BEKO WKD 23560 R User Manual
Have a look at the manual BEKO WKD 23560 R User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 187 Beko manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
17 EN Program selection and consumption table • : Selectable * : Automatically selected, not cancellable. **: Energy Label programme (EN 60456) Water and power consumption and program duration may differ from the tab\ le subject to changes in water pressure, water hardness and temperature, am\ bient temperature, type and amount of laundry, selection of auxiliary function\ s, and changes in electric voltage. C The auxiliary functions in the table may differ according to the model o\ f your machine. Programme Max. Load (kg) Programme Duration (~min) Water Consumption (l) Energy Consumption (kWh) Prewash Quick Wash Rinse Plus Anti-Creasing Rinse Hold Spin speed reduction No Spin Cottons 903.5 150 451.45••••••• Cottons 60**3.5135 430.66••••••• Cottons 403.5 125 400.45••••••• Intensive 603.5 160 500.80• ••• Babycare 653.5 170 550.95* ••• Synthetics 60211 5 350.70••••••• Synthetics 402105 350.40••••••• Mix 402.5 95350.40••••••• Delicate 401.5 70350.30••••• Woollens 40155 300.20• ••• Hand wash 30140 250.10•• Mini 301.5 30300.10•• Downloaded From WashingMachine-Manual.com Manual•
18 EN Auxiliary functionsAuxiliary function selection keys Select the required auxiliary functions before starting the program. C Auxiliary function buttons may differ according to the model of your machine. Auxiliary function selection If an auxiliary function that should not be selected together with a previously selected function is chosen, the first selected function will be cancelled and the last auxiliary function selection will remain active. For example: If you want to select pre- wash first and then quick wash, pre- wash will be cancelled and quick wash will remain active. Auxiliary function that is not compatible with the program cannot be selected. (see “Program Selection Table”) Pre-wash A pre-wash is only worthwhile for heavily soiled laundry. Without pre-wash you save energy, water, detergent and time. C Pre-wash without detergent is recommended for lace and curtains. Less detergent should be put in the main wash compartment as loose knit fabrics (lace) foam too much due to its meshed structure. Quick wash This function can be used for cottons and synthetics programs. It decreases the washing times for lightly soiled laundries and also the number of rinsing steps. Shortens the program time approximately 45 minutes. Extra rinse With this function, you can increase the number of current rinsing steps. Thus, sensitive skins’ risk of being affected by the remainder detergent on the clothes will be decreased. Rinse hold If you do not want to unload your clothes immediately after the cotton, synthetics, woolen and delicate fabrics program, you may release your clothes inside the machine in the last rinsing water by pressing the rinse hold button in order to prevent your clothes become wrinkled. You can spin by pressing “Start/Pause/Cancel” button after this process. Anti-creasing This function reduces drum movement and limits the spinning speed to prevent creasing. In addition, washing is carried out at a higher water level. C Use this function for delicate laundries that crease easily. C Whenever you select this auxiliary function, load your machine with half of the maximum laundry specified in the program table. Reducing Speed You may use the speed reduction button whenever you wish to spin your clothes below the maximum spin speed. When speed reduction button is pressed, spin speed will be at the minimum rpm given on the panel. No spin You may use this program if you do not want to spin your clothes at the end of cottons, synthetics, woolen or delicate programs. Time delayApplies for models with time delay functionIf you wish to wash your clothes at a later time, with the time delay function you can delay the program start up 3 hours, 6 hours or 9 hours. 1. Open the loading door, place the laundry inside and fill detergent drawer. 2. Set the washing program, temperature, spin speed and, if required, the auxiliary functions. 3. When the time delaying button is pressed once, a 3 hour delay is selected and the relevant led lights. When the same button is pressed again, 6 hours; and if pressed once more, 9 hours delay will be selected. If the time delaying button is pressed one more time, time delaying function will be cancelled. Set the time delay as you require. 4. Delayed operation of the selected
19 EN program is started by pressing the “Start/Pause/Cancel” button after making the time delay selection. C More laundry may be loaded/ removed during the time delay period. Changing and canceling the time delay. 1. Press the “Start/Pause/Cancel” button to switch the machine to “Pause” mode. 2. Press “Start/Pause/Cancel” button to start the program after making the new time delay selection. C In the event that any of the lights of 3-6-9 options does not light up after selecting the new time delay, it means that time delay function is cancelled. Starting the Program1. Press “Start/Pause/Cancel” button to start the program. 2. “Start/Pause/Cancel” button will light up to indicate that the program has started. 3. The door is locked and the “Ready” light fades. Progressing a programProgress of a running program is shown through the program follow-up indicator. At the beginning of every program step, the relevant indicator lamp will illuminate and the light of the completed step will turn off. The symbol that is lit up at the far right of the series of symbols indicates the step that is being carried out. The “Wash” light on the program follow- up indicator illuminates when “Start/ Pause/Cancel” button is pressed after selecting the washing program. “Spin” lamp will light up at the final spin step. The “Ready” lamp will light up again when the program is over and the door is unlocked. You can put your machine into “Pause” mode by pressing the “Start/Pause/ Cancel” button when it is operating. In this case, “Start/Pause/Cancel” light will flash. C If the machine is not spinning, the program may be in rinse hold mode or the automatic spin correction system has been activated because of unbalanced distribution of laundry in the machine. Changing the program after the program has started You can use this feature after your machine has started to wash different textile groups in the same batch of clothes under higher or lower temperatures. For example; Press and hold the “Start/Pause/ Cancel” button for 3 seconds to “Cancel” the program in order to select “Cottons 40” program instead of “Cottons 60” program. Select the “Cottons 40” program by rotating the program knob. Press “Start/Pause/Cancel” button to start the program. C The program which is selected first will go on even if the program selection button is moved and another program mode is selected while the machine is operating. You must cancel the ongoing program in order to change the washing program. (See, Canceling a Program) Selecting or cancelling an auxiliary function/temperature/spin speed 1. Press the “Start/Pause/Cancel” button to switch the machine to “Pause” mode. 2. Change the auxiliary function’s temperature and spin speed. 3. Press “Start/Pause/Cancel” button to start the program. C The selection to be made must be appropriate. For example, if your machine is on the main wash cycle, you may select additional rinse auxiliary function, but you cannot select pre-wash. C The spin speed and temperature which are selected first will keep on being valid even if the position of the spin speed or temperature selection knob is changed. Press
20 EN “Start/Pause/Cancel” button and switch the machine to “Pause” mode in order to change the spin speed or temperature. New spin speed or temperature can be selected. Adding/removing laundry in standby mode If you want to add more laundry into the machine after the washing cycle has started, put the machine into “Pause” mode by pressing the “Start/Pause/ Cancel” button. The “Ready” lamp on the program follow-up indicator will light up after 1-2 minutes if the water level in the machine is suitable. Laundry may be added or taken out by opening the door. If the “Ready” lamp does not light up continuously at the end of this time, the water level in the machine is not suitable and laundry cannot be added. You can resume the program by pressing the “Start/Pause/Cancel” button again. Child-proof lockThere is a childproof lock to prevent any program interruption because of pressing the keys while the program is on. In order to activate the childproof lock, press on the 1st and 2nd auxiliary function keys from the left simultaneously for 3 seconds after the washing program has started. Child- proof lock lamp on the program follow- up indicator will light up when the child- proof lock is activated. To start a new program after the program is over or to interfere the program, childproof lock should be deactivated. To deactivate the child- proof lock, press the same buttons for 3 sec. Ending the program through canceling The program which is selected first will keep on going even if the position of the program selection button is changed. A new program can be selected or started after “Program is cancelled” in order to change the washing program. To cancel any selected program; • Press “Start/Pause/Cancel” button for 3 seconds. At the end of this time, “Start/Pause/Cancel” light and all lights go off and “Spin” lamp illuminates. If the door is unlocked, all lights on the indicator will go off and the “Ready” lamp will illuminate. You can select and start a new program when the “Ready” light is lit. • The machine can drain all the water or can take in water for 3 times at most to cool down the clothes and complete the draining process. Also the “Spin” light illuminates if the cancellation process is activated in the middle of the program. The “Spin” light goes off when discharging process is completed. The door can be opened and a new program can be selected when the “Lid” lamp illuminates. End of programThe “Ready” lamp on the program follow-up indicator will light up when the program comes to an end. The door can be opened and the machine becomes ready for a second cycle. Press the “On/Off” button to shut down the machine.
21 EN Preparation 1. Turn the tap on completely. Check if the hoses are connected tightly. 2. Place the laundry in the machine. 3. Add detergent and softener. Starting 1. Press the “On/Off” button. 2. Select the programme and the temperature. 3. If required (according to your machine’s model): – select any auxiliary function, – adjust the spin speed, – set the time delay, 4. Close the loading door. 5. Press “Start/Pause/Cancel” button. Canceling a program • Press “Start/Pause/Cancel” button for 3 seconds. At the end of this time, “Start/Pause/Cancel” light and all lights go off and “Spin” lamp illuminates. If the door is unlocked, all lights on the indicator will go off and the “Ready” lamp will light. You can select and start a new program when “Ready” light illuminates. • The machine can drain all the water or can take in water for 3 times at most to cool down the clothes and complete the draining process. Also the “Spin” light illuminates if the cancellation process is activated in the middle of the program. The “Spin” light goes off when discharging process is completed. The door can be opened and a new program can be selected when the “Ready” lamp illuminates. Adding more laundry • This is only possible under the following conditions: – during time delay, C You may add or remove laundry during the time delay (until the program starts). – At the beginning of a washing cycle, C Machine allows adding more laundry during a later step only if the water level is low enough to open the loading door or if the temperature in the machine is low enough. In order to add laundry after the start-up of the program: 1. Press “Start/Pause/Cancel” button. Wait until the door is allowed to open. When the “Ready” lamp is on continuously, continue to the next step. 2. Open the loading door and put in more laundry. 3. Close the loading door. 4. Press “Start/Pause/Cancel” button. Program is in rinse hold mode C Clothes may be left to soak in the machine as long as desired after filling during the last rinse step. When it reaches this position while the machine is running, the “Start/Pause/ Cancel” light will flash. If you wish to spin when the machine is in this mode: Press “Start/Pause/Cancel” button. Program resumes. Your machine drains the water and spins your laundry. If you want to discharge the water without spinning: • Press “Start/Pause/Cancel” button. The program continues and only drains the water. Re-spinning the laundry The control system for an unbalanced load can pause the spinning in cases when the distribution of the laundry in the drum is not balanced. If you want to re-spin the clothes: 1. Rearrange the previously placed clothes in machine. 2. Select the spin program. 3. Set the spin speed if spin speed adjustment is available on your machine. 4. Press “Start/Pause/Cancel” button. After the program is finished 1. “Ready” lamp will light up on the 6 Quick instructions for daily use
22 EN program follow-up indicator. Open the loading door and take out the clothes. 2. Press the “On/Off” button. 3. Turn the water tap off. 4. Eliminate any folding of the rubber seal on the loading door and check for impurities. 5. Leave the loading door and detergent drawer open to dry.
23 EN Detergent drawerRemove any powder residue buildup in the drawer. To do this; 1. Press the dotted point on the siphon in the softener compartment and pull towards you until the compartment is removed from the machine. C If more than a normal amount of water and softener mixture starts to gather in the softener compartment, the siphon must be cleaned. 2. Wash the dispenser drawer and the siphon with plenty of lukewarm water in a washbasin. Wear protective gloves or use an appropriate brush to avoid touching the residues in the drawer when cleaning. 3. Replace the drawer into its housing after cleaning. Check if the siphon is in its original location. The door and the drumAfter each wash: • Check if there are any foreign substances in the drum. • Open the hole in the bellow with the aid of a toothpick if it is clogged. C Foreign metal substances in your machine can cause rust stains. In such cases: Clean the drum with a stainless steel cleaning agent. Never use steel wool or wire wool. Outer cabinet and control panel When necessary: • Wipe the exterior panels of your machine with soapy water or mild detergent. Dry it with a soft cloth. • Use only a soft and damp cloth to clean the control panel. C Never use a sponge or scrubbing material. These will damage the painted and plastic parts. Inlet water filtersThere is a filter at the end of each water intake valve at the back side of the machine and also at the end of each water intake hose where they are connected to the tap. These filters prevent the foreign substances and dirt in the water to enter into the machine. Filters should be cleaned as they get dirty. • Close the taps. • Remove the nuts of the water intake hoses to clean the surfaces of the filters on the water intake valves with an appropriate brush. • If the filters are very dirty, you can pull them out by means of pliers and clean them. • Take out the filters on the flat ends of the water intake hoses together with the gaskets and clean thoroughly 7 Cleaning and care
24 EN under streaming water. • Replace the gaskets and filters carefully and tighten the hose nuts by hand. Draining any remaining water and cleaning the pump filter Filter system in your machine prevents solid items such as buttons, coins and fabric fibers clogging the pump propeller during discharging of the washing water. Thus, a good water discharger is achieved and the pump life is extended. • If your machine fails to drain the water, the pump filter may be clogged. You may have to clean it every 2 years or whenever it is blocked plugged. Water must be drained off to clean the pump filter. In addition, water may have to be drained off completely in the following cases: • before transporting the machine (e.g. when moving house) • when there is the danger of frost In order to clean the dirty filter and discharge the water; 1- Disconnect or unplug the machine from the power supply. A There may be water at 90°C in the machine. Therefore, the filter must be cleaned only after the inside water is cooled down to avoid hazard of scalding. 2- Open the filter cap. The filter cap may be composed of one or two pieces according to the model of your machine. If it is composed of two pieces, press the tab on the filter cap downwards and pull the piece out towards yourself. If it is composed of one piece, hold it from both sides and open it by pulling out. 3- An emergency drain hose is supplied with some of our models. Others are not supplied with this item. If your product is supplied with an emergency drain hose, do the following as shown in the figure below: • Pull out the pump outlet hose from its housing. • Place a large container at the end of the hose. Drain the water off into the container by pulling out the plug at the end of the hose. If the amount of water to be drained off is greater than the volume of the container, replace the plug, pour the water out, then resume the draining process. • After draining process is completed, replace the plug into the end of the hose and fit the hose back into its place. If your product is not supplied with an emergency drain hose, do the following as shown in the figure below: • Place a large container in front of the
25 EN filter to receive water flowing from the filter. • Loosen pump filter (anticlockwise) until water starts to flow out of it. Direct the flowing water into the container you have placed in front of the filter. You can use a piece of cloth to absorb any spilled water. • When there is no water left, turn the pump filter until it is completely loose and remove it. • Clean any residues inside the filter as well as fibers, if any, around the propeller region. • If your product has a water jet feature, be sure to fit the filter into its housing in the pump. Never force the filter while replacing it into its housing. Fit the filter fully into its housing; otherwise, water may leak from the filter cap. 4- Close the filter cap. Close the two-piece filter cap of your product by pushing the tab on it. Close the one-piece filter cap of your product by fitting the tabs on the bottom into their positions and pushing the upper part of it.
26 EN ProblemCause Explanation / Suggestion Program cannot be started or selected. Machine may have switched to self protection mode due to an infrastructure problem (such as line voltage, water pressure, etc.). Reset your machine by pressing “Start/Pause/ Cancel” button for 3 seconds. (see, Cancelling a Program) Water in the machine. There may be some water in your machine when you receive it. This is from the quality control process and is normal. It is not harmful to your machine. There is water coming from the bottom of the machine. There might be problems with hoses or the pump filter. Be sure the seals of the water inlet hoses are securely fitted. Tightly attach the drain hose to the waste pipe or sink. Make sure that the pump filter is completely closed. Machine does not fill with water. Tap may be turned off. Open the inlet water taps fully. Water inlet hose might be bent. Straighten the water intake hose. Water inlet filter might be clogged. Clean the water intake filter. The door may be ajar. Close the door. Machine does not discharge water. Water outlet hose might be clogged or twisted. Clean or straighten the hose. Pump filter may be clogged. Clean the pump filter. Machine vibrates or shakes. Machine feet might require adjustment. Adjust the machine feet. Transportation safety bolts might have not been removed. Remove the transportation safety bolts. There may be a small amount of laundry in the machine. Add more laundry to the machine. The machine may be overloaded or the clothes may be distributed unevenly. Reduce the amount of laundry in the machine or balance the load by hand. There machine might be touching a solid surface Ensure that nothing touches the machine. Machine stopped shortly after the program started. Machine can stop temporarily due to low voltage. It will resume operating when the voltage is back to the normal level. The water being taken in is directly discharged. Improper position of the drain hose. Connect the water draining hose as described in the operation manual. 8 Troubleshooting