symbol (Figure 3-13i) lights up. The door can be opened when the symbol fades out.
Detergents and softenersDetergent DrawerThe detergent drawer is composed of three compartments:
The detergent dispenser may be in two different types according to the model of your machine.
– (I) for prewash
– (II) for main wash
- (III) siphon 
– () for softener
Detergent, softener and other cleaning agentsAdd detergent and softener before starting the washing program.
Never open the detergent dispenser drawer while the washing program is running!
When using a program without pre-wash, no detergent should be put into the pre-wash compartment (Compartment no. I).
Detergent quantityThe amount of washing detergent to be used depends on the amount of laundry, the degree of soiling and water hardness.
•   Do not use amounts exceeding the quantities recommended on the package to avoid problems of excessive foam, poor rinsing, financial savings and finally, environmental protection.•   Never exceed the (> max 
						

							
5 - EN
Turning the machine onPlug in your machine. Turn the tap on completely. Check if the hoses are connected tightly. Place the laundry in the machine. Add detergent and softener. Press the “On/Off” button.
Program selectionSelect the appropriate program from the program table and the following washing temperature table according to type, amount and degree of soiling of the laundry. Select the desired program with the program selection button.
C Programs are limited with the highest spin speed appropriate for that particular type of cloth.
Main programs Depending on the type of textile, the following main programs are available:
•CottonsYou can wash your durable clothes with this program. Your laundry will be washed with vigorous washing movements during a longer washing cycle. 
•Synthetics/MixYou can wash your less durable clothes on this program. Lighter washing movements and shorter washing cycle is used compared to “Cottons” program. It is recommended for your synthetic clothes (such as shirts, blouses, synthetic/cotton blended garments, etc.). For curtains and lace, the “Synthetic(mix)40” program with pre-wash and anti-creasing functions selected is recommended.
•WoolensYou can wash your machine-washable woolen garments on this program. Wash by selecting the proper temperature according to the labels of your clothes. It is recommended to use appropriate detergents for woolens. 
Additional programs For special cases, there are also extra programs available:
• DelicatesYou can wash your delicate clothes on this program. It has more sensitive washing movements and does not make intermediate spinning compared to “Synthetic” program.
4  Selecting a Program and Operating Your Machine
1  -  Spin Speed Adjustment Button
2  -  Time Delaying Button
3  -  Auxiliary Function Keys
4  -  Start/Pause/Cancel Button
5  -  Program Selection Knob
6  -  Display
7  -  Child-proof Lock Indicator*
8  -  Program Follow-up Indicators 
9  -  On/Off Button
* According to your machine’s model
8
60°
4040
40°
Mix
30°
30°
40°Reset3’’
40°
40°
30° 30°
60°60°
90°
mini
30
super
40
5
13
987
42
6
Control panel
 
						

							
6 - EN
• ShirtYou can use this program to wash cottons and synthetics together. There is no need to sort them.
• SportThis program is suitable for clothes that are normally worn for a short time such as sportswear. It is used to quickly wash a small amount of cotton/synthetic blended clothes.
• SuperThis program washes for a longer period at 40°C and gives the same result as the “Cottons 60°C” program, thus it saves energy. It is suitable for clothes for which you cannot use the “Cottons 60°C” program. 
• MiniThis program is used to quickly wash (30 minutes) a small amount of lightly soiled cotton garments.
• BabyIncreased hygiene is provided by a longer heating period and an additional rinse cycle. It is recommended for baby clothes and clothes worn by allergic people.
• Hand WashYou can wash your woolen/delicate clothes that bear “not machine- washable” labels for which hand wash is recommended on this program. It washes the laundry with very tender washing movements without damaging your clothes.
C Sort the laundry according to type of fabric, color, degree of soiling and permissible water temperature when choosing a program.
Special programsFor specific applications, you can select any of the following programs:
• RinseThis program is used when you want to rinse or starch separately.
• Spin and PumpThis program is used to apply an additional spin cycle for the laundry or to drain the water in the machine.
Before starting this program, select the desired spin sped and press “Start/Pause/Cancel” button. Your machine drains the water after spinning at the set spin speed.
If you only want to drain the water without spinning your laundry, select “Spin and Pump” program, and then select no spin function with spin speed selection button. Press “Start/Pause/Cancel” button.
A You should use a lower spin speed for delicate laundries.
Spin Speed selectionWhenever a new program is selected, the maximum spin speed of the selected program is displayed on the spin speed indicator.
To decrease the spin speed, press the “Spin” button. Spin speed decreases gradually. Then, rinse hold and no spin options are shown respectively.
Rinse hold is shown with “” and no spin is shown with “” symbols.
If you do not want to unload your clothes immediately after the program, you may use rinse hold function in order to prevent your clothes become wrinkled in anhydrous conditions. With this function, your laundry is kept in the final rinsing water. If you want to spin your laundry that you left in water:
- Adjust the spin speed.
- Press “Start/Pause/Cancel” button.
Program resumes. Your machine drains the water and spins your laundry.
You can use no spin function in order to drain the water without spinning at the end of the program.
 
						

							
7 - EN
Program and consumption table
• : Selectable
* : Automatically selected, not cancellable.
**: Energy Label programme (EN 60456)
Water and power consumption and programme duration may differ from the table shown, subject to changes in water pressure, water hardness and temperature, ambient temperature, type and amount of laundry, selection of auxiliary functions, and fluctuations in the supply voltage.
“Super 40” programme may be selected instead of “Cotton 60*” programme during winter in areas where the input water temperature is low and/or in areas with low supply voltage.
C The auxiliary functions in the table may differ according to the model of your machine.
 Programme
Max. Load (kg)Programme Duration (~min)Water Consumption (l)Energy Consumption (kWh)PrewashQuick WashRinse PlusAnti-CreasingRinse HoldNo Heat
 Cottons905132451.50••••••
 Cottons60**5135450.95••••••
 Cottons405132450.63••••••
 Super405160450.69••
 Intensive605163560.96*•••
 Sports402.575370.38••••••
 Synthetics602.5103450.77••••••
 Synthetics(mix)402.596450.46••••••
 Shirts402.591400.30•••••
 Delicate30265370.24••••
 Woollens401.560450.21•••
 Hand wash30139330.14•
Baby
 
						

							
8 - EN
Auxiliary functionsAuxiliary Function Selection ButtonsSelect the required auxiliary functions before starting the program.
C Some combinations cannot be selected together. (Ex.: Pre-wash and Quick Wash.Warning signal on the selected auxiliary function will light up.
Auxiliary function selectionIf an auxiliary function that should not be selected together with a previously selected function is chosen, the first selected function will be cancelled and the last auxiliary function selection will remain active.
(Ex.: If you want to select pre-wash first and then quick wash, pre-wash will be cancelled and quick wash will remain active.
Auxiliary function that is not compatible with the program cannot be selected. (see, “Program Selection Table”)
C Auxiliary function buttons may differ according to the model of your machine.
Pre-washA pre-wash is only worthwhile for heavily soiled laundry. Without pre-wash you save energy, water, detergent and time.
C Pre-wash without detergent is recommended for lace and curtains.Quick washThis function can be used for “Cottons” and “Synthetics” programs. It decreases the washing times for lightly soiled laundries and also the number of rinsing steps.
Rinse PlusWith this function, you can increase the number of current rinsing steps. Thus, sensitive skins’ risk of being affected by the remainder detergent on the clothes will be decreased.
Anti-creasingWith this function, drum movement will be lessened to prevent creasing and spinning speed is limited. In addition, washing is carried out at a higher water level.
C Whenever you select this auxiliary function, load your machine with half of the maximum laundry specified in the program table.No HeatIf you wish to wash your clothes in cold water, you can use this program.
Time displayThe display shows the time remaining for the program to complete while a program is running. Program duration may differ from the 
values in the consumption table subject to the changes in the water pressure, water hardness and temperature, ambient temperature, type and amount of laundry, auxiliary functions selected, and changes in the supply voltage.
Time delayWith the “Time delay” function you can delay the program start up to 24 hours. Time delay can be set with steps of one hour for the first three hours and with steps of three hours for the remainder (1, 2, 3, 6, 9, …24).
1. Pres “Time Delay” button to adjust the desired time.
2. Press “Start/Pause/Cancel” button. The time delay will start to count down. 
C More laundry may be loaded during the time delay period.
Changing the delay timeIf you want to change the time during the countdown:
1. Press “Start/Pause/Cancel” button.
2. Pres “Time Delay” button to adjust the desired time delay.
3. Press “Start/Pause/Cancel” button.
Canceling the time delayIf you want to cancel the time delay countdown and start the program:
1. Press “Start/Pause/Cancel” button.
2. Pres “Time Delay” button to decrease the time delay.
3. Press “Start/Pause/Cancel” button to start the program.
Starting the Program1. Press “Start/Pause/Cancel” button to start the program.
2. Program follow-up lamp showing the startup of the program will light up.
Progress of programProgress of a running program is shown through the program follow-up indicator. At the beginning of every program step, the relevant indicator lamp will light up and light of the completed step will turn off. The symbol that is lit up at the far right of the series of symbols indicates the step that is being carried out.
C If the machine is not spinning, the program may be in rinse hold mode or the automatic spin correction system has been activated due to an excessive unbalanced distribution of laundry in the machine.
 
						

							
9 - EN
Changing the selections after the 
program has startedTurning the program knob while the program is in a normal flow will not change the program.
Switching the machine to standby modePress “Start/Pause/Cancel” button momentarily to switch your machine to the standby mode. Auxiliary functions can be cancelled or selected in accordance with the step the program is at. The door can be opened if the water level is suitable. Laundry may be added / taken out by opening the door.
Door lockThe loading door can not be opened yet due to safety reasons while the “Ready” lamp is flashing. The loading door can be opened once the “Ready” lamp starts lighting up continuously.
Child-proof lockYou can protect the appliance from being tampered by children by means of the child-proof lock. In this case, no change can be made in the running program.
The machine is switched to child-lock by pressing the 1st and 2nd auxiliary functions for 3 sec. “C on” (Child lock is activated) label appears on the screen. The same symbol will also be displayed whenever any button is pressed while the machine is child-locked.
Child-proof lock lamp on the program follow-up indicator will light up when the child-proof lock is activated.
To deactivate the child-proof lock, press the 1st and 2nd auxiliary function buttons for 3 sec. “C OFF” (Child-proof lock is deactivated) symbol appears on the screen. Child-proof lock lamp on the program follow-up indicator will go off when the child-proof lock is deactivated.
Ending the program through 
canceling“Start/Pause/Cancel” button is pressed for 3 seconds to cancel the program. “Ready” warning lamp flashes during canceling and “End” will appear on the display.
5 Maintenance and cleaning
Detergent DrawerRemove any powder residue buildup in the drawer. To do this;
1.  Press the dotted point on the siphon in the softener compartment and pull towards you until the compartment is removed from the machine.
C If more than a normal amount of water and softener mixture starts to gather in the softener compartment, the siphon must be cleaned.2.  Wash the dispenser drawer and the siphon with plenty of lukewarm water in a washbasin. 3.  Replace the drawer into its housing after cleaning.  Check if the siphon is in its original location.
Inlet water filtersThere is a filter at the end of each water intake valve at the back side of the machine and also at the end of each water intake hose where they are connected to the tap. These filters prevent the foreign substances and dirt in the water to enter into the machine. Filters should be cleaned as they get dirty.
•  Close the taps.•  Remove the nuts of the water intake hoses to clean the surfaces of the filters on the water intake valves with an appropriate brush.•  If the filters are very dirty, you can pull them out by means of pliers and clean them.•  Take out the filters on the flat ends of the water intake hoses together with the gaskets and clean thoroughly under streaming water.•  Replace the gaskets and filters carefully to their places and tighten the hose nuts by hand.
 
						

							
10 - EN
•  Pull out the pump outlet hose from its housing.•   Place a large container at the end of the hose. Drain the water off into the container by pulling out the plug at the end of the hose. If the amount of water to be drained off is greater than the volume of the container, replace the plug, pour the water out, then resume the draining process.•   After draining process is completed, replace the plug into the end of the hose and fit the hose back into its place.
If your product is not supplied with an emergency drain hose, do the following as shown in the figure below:
•   Place a large container in front of the filter to receive water flowing from the filter.•   Loosen pump filter (anticlockwise) until water starts to flow out of it. Direct the flowing water into the container you have placed in front of the filter. You can use a piece of cloth to absorb any spilled water.•   When there is no water left, turn the pump filter until it is completely loose and remove it.•   Clean any residues inside the filter as well as fibers, if any, around the propeller region.•   If your product has a water jet feature, be sure to fit the filter into its housing in the pump. Never force the filter while replacing it into its housing. Fit the filter fully into its housing; otherwise, water may leak from the filter cap.
4- Close the filter cap.
Close the two-piece filter cap of your product by pushing the tab on it.
Close the one-piece filter cap of your product by fitting the tabs on the bottom into their positions and pushing the upper part of it.
Draining any remaining water and 
cleaning the pump filterYour product is equipped with a filter system which ensures a cleaner water discharge that extends pump life by preventing solid items such as buttons, coins and fabric fibers from clogging the pump propeller during discharge of the washing water.
•   If your machine fails to drain the water, the pump filter may be clogged. You may have to clean it every 2 years or whenever it is plugged. Water must be drained off to clean the pump filter. In addition, water may have to be drained off completely in the following cases:
•   before transporting the machine (e.g. when moving house)•   when there is the danger of frostIn order to clean the dirty filter and discharge the water;
1- Unplug the machine to cut off the supply power.
A There may be water at 90°C in the machine. Therefore, the filter must be cleaned only after the inside water is cooled down to avoid hazard of scalding.
2- Open the filter cap. The filter cap may be composed of one or two pieces according to the model of your machine.
If it is composed of two pieces, press the tab on the filter cap downwards and pull the piece out towards yourself.
If it is composed of one piece, hold it from both sides and open it by pulling out.
3- An emergency drain hose is supplied with some of our models. Others are not supplied with this item.
If your product is supplied with an emergency drain hose, do the following as shown in the figure below: