Beko Dfn 6833 B Manual

							28
Adjusting the height of empty 
upper basket
(depends on the model)
You can adjust the height of the upper 
basket according to the size of the dish 
to be washed. Use basket rollers to 
change the basket height. 
1. Turn the stoppers on the ends of 
the upper basket rails by turning 
them aside (A). 
2. Take the basket out (B). 
3. Change the position of the rollers, 
place the basket into the rail and 
close the stoppers (C).
1022 eps
\037
\036
\035 
EN  
						

							29
5Operating the product
1. On/Off key
2. Start / Pause / Cancel key
3. Display
4. Programme Selection key
5. Half Load key
6. Express key 
7. Tablet Detergent key
8. Time Delay key
9. Handle
10. Programme indicator
11 .  Remaining Time / Delay Time 
indicator
12. Start / Pause indicator
13. Time Delay indicator
14. Rinse Aid  indicator
15. Half Load “” indicator
16. Express indicator 
17. Tablet Detergent indicator
18. Salt indicator
19. Child Lock indicator
20. Programme Steps Follow-up 
indicators
 a Washing Step indicator “”
 b Rinsing Step indicator “”
 c Drying Step indicator “”
 d End of Programme indicator “”
\037\036
\037\035
\037\034
\037\037\037\033
\037\032\037\031
\037\030
\037\027
\026\025 \024\023
\035\036
\037\022
\037\036\035\034
\033\032\031\030
\027 
EN  
						

							30
Keys
On / Off key
It is used to turn on or off the machine. 
In On position, the machine switches 
on with the last programme in use. In 
Of position, indicators on the display 
will turn off.
If the Half Load, Tablet Detergent, 
Child Lock and Time Delay functions 
were selected in the previous 
programme used, these functions will 
remain active when the machine is 
turned off and on again. If you want to 
disable these functions after turning the 
machine off and on again, you must 
press the relevant keys again.
Start / Pause / Cancel key
It is used to start, pause or cancel the 
selected programme or function.
To press the Start / Pause / Cancel 
key, wait for two seconds after you turn 
on the machine by pressing the On 
/ Off key. An image will be displayed 
within this time.
Programme Selection key
It is used to choose the washing 
programme you selected in the “Table 
of Programme Data and Average 
Consumption Values”.
Half Load key
It is used to operate the machine 
without loading it completely. 
1. Load your dishes in the machine as 
you like.
2. Press the On / Off key. 
3. Select the desired programme and 
press the Half Load key. Half Load 
() indicator will appear on the 
display.
4. Press Start / Pause / Cancel key to 
start the programme. 
C With the Half Load function you 
can save both water and power 
while using the lower and upper 
baskets of the machine.
Tablet Detergent key
This function provides better drying 
performance with the multi-purpose 
detergents such as 2in1, 3in1, 4in1, 
5in1, all in one, etc., depending on the 
hardness level of the supply water. Look 
at the “Table of Programme Data and 
Average Consumption Values” to see 
which programmes the Tablet Detergent 
function can be used with. 
C Tablet Detergent Indicator  lights 
when the Tablet Detergent function 
is selected.
Time Delay key
It is used to select the Time Delay 
function. You can delay the start of the 
selected programme up to 24 hours with 
increments of 30 minutes thanks to the 
Time Delay function.
Express key
This option allows you to shorten the 
selected programme; the dishwasher 
then uses higher water pressure and 
consumes less energy and water.
Preparing the machine
1.  Open the tap.
2. Plug in to the socket.
3. Open the door of the dishwasher.
4. Place the dishes in accordance with 
the instructions in the user manual.
5. Make sure that the upper and lower 
impellers rotate freely.
6. Put adequate amount of detergent 
into the detergent dispenser.
7. Check if the Salt and Rinse Aid 
indicators light and add salt and/or 
rinse aid if needed.
8. Close the door of the dishwasher. 
EN  
						

							31
Programme selection
1. Press On / Off key to turn on your 
machine.
2. Refer to “Table of Programme Data 
and Average Consumption Values” 
to select a washing programme 
suitable for your dishes.
3. Press Programme Selection key 
 repeatedly until the number of 
the selected programme appears 
on the Programme indicator 
. Programme number 
will increase by one each time you 
press the key. 
C Number of the programmes on the 
machine may change depending 
on the model you have purchased.
Adding an auxiliary function 
to the programme
Depending on your needs, you can 
add Half Load (1/2), Tablet Detergent, 
Express and Time Delay functions to 
the programme you have selected.
Press the key of the function you 
wish to add. Indicator of the relevant 
function will appear on the display.
Setting Time Delay function
If an economical electricity tariff is 
applied in your region, you can use 
the Time Delay function to wash your 
dishes during appropriate hours.
1.  Press the Time Delay function 
key after selecting the washing 
programme and other auxiliary 
functions. Time Delay indicator () 
will start flashing on the display. 
2. Press Time Delay key to set the 
time you wish. Time will increase 
with increments of 30 minutes up to 
24 hours every time you press the 
key.
3. Press Start / Pause / Cancel key. 
Delay time will start countdown. 
Time Delay indicator () and 
Start / Pause indicator will light 
continuously. Remaining time will 
appear on the Time Delay indicator. 
Programme will start automatically 
when the countdown is over.
Changing the settings during Time 
Delay
While the Time Delay function is 
activated, you can make changes 
in the washing programme, other 
auxiliary functions or the delay time. 
1.  Press Start / Pause / Cancel key 
to switch the machine into Pause 
mode. Countdown will stop.
2. Select the new programme, 
auxiliary functions and time as 
described in the sections above. 
3. Press Start / Pause / Cancel key. 
Countdown will resume or restart.
Canceling the Time Delay function
1. Press and hold Start / Pause / 
Cancel key for 3 seconds. 
2. Release the key when the Start / 
Pause indicator starts flashing. For 
a couple of minutes the machine 
will fulfill the necessary operations 
required to cancel the function. 
Once the Time Delay function is 
cancelled, “00:00” will appear on 
the Remaining Time indicator.
C You can select and start a 
new programme following the 
cancellation of Time Delay function.
C Time Delay function can not be set 
after the programme starts.
Starting the programme
To start your machine after selecting 
the programme and auxiliary functions, 
press Start / Pause / Cancel key. 
Once the programme starts to run, 
Remaining Time indicator displays  
EN  
						

							32
YM_program_
takibi
the estimated time to the end of the 
programme. Start / Pause indicator 
starts lighting continuously.
C Your machine performs water 
softening depending on the hardness 
level of the supply water. Remaining 
time displayed towards the end in 
some programmes can be different 
from the time indicated at the 
beginning due to this process. The 
total time can also change while the 
programme is running depending on 
the ambient temperature where your 
machine is installed, temperature of 
the supply water and amount of the 
dishes.
C Pay attention not to open the door 
of the machine when it is running. 
Stop the machine by pressing Start 
/ Pause / Cancel key if you have to 
open the door. Then, open the door 
of the machine. There may be a rush 
of vapour when you open the door 
of your machine; be careful. Close 
the door of your machine and press 
Start / Pause / Cancel key again. 
Programme will resume running.
Child Lock
You can prevent other people 
from interrupting and changing the 
programme cycle and delay time while 
the machine is running.
1.   Press and hold the Programme 
Selection key and the Half Load key 
simultaneously for three seconds to 
activate the child lock. Child Lock 
indicator will appear on the display. 
Repeat the same procedure to 
disable the Child Lock. 
C Child lock prevents the selected 
programme or functions from being 
changed and disables the Start / 
Pause / Cancel key.
C Child Lock does not lock the door 
of the machine.
Programme follow-up
You can follow-up the washing step 
in which the current programme is in 
from the Programme Steps Follow-up 
indicators on the display.
a  Washing Step indicator
b Rinsing Step indicator
c Drying Step indicator
d End of Programme indicator
Indicators for Washing, Rinsing and 
Drying will light respectively on the 
display while the selected programme 
is running. Only the End of Programme 
indicator lights up when the 
programme is over. “00:00” appears on 
Remaining Time indicator.
Canceling a programme
1. Press and hold Start / Pause / 
Cancel key for 3 seconds while the 
programme is running. 
2. Release the key when the Start / 
Pause indicator  starts flashing. 
For a couple of minutes the 
machine will fulfill the necessary 
operations required to cancel the 
programme. Once the Time Delay 
function is cancelled, “00:00” will 
appear on the Remaining Time 
indicator.
\037\036\035\034
\033\032 
EN  
						

							33
C You can select and operate a 
new programme following the 
cancellation of the programme.
C There might be residues of 
detergent or rinse aid left in the 
machine and/or on the pieces 
being washed depending on the 
step the previous programme was 
in at the time of such cancellation.
Salt indicator
Check the Salt indicator on the display 
to see whether there is enough 
softening salt in your machine or not. 
You need to refill the salt container 
whenever the Salt indicator lights.
C If the water hardness level is saved 
as (r1), Salt indicator will never 
come on even if the salt container 
is empty. (Adjusting the water 
hardness level is explained in 
Water Softening System section.) 
Rinse Aid indicator
Check the Rinse Aid indicator on the 
display to see whether there is enough 
softening rinse aid in your machine 
or not. You must refill the rinse aid 
container when the Rinse Aid indicator 
comes on. 
C If the Rinse Aid indicator is set 
to OFF, Rinse Aid indicator will 
never come on even if the rinse aid 
container is empty.
Setting the Rinse Aid indicator
1.  Turn on your machine by pressing 
On / Off key while pressing and 
holding the Half Load () key 
when the machine is in off position. 
Keep holding the keys pressed in 
this stage.
2. Release On / Off (1) key while 
pressing and holding the Half Load 
() key.
3. Keep the Half Load () key 
pressed for three seconds more.
4. Rinse Aid indicator lights up and 
the Rinse Aid indicator status 
saved on your machine appears on 
the display as “ON” or “OFF”.
5. You can change the status of the 
indicator as “ON” or “OFF” by 
pressing the Start / Pause / Cancel 
key. 
C If you switch off the machine with 
“On/Off” key when the status is 
“ON”, then the Rinse Aid indicator 
will come on when the rinse aid 
level in your machine becomes low 
while the machine is in use. If you 
switch off the machine by pressing 
On/Off key when the status is set 
to OFF, then the Rinse Aid indicator 
will never come on.
End of programme
End of Programme indicator will light 
up once the washing programme 
is over.
1.  Press On / Off key to turn off your 
machine.
2. Close the tap.
3. Unplug the machine from the 
socket.
C Leave your dishes in the machine 
for about 15 minutes to cool down 
after they are washed. Your dishes 
will dry in a shorter time if you 
leave the door of your machine ajar 
during this period. This process will 
increase the drying effectiveness of 
your machine. 
EN  
						

							34
Programme Table
Programme number
1
2
3 Reference*
4
5
6
7
8
Programme name
Cleaning temperature
Degree of Soiling
 Suitable for removing the remnants on the soiled dishes that will be kept waiting in the machine for a few days, and thus, for preventing the bad odor buildup.
Suitable for lightly soiled daily dishes that are scraped or pre-cleaned.  
Most economical washing program for the medium soiled daily dishes that are kept waiting.  
Daily washing program at which the medium soiled dishes that are kept waiting are cleaned in the fastest way. 
Suitable for heavily soiled dishes, pots 
and pans.  
Suitable for the dishes which require extra hygiene such as articles for babies. Also suitable for heavily soiled 
dishes. 
The best suitable program for the mixed nature of the daily dishes. Glass and crystal utensils are washed sensitively in the upper basket while the pots and pans are washed powerfully in the 
lower basket. 
Determines the soiling degree of the dishes and sets the temperature and amount of the washing water as well as the washing time automatically. Suitable for all types of dishes.
-
Few
Medium
Medium
High
High
Medium
Medium to high
Detergents
 
A=25 cm³/15 cm³ B=5 cm³
-
A
A+B
A+B
A+B
A+B
A+B
A
Programme sequence
 
(without options)
Pre-wash
 
▼ End
Wash
 
▼ 
Cold rinse
 
▼ 
Hot Rinse
 
▼ End
Pre-wash
 
▼ 
Wash
 
▼ 
Cold rinse
 
▼ 
Hot Rinse
 
▼ Dry ▼ End
Wash
 
▼ 
Cold rinse
 
▼ 
Hot Rinse
 
▼ Dry ▼ End
Pre-wash
 
▼ 
Wash
 
▼ 
Cold rinse
 
▼ 
Hot Rinse
 
▼ Dry ▼ End
Pre-wash
 
▼ 
Wash
 
▼ 
Cold rinse
 
▼ 
Hot Rinse
 
▼ 
Hot Rinse
 
▼ Dry ▼ End
Pre-wash
 
▼ 
Wash
 
▼ 
Cold rinse
 
▼ 
Hot Rinse
 
▼ 
Hot Rinse
 
▼ Dry ▼ End
The programme 
sequence is adjusted to the amount of soiling
Duration (min)
15
30
189
58
143
124
177
80-154
Water (I)
4
10,4
10
10,2
16,2
17,8
18,6
10,4-14,2
Energy (kWh)
 -
0,8
0,92
1,32
1,26
1,97
1,36
0,90-1,42
The consumption values shown in the table were determined under standard\
 conditions. Differences may therefore occur under practical conditions.
 
* Reference programme for testing institutes The tests in accordance with EN 50242 must be carried out with a full wa\
ter softener salt dispenser and a full rinse aid reservoir, and using the test programme.
Mini 30'
Pre-wash
 
Eco
Quick & Clean
Intensive
Baby Protect
Active Wash
Auto
35°C
-
50°C
60°C
70°C
70°C
70°C
40°C- 65°C 
EN  
						

							35
1. Turn the micro filter (3) and 
coarse filter (2) assembly counter 
clockwise and pull it out from its 
seating (A).
6Maintenance and cleaning
Service life of the product extends and 
frequently faced problems decrease if it 
is cleaned at regular intervals. 
A Unplug the product and turn off the 
tap before attempting any cleaning 
procedures.
C  Do not use abrasive substances for 
cleaning.
C Clean the filters and impellers at 
least once a week.
Cleaning the outer surface of 
the product
Clean the outer surface and door 
gaskets of the product gently with a mild 
cleaning material and damp cloth. Wipe 
the control panel only with a damp cloth.
Cleaning the interior of the 
machine
—  Clean the interior of the machine 
and the tank by running a prewash 
programme without detergent or 
a long washing programme with 
detergent based on the degree of 
soiling.
— If water has remained in the 
machine, drain the water by 
performing the procedures under 
the topic "Canceling a programme". 
If the water cannot be discharged, 
clean any leftover deposits that 
have piled up in the bottom of the 
machine, blocking the water path. 
Cleaning the filters
Clean the filters at least once a week 
in order for the machine operates 
efficiently. Check if food residues are left 
on the filters. If there are food residues 
on filters, take them out and clean well 
under running water.
1031
\037
\036
\035
\034
\033
\032
\037
\036
\035
\034
\033
\032
\037
\036
\035
\034
\033
\032
2.  Pull out the metal / plastic filter (1) 
(B). 
EN  
						

							36
\037
\036
\035
\034
\033
\032
4.  Clean all three filters under tap 
water by means of a brush.
5. Replace the metal/plastic filter.
6. Place the coarse filter into the 
microfilter. Make sure that it is 
properly seated. Turn the coarse 
filter clockwise until a “click” sound 
is heard. 
A Do not use the dishwasher without 
filter.
C  Incorrect placement of the filters 
will reduce washing efficiency.
Cleaning the hose filter
Damages on the machine that may be 
caused by impurities coming from the 
urban supply water or your own water 
installation (such as sand, dirt, rust, 
etc.) can be prevented by means of the 
filter attached to the water inlet hose. 
Check the filter and the hose regularly 
and clean them if necessary.
1.  Turn off the tap and remove the 
hose.
2. After taking out the filter, clean it 
under running tap water.
3. Place the cleaned filter back to its 
seat in the hose.
4. Install the hose to tap.
\037
\036
\035
\034
\033
\032
\037
\036
\035
\034
\033
\032
3. Press the two pawls on the coarse 
filter inwards and separate the 
coarse filter from the assembly (C).
Cleaning the impellers
Clean the impellers at least once a 
week in order for the machine operates 
efficiently. 
Lower impeller
Check if the holes on the lower impeller 
(1) are clogged. If they are clogged, 
remove and clean the impeller. Pull the 
lower impeller up to remove it (A, B). 
EN  
						

							37
1032
Upper impeller
Check if the holes on the upper 
impeller (2) are clogged. If they 
are clogged, remove and clean the 
impeller. Turn its nut to left to remove 
the upper impeller (C, D).
Make sure that the nut is tightened well 
when installing the upper impeller. 
\037
\036
\035
\034
\033
\032 
EN