Barco Projector Cineversum 60 Quickstart Manual

8. Advanced Settings
How to shift the image ?
1. Push the cursor key↑or↓to highlightPosition. (menu 8-5)
2. PressENTERto select.
ThePositionmenu will be displayed. (menu 8-6)
3. Push the cursor key↑or↓to highlightHorizontal shift.
A slide bar will be displayed.
4. Use the cursor keys to shift the image horizontally.
When shifting to the left, the value will be negative.
When shifting to the right, the value will be positive.
The adjustment range can vary from - 255 to + 255. 0 is the nominal position....

8. Advanced Settings
Howtosizetheimage?
1. Push the cursor key↑or↓to highlightPosition. (menu 8-7)
2. PressENTERto select.
ThePositionmenu will be displayed. (menu 8-8)
3. Push the cursor key↑or↓to highlightHorizontal size.
A slide bar will be displayed.
4. Use the cursor keys to resize the image horizontally.
When the value is negative the image becomes smaller.
When the value is positive the image becomes wider.
The adjustment range can vary from - 255 to + 255. 0 is the nominal position.
Advanced...

8. Advanced Settings
How to shift the image ?
1. Push the cursor key↑or↓to highlightPosition. (menu 8-9)
2. PressENTERto select.
ThePositionmenu will be displayed. (menu 8-10)
3. Push the cursor key↑or↓to highlightVertical shift.
A slide bar will be displayed.
4. Use the cursor keys to shift the image vertically.
When shifting downwards, the value will be negative.
When shifting upwards, the value will be positive.
The adjustment range can vary from - 255 to + 255. 0 is the nominal position.
Advanced...

8. Advanced Settings
Howtosizetheimage?
1. Push the cursor key↑or↓to highlightPosition.(menu8-11)
2. PressENTERto select.
ThePositionmenu will be displayed. (menu 8-12)
3. Push the cursor key↑or↓to highlightVertical size.
A slide bar will be displayed.
4. Use the cursor keys to resize the image vertically.
When the value is negative the image becomes less high.
When the value is positive the image becomes higher.
The adjustment range can vary from - 255 to + 255. 0 is the nominal position.
Advanced...

8. Advanced Settings
Image 8-6
Blanking
A Top blanking
B Bottom blanking
C Left blanking
D Right blanking
Adjusting the blanking
1. Push the cursor key↑or↓to highlightBlanking. (menu 8-13)
2. PressENTERto select.
TheBlankingmenu will be displayed. (menu 8-14)
3. Push the cursor key↑or↓to highlight the desired blanking
4. PressENTERto start up the chosen blanking.
5. Use the cursor keys to adjust the blanking.
Advanced settings
Aspect Ratio
Position
PiP Configuration
Blanking
Input Balance
Back
Menu 8-13...

8. Advanced Settings
8.6.1 Introduction to Input Balance
Introduction: Unbalanced color signals
When transporting signals, there is always a risk of deterioration of the information contained in the signals.
In case of information contained in the amplitude of the signals which is the case of data color signals (R, G, B),image 8-7 , we are
quite sure that the amplitude of these color signals is subject to alterations.
An example of alteration may be a DC component added to the signal, in the form of a DC...

8. Advanced Settings
Black level setting : brightness
White level setting : contrast
The same absolute black and white level for the three colors allow the same reference for Brightness and contrast control of the
picture !
These two references also set the range in which the ADC will work for that particular source (this explains also why each input
balance setting is linked to a particular source and thus saved in the image file).
8.6.2 Adjusting the Input Balance for RGB signals
How can it be done ?...

8. Advanced Settings
4. PressENTERto select.
The black balance menu will be displayed. (menu 8-17)
5. Adjust the Brightness to a maximum value until there is just no green noise visible in the black areas.
6. Push the cursor key↑or↓to highlightBlack level red.
7. PressENTERto select.
8. Adjust with the cursor keys until there is no red noise visible in the black areas.
9. Repeat from step 6 but selectBlack level blueand adjust until no blue noise is visible in the black areas.
10.Set the brightness back...

8. Advanced Settings
5. PressENTERto select.
The black balance menu will be displayed. (menu 8-23)
6. Select Black level red and adjust the red balance with the cursor keys until the red noise becomes visible in the black areas.
7. Select now Black level blue and adjust the blue balance with the cursor keys until the blue noise becomes visible in black areas.
8. Increase the brightness until the black areas displays approximately 50% white noise.
9. Correct Red and Blue Black balance adjustment in such a...

8. Advanced Settings
56R5976763 CINEVERSUM 60/70 22042004