Home > Barco > Projector > Barco Projector Cineversum 80 User Manual

Barco Projector Cineversum 80 User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Barco Projector Cineversum 80 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 183 Barco manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							3. OVERVIEW USER’s CONTROLS
    3. OVERVIEW USER’S CONTROLS
    Overview
     Cine VERSUM Master
     Cine VERSUM 80
     Cine VERSUM 50
     Remote Control
     Remote Control operation
    3.1 Cine VERSUM Master
    Front View
    The front side of theCine VERSUM Master is provided with the following controls:
    Image 3-1
    Front side Cine VERSUM Master
    Controls function description
    Ref.FunctionDescription
    1Infra Red Reception LED indicatorLights up when a valid Infra Red signal from the Remote Control has
    been captured.
    2Infra Red ReceiverReception diode for the Infra Red signals sent by the Remote Control
    when a key is pressed.
    3Standby LEDBlinks when the Cine VERSUM Master has been powered down to
    Standby or Economy Standby mode.
    4Main power switch(see SWITCHING ON/OFF THE CINE VERSUM SYSTEM, page 15)
    5LCD DisplayThis display indicates the status of the Cine VERSUM Master and allows
    you to navigate through the different menus.
    6Selection and Confirmation dialThe knob allows to navigate through the different menus.
    Ta b l e 3 - 1
    3.2 Cine VERSUM 80
    To p V i e w
    The top side of the Cine VERSUM 80 is provided with the following controls:
    R5976490 CINE VERSUM SYSTEM 17012003
    7 
    						
    							3. OVERVIEW USER’s CONTROLS
    Image 3-2
    Cine VERSUM 80 controls
    Controls function description
    Ref.FunctionDescription
    1Infra Red ReceiverReception diode for the IR signals from the Remote Control. Allows
    switching On/Off (Standby) of the projector separately and controlling
    theCineVERSUMMaster.
    2Infra Red Reception LED indicatorLights up when a valid IR signal from the Remote Control has been
    captured.
    3Standby LEDLights up continuously: projector in the operation mode.
    Lights up repeatedly 2 times short, 1 time long: projector in the standby
    mode
    Blinks fast: projector in the cooling down mode after switching off
    (duration 1 min.).
    Lights up repeatedly 1 time long, 1 time short: projector has been started
    up in the cooling down mode, waiting for lamp ignition.
    4Main power switchButton pressed, switches the projector in the ’Standby’ mode. This mode
    is indicated by the standby LED which lights up repeatedly 2 times short,
    1 time long.
    Ta b l e 3 - 2
    3.3 Cine VERSUM 50
    Rear and Front view
    The only hardware control on the Cine VERSUM 50 is the Main Power Switch (1), located at the backside of the screen itself. This
    switch puts the Screen in the ’OFF’ or Standby position ’ON’. From the Standby position, the operation is controlled by the Cine
    VERSUM Master.
    The status of the Plasma screen is indicated by a blue LED (3), located at the bottom on the right of the screen. In the same corner
    an IR LED (2) is mounted .
    8
    R5976490 CINE VERSUM SYSTEM 17012003 
    						
    							3. OVERVIEW USER’s CONTROLS
    Image 3-3
    Cine VERSUM 50 controls
    Controls function description
    Ref.FunctionDescription
    1Main Power SwitchSwitches the Cine VERSUM 50 in the Standby mode. Operation mode is controlled
    by the Cine VERSUM Master.
    2Infra Red ReceiverReception diode for the IR signals from the Remote Control to control the Cine
    VERSUM Master.
    3Standby LEDIndicates the status of the Cine VERSUM 50, lights up in standby and operation
    mode.
    Ta b l e 3 - 3
    3.4 Remote Control
    To p s i d e
    The Infra Red Remote Control buttons support the following functionality:
    R5976490 CINE VERSUM SYSTEM 17012003
    9 
    						
    							3. OVERVIEW USER’s CONTROLS
    Image 3-4
    Remote Control
    Controls function description
    Ref.FunctionDescription
    1Address buttonTo match the Remote Control with the unit that you are addressing (number between
    0 and 9).
    2Standby buttonTo power up/down the Cine VERSUM Master and the displays in the link.
    3Digit buttonsAllows to directly select sources.
    4RC operation indicationLights up when a button on the remote control is pressed (Visual indication of remote
    control operation – Battery check).
    5TEXTPress to remove bar scale display when adjusting picture. Press button again for
    reactivation.
    6FREEZEPress to freeze the image
    7Picture controlsAllow to optimize the picture reproduction
    Ta b l e 3 - 4
    Stored sources
    The Cine VERSUM Master can be equipped with up to 8 digital and analog input modules. These modules are linked to your sources
    and can be selected with the touch of a button on the Remote Control.
    The table below allows you to note the stored source per input slot, digit button 1 to 8.
    Digit ButtonStored source
    1
    2
    3
    10R5976490 CINE VERSUM SYSTEM 17012003 
    						
    							3. OVERVIEW USER’s CONTROLS
    Digit ButtonStored source
    4
    5
    6
    7
    8
    3.5 Remote Control operation
    Overview
     General
     Battery Insertion in the Remote Control
     Visualization of commands
    3.5.1 General
    How to use
    The Remote Control allows you to control your Cine VERSUM Master, even when it is built into a cabinet. Indeed, the SL/XL cable
    allows for 2–way communication. This means you can point the Remote Control to a display unit and still change the settings of the
    Cine VERSUM Master.
    Image 3-5
    Master control via 2–way communication SL/XL cable
    Backlighting
    When a button on the remote control is pressed, backlight is activated automatically. That allows the user to operate the remote
    control in a dark room. Backlight is turned off automatically a few seconds after the last button activation.
    If backlight and RC operation indicator lights up too long or continuously, batteries need to be replaced.
    R5976490 CINE VERSUM SYSTEM 1701200311 
    						
    							3. OVERVIEW USER’s CONTROLS
    Factory address setting of the modules
    The factory address setting of the modules is as follows:
    ModuleIndividual AddressCommon Address
    Cine VERSUM 80address no common address
    Cine VERSUM 50address no common address
    Cine VERSUM Masteraddress common address 
    Common address: is a fixed address, stored in the module. The module will execute the commands sent by
    a Remote Control, programmed with thecommon address .
    3.5.2 Battery Insertion in the Remote Control
    Where to find the batteries
    The batteries are not placed in the remote control to avoid remote control operation in its package, resulting in a shorter battery life
    time.
    How to install the batteries
    1. Push the cover tab (A) with the fingernail a little backwards and pull upwards the cover top (B). (image 3-6)
    2. Slide the cover forwards to remove. (image 3-7)
    3. Push the battery body towards the spring and lift it up to remove. (image 3-8)
    4. Insert two AA size batteries, making sure the polarities match the + and – marks inside the battery compartment (image 3-8).
    5. Insert the lower tab of the battery cover in the gap at the bottom of the remote control, and press the cover until it clicks in place
    (image 3-8).
    Image 3-6
    Battery cover unlock
    Image 3-7
    Battery cover removal
    Image 3-8
    Battery removal
    12R5976490 CINE VERSUM SYSTEM 17012003 
    						
    							3. OVERVIEW USER’s CONTROLS
    How to reinstall the address
    By removing the batteries, the address in the Remote Control will be set to 0. In case the different modules are controlled separately
    (own address), the respective address of the module you desire to control has to be set. To reinstall an address, follow procedure
    below:
    1. Point the Remote Control to the module of which you want to know the address and press the address button (use a pencil).
    (image 3-9)
    On the screen appears a message box (image 3-10) indicating the address number. In the graphical display of the Cine VERSUM
    Master appears the same message (image 3-11).
    2. To adapt the address in the Remote Control, cover the IR transmitting diodes and press the address button once, followed within
    the 5 seconds by pressing the corresponding digit button, 1 to 8.
    Image 3-9Image 3-10
    Message address on-screen
    Image 3-11
    Message address display master
    3.5.3 Visualization of commands
    How the commands are visualized
    When a button on the Remote Control or the dial knob on the Cine VERSUM Master is pressed, the command is visualized on the
    screen of the plasma display or of the projector and also on the graphical display of the Cine VERSUM Master. This can take the
    form of a menu, a message or a bar scale. Below an illustration of each item:
    Image 3-12
    On-screen main menu
    Image 3-13
    Main menu on Master display
    R5976490 CINE VERSUM SYSTEM 1701200313 
    						
    							3. OVERVIEW USER’s CONTROLS
    Image 3-14
    On-screen message
    Image 3-15
    Message on Master display
    Image 3-16
    On-screen bar scale
    Image 3-17
    Bar scale on Master display
    14R5976490 CINE VERSUM SYSTEM 17012003 
    						
    							4. SWITCHING ON/OFF THE CINE VERSUM SYSTEM
    4. SWITCHING ON/OFF THE CINE VERSUM SYSTEM
    Overview
     Brief introduction
     Upon first startup
     Switching the system between OPERATION and STANDBY
     Switching the system between STANDBY and ECONOMIC Standby
     Switching the system OFF completely and BACK to Operation mode
     Turning ON the system from total OFF mode
    4.1 Brief introduction
    About the handled system in this manual
    The Cine VERSUM is a modular system that provides you the possibility to connect more than one display device to the Cine
    VERSUM Master.
    In this owner’s manual, we only discuss the most common case : one Master linked to one Projector. For info on the more complex
    systems, please review the installation manual.
    This is the chapter’s structure:
     Upon first startup
     Switching the system between OPERATION mode and STANDBY
     Switching the system between STANDBY and ECONOMIC STANDBY
     Switching the system OFF completely and BACK TO OPERATION mode.
    4.2 Upon first startup
    Required steps
    There are two steps upon first startup:
    1. Press the power switch (A) on the Cine VERSUM Master. (image 4-1)
    The Cine VERSUM Master goes from OFF to STANDBY, visualized by blinking of the standby indicator
    (B).
    2. Press the power switch (A) on the Cine VERSUM 80. (image 4-2)
    The Cine VERSUM 80 goes from OFF to STANDBY, visualized by blinking of the standby indicator
    (B).
    3. Select “Power up” in the menu on the Cine VERSUM Master, using the jog dial. (image 4-3, image 4-4)
    The Cine VERSUM Master and the Cine VERSUM 80 go from STANDBY to operation, visualized by lighting up of the proper
    standby indicator
    (B).
    Image 4-1
    Cine VERSUM Master
    R5976490 CINE VERSUM SYSTEM 1701200315 
    						
    							4. SWITCHING ON/OFF THE CINE VERSUM SYSTEM
    Image 4-2
    Cine VERSUM 80
    Image 4-3
    Cine VERSUM Master jog dial
    Image 4-4
    Power up selection
    4.3 Switching the system between OPERATION and STANDBY
    Overview
     From OPERATION mode to STANDBY mode
     From STANDBY mode to OPERATION mode
    4.3.1 From OPERATION mode to STANDBY mode
    Using the Jog dial on the Cine VERSUM Master
    1. Press the jog dial once to enter the main menu. (image 4-5)
    2. Rotate the jog dial until “Shut down” in the menu is pointed to. (image 4-6)
    3. Press jog dial to activate the Shutdown selection.
    The Cine VERSUM Master and the Cine VERSUM 80 go from OPERATION to STANDBY. During the power down process, a
    power down message appears on-screen and on the Master display. At the end, the Master displays the enter menu screen.
    (image 4-7, image 4-8)
    Image 4-5
    Main menu
    Image 4-6
    Shutdown selection
    Image 4-7
    Power down messageImage 4-8
    Enter menu screen
    16R5976490 CINE VERSUM SYSTEM 17012003 
    						
    All Barco manuals Comments (0)

    Related Manuals for Barco Projector Cineversum 80 User Manual