BEKO WKD 23560 R User Manual

17    EN
Program selection and consumption table
•	:	Selectable
*	:	Automatically	selected,	not	cancellable.
**:	Energy	Label	programme	(EN	60456)
Water and power consumption and program duration may differ from the tab\
le 
subject to changes in water pressure, water hardness and temperature, am\
bient 
temperature, type and amount of laundry, selection of auxiliary function\
s, and 
changes in electric voltage.
C The auxiliary functions in the table may differ according to the model o\
f your...

18    EN
Auxiliary functionsAuxiliary function selection keys
Select the required auxiliary functions 
before starting the program.
C Auxiliary function buttons may differ 
according to the model of your 
machine.
Auxiliary function selection
If an auxiliary function that should not 
be selected together with a previously 
selected function is chosen, the first 
selected function will be cancelled and 
the last auxiliary function selection will 
remain active.
For	example:	If	you	want	to	select	pre-
wash...

19    EN
program is started by pressing the 
“Start/Pause/Cancel”	button	after	
making the time delay selection. 
C	More	laundry	may	be	loaded/ removed during the time delay 
period.
Changing and canceling the time 
delay.
1.	 Press	the	“Start/Pause/Cancel”	 button to switch the machine to 
“Pause”	mode.	
2.	 Press	“Start/Pause/Cancel”	button	 to start the program after making the 
new time delay selection. 
C  In the event that any of the lights 
of 3-6-9 options does not light up 
after selecting the...

20    EN
“Start/Pause/Cancel”	button	and	
switch	the	machine	to	“Pause”	mode	
in order to change the spin speed 
or temperature. New spin speed or 
temperature can be selected.  
Adding/removing laundry in standby 
mode
If you want to add more laundry into the 
machine after the washing cycle has 
started,	put	the	machine	into	“Pause”	
mode	by	pressing	the	“Start/Pause/
Cancel”	button.	The	“Ready”	lamp	on	
the program follow-up indicator will light 
up after 1-2 minutes if the water level in 
the machine...

21    EN
Preparation
1. Turn the tap on completely. Check if 
the hoses are connected tightly.
2.	 Place	the	laundry	in	the	machine.
3.  Add detergent and softener.
Starting
1.	 Press	the	“On/Off”	button.
2.  Select the programme and the 
temperature.
3.	 If	required	(according	to	your	 machine’s	model):
–	 select	any	auxiliary	function,
–	 adjust	the	spin	speed,
–	 set	the	time	delay,
4.  Close the loading door.
5.	 Press	“Start/Pause/Cancel”	button.
Canceling a program
•	 	Press	“Start/Pause/Cancel”...

22    EN
program	follow-up	indicator.	Open	
the loading door and take out the 
clothes.
2.	 Press	the	“On/Off”	button.
3.  Turn the water tap off.
4.  Eliminate any folding of the rubber 
seal on the loading door and check 
for impurities.
5.  Leave the loading door and detergent 
drawer open to dry.
 

23    EN
Detergent drawerRemove any powder residue buildup in 
the	drawer.	To	do	this;
1.	 Press	the	dotted	point	on	the	siphon	in the softener compartment and pull 
towards you until the compartment is 
removed from the machine.
C  If more than a normal amount of 
water and softener mixture starts to 
gather in the softener compartment, 
the siphon must be cleaned.
2.  Wash the dispenser drawer and the 
siphon with plenty of lukewarm water 
in a washbasin. Wear protective 
gloves or use an appropriate...

24    EN
under streaming water.
•	 Replace	the	gaskets	and	filters	 carefully and tighten the hose nuts by 
hand.
Draining any remaining water 
and cleaning the pump filter
Filter system in your machine prevents 
solid items such as buttons, coins and 
fabric fibers clogging the pump propeller 
during discharging of the washing 
water. Thus, a good water discharger is 
achieved and the pump life is extended.
•		 If	your	machine	fails	to	drain	the	water, the pump filter may be 
clogged.	You	may	have	to...

25    EN
filter to receive water flowing from the 
filter.
•		 Loosen	pump	filter	(anticlockwise)	 until water starts to flow out of it. 
Direct the flowing water into the 
container you have placed in front of 
the	filter.	You	can	use	a	piece	of	cloth	
to absorb any spilled water.
•		 When	there	is	no	water	left,	turn	the	 pump filter until it is completely loose 
and remove it.
•		 Clean	any	residues	inside	the	filter	 as well as fibers, if any, around the 
propeller region.
•		 If	your	product	has	a...

26    EN
ProblemCause Explanation	/	Suggestion
Program	
cannot be 
started or 
selected. Machine	may	have	
switched to self 
protection mode due to 
an infrastructure problem 
(such	as	line	voltage,	water	
pressure,	etc.).
Reset	your	machine	by	pressing	“Start/Pause/
Cancel”	button	for	3	seconds.	(see,	Cancelling	a	
Program)
Water in the 
machine. There may be some water 
in your machine when you 
receive it. This is from the 
quality control process and 
is normal.
It is not harmful to your machine....