Beko 5120 W Manual

EN21
auxiliary function, but you cannot 
select pre-wash.
C   The spin speed and temperature 
which are selected first will keep on 
being valid even if the position of the 
spin speed or temperature selection 
knob	is	changed.	Press	“Start/
Pause/Cancel”	button	and	switch	
the	machine	to	“Pause”	mode	in	
order to change the spin speed or 
temperature. New spin speed or 
temperature can be selected.  
Adding/removing laundry in standby 
mode
If you want to add more laundry into the 
machine after the...

EN22
Preparation
1. Turn the tap on completely. Check if 
the hoses are connected tightly.
2.	 Place	the	laundry	in	the	machine.
3.  Add detergent and softener.
Starting
1.	 Press	the	“On/Off”	button.
2.  Select the programme and the 
temperature.
3.	 If	required	(according	to	your	 machine’s	model):
–	 select	any	auxiliary	function,
–	 adjust	the	spin	speed,
–	 set	the	time	delay,
4.  Close the loading door.
5.	 Press	“Start/Pause/Cancel”	button.
Canceling a program
•	 	Press	“Start/Pause/Cancel”	button...

EN23
Detergent drawer
Remove any powder residue buildup in 
the	drawer.	To	do	this;
1.	 Press	the	dotted	point	on	the	siphon in the softener compartment 
and pull towards you until the 
compartment is removed from the 
machine.
C  If more than a normal amount of 
water and softener mixture starts to 
gather in the softener compartment, 
the siphon must be cleaned.
2.  Wash the dispenser drawer 
and the siphon with plenty of 
lukewarm water in a washbasin. 
Wear protective gloves or use an 
appropriate...

EN24
dirty.
•	 Close	the	taps.
•	 Remove	the	nuts	of	the	water	intake	hoses to clean the surfaces of the 
filters on the water intake valves with 
an appropriate brush.
•	 If	the	filters	are	very	dirty,	you	can	 pull them out by means of pliers and 
clean them.
•	 Take	out	the	filters	on	the	flat	 ends of the water intake hoses 
together with the gaskets and clean 
thoroughly under streaming water.
•	 Replace	the	gaskets	and	filters	 carefully and tighten the hose nuts 
by hand.
Draining any remaining...

EN25
•		 Pull	out	the	pump	outlet	hose	from	its housing.
•		 Place	a	large	container	at	the	end	of	 the hose. Drain the water off into the 
container by pulling out the plug at 
the end of the hose. If the amount 
of water to be drained off is greater 
than the volume of the container, 
replace the plug, pour the water out, 
then resume the draining process.
•		 After	draining	process	is	completed,	 replace the plug into the end of the 
hose and fit the hose back into its 
place.
If your product is not...

EN26
ProblemCause Explanation / Suggestion
Program	
cannot be 
started or 
selected. Machine	may	have	
switched to self 
protection mode due to 
an infrastructure problem 
(such	as	line	voltage,	
water	pressure,	etc.).
Reset	your	machine	by	pressing	“Start/Pause/
Cancel”	button	for	3	seconds.	(see,	Cancelling	
a	Program)
Water in the 
machine. There may be some water 
in your machine when you 
receive it. This is from the 
quality control process 
and is normal.
It is not harmful to your machine.
There...

EN27
The water 
being taken 
in is directly 
discharged.Improper position of the 
drain hose.
Connect the water draining hose as described 
in the operation manual.
No water can 
be seen in 
the machine 
during 
washing. This is not a problem. The 
water level is not visible 
from the outside of the 
machine.
The door is 
jammed. Water level might be 
above the lower level of 
the door.
Run	either	the	“Pump”	or	“Spin”	program.
Machine	might	be	heating	
up the water or it may be 
at the spinning cycle....

EN28
It continuously 
washes.
Remaining 
time does not 
count down.In the case of a paused 
countdown while taking in 
water:
Timer will not countdown 
until the machine is filled 
with the correct amount 
of water.
The machine will wait until there is a sufficient 
amount of water to avoid poor washing results 
due to lack of water. Then the timer will start to 
count down.
In the case of a paused 
countdown at the heating 
step:
Time will not count 
down until the selected 
temperature for the 
program...

EN29
Washing 
performance is 
poor:
Laundry turns 
gray - Using insufficient 
amount of detergent for a 
long time,
 - Washing at low 
temperatures for a long 
time,
 - Using insufficient 
amount of detergent for 
hard	waters	(soil	can	stick	
to	the	laundry),
 - Using excessive amount 
of	detergent	(detergent	
can	stick	to	the	laundry).  - Use the recommended amount of detergent 
appropriate for water hardness and the laundry.
 - Select the proper temperature for the laundry 
to be washed.
 - If the...

EN30
It does not 
rinse well.The amount, brand and 
storage conditions of the 
detergent used might not 
be appropriate.
Store detergent in a closed and dry place. Do 
not keep them under high temperatures.
Detergent might have 
been put in the wrong 
compartment. If detergent is put in the prewash compartment 
although prewash cycle is not selected, the 
machine can take this detergent during rinsing 
or softener step.
Machine	filter	may	be	
clogged. Check the filter.
Drain hose may be folded. Check the...