Beko Ev 5800y Manual
Have a look at the manual Beko Ev 5800y Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 187 Beko manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
11 / EN 4 Operating the product 4.1 Control panel 1 2 34 5 1 - Programme Selection knob (Uppermost position On / Off) 2 - Door open indicator 3 - Programme Follow-up indicator 4 - Start / Pause button 5 - Spin Speed Adjustment button 4.2 Preparing the machineMake sure that the hoses are connected tightly. Plug in your machine. Turn the tap on completely. Place the laundry in the machine. Add detergent and fabric softener. Programme selectionSelect the programme suitable for the type, quantity and soiling degree of the laundry in accordance with the "Programme and consumption table" and the temperature table below. Select the desired programme with the Programme Selection button. 90˚C Heavily soiled white cottons and linens. (coffee table covers, tableclothes, towels, bed sheets, etc.) 60˚C Normally soiled, coloured, fade proof linens, cottons or synthetic clothes (shirt, nightgown, pajamas, etc.) and lightly soiled white linens (underwear, etc.) 40˚C- 30˚C- Cold Blended laundry including delicate textile (veil curtains, etc.), synthetics and woolens. CINFORMATIONS Use an anti-limesc Programmes are limited with the highest spin speed appropriate for that particular type of fabric. ale suitable for the washing machines. When selecting a programme, always consider the type of fabric, colour, degree of soiling and permissible water temperature. For further programme details, see “Programme and consumption table”. 4.3 Main programmes Depending on the type of fabric, use the following main programmes. • Cottons Use this programme for your cotton laundry (such as bed sheets, duvet and pillowcase sets, towels, bathrobes, underwear, etc.). Your laundry will be washed with vigorous washing action for a longer washing cycle. • Synthetics Use this programme to wash your synthetic clothes (shirts, blouses, synthetic/cotton blends, etc.). It washes with a gentle action and has a shorter washing cycle compared to the Cotton programme. For curtains and tulle, use the Synthetic 40˚C programme. As their meshed texture causes excessive foaming, wash the veils/tulle by putting little amount of detergent into the main wash compartment. Do not put detergent in the prewash compartment. • Woollens Use this programme to wash your woolen clothes. Select the appropriate temperature complying with the tags of your clothes. Use appropriate detergents for woolens. 4.4 Additional programmes For special cases, additional programmes are available in the machine. CINFORMATIONS Additional programmes may differ according to the model of the machine. • Cotton Economic Use this programme to wash your laundry washable in cottons programme for a longer time, still with a very good performance for saving purposes. Washing Machine / User’s Manual
12 / EN CINFORMATIONS Cottons Eco programme consumes less energy compared to other cottons programmes. • Delicate Use this programme to wash your delicate clothes. It washes with a gentle action without any interim spin compared to the Synthetics programme. • Hand wash Use this programme to wash your woolen/delicate clothes that bear “not machine- washable” tags and for which hand wash is recommended. It washes laundry with a very gentle washing action to not to damage clothes. • Mini 30 Use this programme to wash your lightly soiled cotton clothes in a short time. • Prewash Cotton Prefer this programme only for heavily soiled cotton clothes. CINFORMATIONS Not using this programme with prewash will save energy, water, detergent and time. 4.5 Special programmesFor specific applications, select any of the following programmes. • Rinse Use this programme when you want to rinse or starch separately. • Spin + Drain Use this programme to apply an additional spin cycle for your laundry or to drain the water in the machine. CINFORMATIONS If you wish to drain the water only without spinning your laundry, select the Spin+Pump programme and press “Start / Pause” button. Machine will switch to spin step once it completes the program step. Press “Start / Pause” button to stop the machine as soon as you see the drum rotating. And cancel this programme by turning Programme Selection knob to any other position. Washing Machine / User’s Manual
13 / EN 4.6 Programme and consumption table • : Selectable ** : Energy Label programme (EN 60456 Ed. 3) ***: If maximum spin speed of the machine is lower then this value, you can only select up to the maximum spin speed. CINFORMATIONS Water and power consumption may vary subject to the changes in water pressure, water hardness and temperature, ambient temperature, type and amount of laundry, selection of auxiliary functions and spin speed, and changes in electric voltage. ** “Cotton Economic 40°C and Cotton Economic 60°C are standard cyc\ les.” These cycles are known as ‘40°C cotton standard cycle’ and ‘60°C cotton standard cycle’ and indicated with the symbols on the panel. EN 2 Programme Max. Load (kg) Programme Duration (~min) Water Consumption (l) Energy Consumption (kWh) Max. Speed*** Cottons 905130 531.631400 Prewash-Cottons 605115 641.101400 Cottons 405120 500.971400 Cottons Cold5120 520.101400 Cotton Economic 60**5145 450.801400 Cotton Economic 60**2.5145 380.751400 Cotton Economic 40**2.5116 380.651400 Synthetics 602.5113 551.02800 Synthetics 402.5105 540.50800 Synthetics Cold2.566 520.10800 Delicate 30261 470.26800 Woollens 401.5 54 500.35800 Hand wash 20141 340.20800 Mini 30 302.5 29 720.211400 Washing Machine / User’s Manual
14 / EN 4.7 Starting the programmePress Start / Pause button to start the programme. Programme follow-up light showing the startup of the programme will turn on. Progress of programmeProgress of a running programme can be followed from the Programme Follow-up indicator with the lights "Running" and "End/Cancel". CINFORMATIONS If the machine does not pass to the spinning step, automatic unbalanced load detection system might have been activated due to the unbalanced distribution of the laundry in the machine. 4.8 Loading door lockThere is a locking system on the loading door of the machine that prevents opening of the door in cases when the water level is unsuitable. If you want to open loading door when the machine is in use, press "Start / Pause" button to pause the machine. "Door Open" light will start flashing when the machine is switched to Pause mode. Machine checks the level of the water inside. If the level is suitable, "Door Open" light illuminates steadily within 1-2 minutes and the loading door can be opened. If the level is unsuitable, "Door Open" light turns off and the loading door cannot be opened. If you are obliged to open the loading door when the "Door Open" light is off, you have to cancel the current programme; see "Cancelling the programme". Switching the machine to pause modePress the "Start / Pause" button to switch the machine to pause mode while a programme is running. "Running" light starts flashing on the Programme Follow-up indicator to show that the machine has been switched to the pause mode. When the loading door is ready to be opened, "Door Open" light will illuminate continuously. Adding or taking out laundryPress "Start / Pause" button to switch the machine to pause mode. When the machine is switched to pause mode, "Running" light flashes. Wait until the Loading Door can be opened. Open the Loading Door and add or take out the laundry. Close the Loading Door. Press "Start / Pause" button to start the machine. CINFORMATIONS The door can be opened if the water level is suitable. Door open symbol flashes until the loading door gets ready to be opened. The symbol’s light is steady when the door is ready to open. You can open the door to add/take out laundry. 4.9 Cancelling the programmeTo cancel the programme, turn the Programme Selection knob to select another programme. Previous programme will be cancelled. "End/Cancel" light will flash continuously to notify that the programme has been cancelled. CINFORMATIONS If you start a new programme after cancelling the previous one, this new programme will start without draining the water in the machine. If you must certainly open the loading door when the “Door Open” light is off, you need to use “Spin+Pump” programme. See “Spin+Pump” Re-spinning the laundry Unbalanced load control system can prevent spinning because of unbalanced load of laundry in the machine. If you would like to spin again: Rearrange the laundry in the machine. Select Spin+Pump programme and press “Start / Pause" button. 4.10 End of programme"End/Cancel" light on the programme follow-up indicator will light up once the programme comes to an end; and "Door Open" symbol flashes for 1-2 minutes until the door is ready to open. When "Door Open" symbol is steadily illuminated, the door can be opened. To turn off the machine, turn program selection knob to "On / Off" position. Take out your laundry and close the loading door. The machine will be ready for the next run. 4.11 Door Open"Door Open" symbol is illuminated when the door is ready to open. It flashes until the door gets ready to open. If the "Door Open" symbol is not illuminated, do not force the door to open. The symbol's light is steady when the door is ready to open. 4.12 Your machine is equipped with a “Standby Mode” In case of not starting any programme or waiting without making any other operation when the machine is turned on by On/Off button and while it is in selection step or if no other operation is performed approximately 2 minutes after the programme you selected has come to an end, your machine will automatically switch to energy saving mode. Brightness of indicator lights will decrease. Also, if your product is equipped with a display showing the programme duration, this display will completely turn off. In case of rotating the Programme Selection knob or pressing any button, lights and display will restore to their previous condition. Your selections made while exiting the energy saving mode may change. Check the appropriateness of your selections before starting the programme. Readjust if necessary. This is not a fault. Washing Machine / User’s Manual
15 / EN If the holes on the bellow shown in the figure is blocked, open the holes using a toothpick. CINFORMATIONS Foreign metal substances will cause rust stains in the drum. Clean the stains on the drum surface by using cleaning agents for stainless steel. Never use steel wool or wire wool. 5.3 Cleaning the body and control panelWipe the body of the machine with soapy water or non- corrosive mild gel detergents as necessary, and dry with a soft cloth. Use only a soft and damp cloth to clean the control panel. AWARNING Never use sponge or scrub materials. These will damage the painted and plastic surfaces. 5.4 Cleaning the water intake filtersThere is a filter at the end of each water intake valve at the rear of the machine and also at the end of each water intake hose where they are connected to the tap. These filters prevent foreign substances and dirt in the water to enter the washing machine. Filters should be cleaned as they do get dirty. Close the taps. Remove the nuts of the water intake hoses to access the filters on the water intake valves. Clean them with an appropriate brush. If the filters are too dirty, take them 5 Maintenance and cleaning Service life of the product extends and frequently faced problems decrease if cleaned at regular intervals. 5.1 Cleaning the detergent drawerClean the detergent drawer at regular intervals (every 4-5 washing cycles) as shown below in order to prevent accumulation of powder detergent in time. Press the dotted point on the siphon in the softener compartment and pull towards you until the compartment is removed from the machine. CINFORMATIONS If more than normal amount of water and softener mixture starts to gather in the softener compartment, the siphon must be cleaned. Wash the detergent drawer and the siphon with plenty of lukewarm water in a washbasin. Wear protective gloves or use an appropriate brush to avoid touching of the residues in the drawer with your skin when cleaning. Insert the drawer back into its place after cleaning and make sure that it is seated well. 5.2 Cleaning the loading door and the drumFor products with drum cleaning programme, please see Operating the product - Programmes. For products without drum cleaning, follow the below steps to clean the drum: Select Additional Water or Extra Rinse auxiliary functions. Use a Cottons programme without pre-wash. Set the temperature to the level recommended on the drum cleaning agent which can be provided from authorized services. Apply this procedure without any laundry in the product. Before starting the programme, put 1 pouch of special drum cleaning agent (if the special agent could not be supplied, put max. 100 g of powder anti-limescale) into the main wash detergent compartment (compartment no. “2”). If the anti-limescale is in tablet form, put only one tablet into the main wash compartment no. “2”. Dry the inside of the bellow with a clean piece of cloth after the programme has come to an end. CINFORMATIONS Repeat Drum Cleaning process in every 2 months. Use an anti-limescale suitable for the washing machines. After every washing make sure that no foreign substance is left in the drum. Washing Machine / User’s Manual
16 / EN out by means of pliers and clean them. Take out the filters on the flat ends of the water intake hoses together with the gaskets and clean thoroughly under running water. Replace the gaskets and filters carefully in their places and tighten the hose nuts by hand. 5.5 Draining remaining water and cleaning the pump filter The filter system in your machine prevents solid items such as buttons, coins and fabric fibers clogging the pump impeller during discharge of washing water. Thus, the water will be discharged without any problem and the service life of the pump will extend. If the machine fails to drain water, the pump filter is clogged. Filter must be cleaned whenever it is clogged or in every 3 months. Water must be drained off first to clean the pump filter. In addition, prior to transporting the machine (e.g., when moving to another house) and in case of freezing of the water, water may have to be drained completely. AWARNING Foreign substances left in the pump filter may damage your machine or may cause noise problem. In order to clean the dirty filter and discharge the water: Unplug the machine to cut off the supply power. AWARNING Temperature of the water inside the machine may rise up to 90 ºC. To avoid burning risk, filter must be cleaned after the water in the machine cools down. Open the filter cover by pulling it from both sides at the top. CINFORMATIONS You can remove the filter cover by slightly pushing downwards with a thin plastic tipped tool, through the gap above the filter cover. Do not use metal tipped tools to remove the cover. Follow the steps below to discharge the water. Place a large container in front of the filter to catch water from the filter. Loosen pump filter (anticlockwise) until water starts to flow. Fill the flowing water into the container you have placed in front of the filter. Always keep a piece of cloth handy to absorb any spilled water. When the water inside the machine is finished, take out the filter completely by turning it. Clean any residues inside the filter as well as fibers, if any, around the pump impeller region. Install the filter. Seat the tabs in the lower part into their places first, and then press the upper part to close. Washing Machine / User’s Manual
17 / EN EV 5800 +Y5 84 60 41.5 55 230 V / 50Hz 10 1550 800 1.00 0.20 9413 • / - 6 Technical specifications CINFORMATIONS Technical specifications may be changed without prior notice to improve the quality of the product.\ Figures in this manual are schematic and may not match the product exactly. Values stated on the product labels or in the documentation accompanying it are obtained in laboratory conditions in accordance with the relevant standards. Depending on operational and environmental conditions of the product, these values may vary. Models (EN) Maximum dry laundry capacity (kg) Height (cm) Width (cm) Depth (cm) Net weight (±4 kg.) Electrical input (V/Hz) Total current (A) Total power (W) Spin speed (rpm max.) Stand-by mode power (W) Off-mode power (W) Main model code Single Water inlet / Double Water inlet • Available Dark wash Dark washSynthetics CottonsPre-wash Main wash Rinse WashSpin Drain Anti- creasing Duvet Child- proof lock Hand Wash Baby Cotton Eco Woolens Delicates Pet hair removal Daily Lingerie expres 14 Super short express Daily express Rinse hold Start/ Pause No spin Quick wash Finished Cold Self Clean Temperature Mixed 40 Super 40Extra rinse Freshen up Shirts JeansSportTime delay Intensive Fasion care mini 30 Washing Machine / User’s Manual
18 / EN 7 Troubleshooting Program does not start after closing the door. • Start / Pause / Cancel button was not pressed.>>> *Press the Start / Pau\ se / Cancel button. Programme cannot be started or selected. • Washing machine has switched to self protection mode due to a supply problem (line voltage, water pressure, etc.). >>> To cancel the programme, turn the Programme Selection knob to select another programme. Previous programme will be cancelled. (See "Cancelling the programme") Water in the machine. • Some water might have remained in the product due to the quality control processes in the p\ roduction. >>> This is not a failure; water is not harmful to the machine. Machine vibrates or makes noise. • Machine might be standing unbalanced. >>> Adjust the feet to level the machine.• A hard substance might have entered into the pump filter. >>> Clean the pump filter.• Transportation safety bolts are not removed. >>> Remove the transportation safety bolts.• Laundry quantity in the machine might be too little. >>> Add more laundry to the machine.• Machine might be overloaded with laundry. >>> Take out some of the laundry from the machine or distribute the load by hand to balance it homogenously in the machine. • Machine might be leaning on a rigid item. >>> Make sure that the machine is not leaning on anything. Machine stopped shortly after the programme started. • Machine might have stopped temporarily due to low voltage. >>> It will resume running when the voltage restores to the normal level. Programme time does not countdown. (On models with display) • Timer may stop during water intake. >>> Timer indicator will not countdown until the machine takes in adequate amount of water. The machine will wait until there is sufficient amount of water to avoid poor washing results due to lack of water. Timer indicator will resume countdown after this. • Timer may stop during heating step. >>> Timer indicator will not countdown until the machine reaches the selected temperature. • Timer may stop during spinning step. >>> Automatic unbalanced load detection system might be activated due to the unbalanced distribution of the laundry in the drum. CINFORMATIONS Machine does not switch to spinning step when the laundry is not evenly distributed in the drum to prevent any damage to the machine and to its surrounding environment. Laundry should be rearranged and re-spun. Foam is overflowing from the detergent drawer. • Too much detergent is used. >>> Mix 1 tablespoonful softener and ½ l water and pour into the main wash compartment of the detergent drawer. CINFORMATIONS Put detergent into the machine suitable for the programmes and maximum loads indicated in the “Programme and consumption table”. When you use additional chemicals (stain removers, bleachs and etc), reduce the amount of detergent. Laundry remains wet at the end of the programme • Excessive foam might have occurred and automatic foam absorption system might have been activated due to too much detergent usage. >>> Use recommended amount of detergent. CINFORMATIONS Machine does not switch to spinning step when the laundry is not evenly distributed in the drum to prevent any damage to the machine and to its surrounding environment. Laundry should be rearranged and re-spun. AWARNING If you cannot eliminate the problem although you follow the instructions in this section, consult your dealer or the Authorized Service Agent. Never try to repair a nonfunctional product yourself. Washing Machine / User’s Manual
2820523382_HR/ 31-08-15.(10:35)Broj Dokumenta= Perilica rublja Korisnički priručnik EV 5800 +Y HRSL
Ovaj je proizvod proizveden koristei najnoviju tehnologiju u ekološki prihvatljivim uvjetima.