Home > Barco > Projector > Barco Projector Cineversum 110 User Manual

Barco Projector Cineversum 110 User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Barco Projector Cineversum 110 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 183 Barco manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							4. Getting Started
    ON
    OFFLamp 1
    Lamp 2
    Runtime(hrs)
    Lamp Status
    X(Lamp Take Over)
    X-30 (W ARNING)2X-30 (W ARNING)2X (ALERT)
    ON
    OFFLamp 1 +Lamp 2
    Runtime(hrs)
    Lamp Status
    X-30 (W ARNING)X (ALERT)
    A
    B
    Image 4-4
    Lamp runtime management
    A Single lamp mode
    B Dual lamp mode
    x Maximum lamp runtime
    In single mode, a lamp switch will be executed as far as the secondlamp has not reached its maximum runtime.
    WARNING:Using a lamp for more than x hours is dangerous as the lamp could explode.
    The lamp runtime reset as well as the lamp replacement can only be done by a Barco authorized technician.
    4.4 Switching to standby
    Howtoswitchtostandby?
    1. PressStandbyto switch the projector to standby.
    Switching to Standby. When the projector is running and you want to go to standby, press the standby key for
    2 seconds until the message ’Saving data, please wait’ is displayed. Do not press any longer on the standby
    key otherwise the projector will restart.
    4.5 Switching off
    How to switch off the projector?
    1. Press firstStandby.
    2. Let cool down the projector until the fans stop blowing, at least 15 min.
    3. Switch off the projector with the power switch.
    4.6 Temperature error DMD
    Overview
    When the temperature of one of the DMD is too low or too high theprojector will be switched automatically to standby. Before
    switching to standby, the following message appears for 3 seconds on the screen : ’DMD out of operating temperature range.
    Automatic shutdown is activated.’.
    R5976697 CINEVERSUM™ 110 12/05/2004
    37 
    						
    							4. Getting Started
    Ambient temperature range within the operating temperature range of the DMD is situated : +10°C and +40°C.
    4.7 Using the RCU
    Pointing to a reflective screen
    1. Point the front of the RCU to the reflective screen surface. (image 4-5)
    F
    1F
    2F
    3
    F
    4
    F
    5
    A
    DJ
    E
    X
    I
    T
    E
    N
    T
    E
    R
    P
    A
    U
    S
    E
    P
    H
    A
    S
    E T
    E
    X
    T
    S
    H
    A
    RP
    N
    T
    I
    N
    T
    C
    O
    L
    O
    R
    B
    R
    I
    G
    H
    T
    N
    C
    O
    N
    T
    R
    T
    R
    E
    B
    L
    EB
    A
    L
    A
    N
    C
    E
    B
    A
    S
    S
    V
    OL9
    0
    7856
    3
    4
    12
    IR Sensor (C)
    Screen (B) Remote Control (A)
    Image 4-5
    Pointing RCU to the screen
    A Remote control
    BScreen
    C IR sensor
    When using the remote control, make sure you are within the effective operating distance.
    The operating distance may be up to 15 m (50ft).
    The remote control unit will not function properly if strong light strikes the sensor window or if there are
    obstacles between the remote control and the IR sensor.
    Hardwired Remote input
    1. Plug one end of the remote cable in the connector on the bottom of the RCU. (image 4-6)
    2. Plug the other end in the connector in the front panel of the projector labelled RC.
    Specifications of the RC input
    -U
    in=9V
    -I
    max=80mA
    • Internal IR receivers can be disabled:
    omono jack : on plug in of the jack
    ostereo jack : on plug in or using an external switch bringing the right channel (B) to ground level. (image 4-7)
    Image 4-6
    Hardwired remote control
    38R5976697 CINEVERSUM™ 110 12/05/2004 
    						
    							4. Getting Started
    1
    2
    ABC
    D
    2
    3
    1
    Image 4-7
    Stereo jack pin configuration
    A tip: Left channel
    B ring: right channel
    C screen: common (GND)
    Dexternalswitch
    1Stereojack
    2 Mono jack
    The Remote connection uses a standard two wire cable terminated on each end with a 3.5 mm male
    (mono/stereo) phone jack.
    This cable is not delivered but is available in most electronic or audio shops.
    Directly to one of the IR sensors
    1. When using the wireless remote control, make sure you are within the effective operating distance (30m, 100ft in a straight line).
    The remote control unit will not function properly if strong light strikes the sensor window or if there are obstacles between the
    remote control unit and the projector IR sensor. (image 4-8)
    F
    1F
    2F
    3F
    4F
    5
    A
    DJE
    X
    I
    T
    E
    NT
    ER
    P
    AU
    SE
    P
    HA
    SE T
    EX
    TS
    HA
    RP
    NT
    IN
    TC
    OL
    ORB
    RI
    GH
    TNC
    ON
    TRT
    RE
    BL
    EB
    AL
    AN
    CEB
    AS
    SV
    OL 9
    0
    78
    56
    3
    4
    12
    45°45°
    F
    1F
    2F
    3F
    4F
    5
    A
    DJE
    XI
    T
    E
    NT
    ER
    P
    AU
    SE
    P
    HA
    SE T
    E
    X
    TS
    HA
    RP
    NT
    IN
    TC
    OL
    ORB
    RI
    GH
    TNC
    ON
    TRT
    RE
    BL
    EB
    AL
    AN
    CEB
    AS
    SV
    OL 9
    0
    78
    56
    3
    4
    12
    IR Sensor on Front (A)
    IR Sensor on Top (B)
    F1F2F3F4F5
    AD
    JEXIT
    ENTER
    PAUSE
    PHASE TEXTSHARPNTINTCOLORBRIGHTNCONTRTREBLEBALANCEBASS
    VOL 90
    78
    56
    34
    12
    IR Sensor (C)
    Image 4-8
    Remote control to IR sensor
    A IR sensor on front
    B IR sensor on top
    C IR sensor
    4.8 Projector address
    Overview
    • Address setting
    • Displaying and Programming addresses into the RCU
    4.8.1 Address setting
    Projector address
    Address installed in the projector to be individually controlled.
    R5976697 CINEVERSUM™ 110 12/05/200439 
    						
    							4. Getting Started
    Common address
    Default address. Projector will always execute the command coming from a RCU programmed with that common
    address.
    Why a projector address ?
    As more than one projector can be installed in a room, the separate projector should be separately addressable with an RCU or
    computer. Therefor each projector has its own address.
    Set up an individual Projector Address.
    The set up of a projector address can be done via the software.
    Projector controlling.
    Every projector requires an individual address between 0 and 255 which can be set in theInstallationmenu.
    Whentheaddressisset,theprojectorcanbecontrolledby:
    • RCU for addresses between 0 and 9.
    • computer, e.g. IBM PC (or compatible), Apple MAC, etc. for addresses between 0 and 255.
    A projector will respond to a RCU set to the common address ’0’ regardless of what address is set in the projector itself (common
    address of projector should also be “0” ).
    The RCU is default programmedwith address 0 , ’common address’.
    If it is necessary to control a specific projector, then enter the projector address into the RCU (only when that
    address is between 0 and 9). The projector with the corresponding address will listen to that specific RCU.
    Some projectors may operate in domestic environments where other equipments may listen to the common
    address “0” , therefore the common address can also be set to “1”.
    4.8.2 Displaying and Programming addresses into the RCU
    Displaying the Projector Address on the Screen.
    1. Press theAddresskey (recessed key on the RCU) with a pencil.
    The projector’s address will be displayed in a ’Text box’
    To continue using the RCU with that specific address, it is necessary to enter the same address with the
    digit buttons (address between 0 and 9) within 5 seconds after pushing the address key. For example : if the
    Address key displays projector address 003, then press 3 digit button on the RCU to set the RCU’s address
    to match the projector’s address. Do not press 0–0–3 . This will address the remote control to ’0’ and control
    all projectors in the room. If the address is not entered within 5 seconds, the RCU returns to its default address
    (zero address) and controls then all projectors in the room.
    Address 0 (or 1) should always allow communication with the projector since it is a common address.
    4.9 Controlling the projector
    Input Selection
    Key in the corresponding slot number with the digit keys on the RCU. The selected source will be displayed.
    Picture Controls
    When an image control is pressed, a text box with a bar scale, icon and function name of the control, e.g. ’brightness...’ appears
    on the screen (only ifTextboxin theDisplay Setupmenu is ON). The length of the bar scale and the value of the numeric indication
    indicate the current memorized setting for this source. The bar scale changes as the arrows on the RCU are pressed or the + or -
    buttons on the local keypad.
    The picture settings are saved in the image file.
    40
    R5976697 CINEVERSUM™ 110 12/05/2004 
    						
    							4. Getting Started
    Contrast
    20
    0
    100
    Image 4-9
    BrightnessUse the + button for a higher brightness.
    Use the - button for a lower brightness.
    ContrastUse the + button for a higher contrast.
    Use the - button for lower contrast.
    ColorUse the + button for richer colors.
    Use the - button for lighter colors.
    Tint (Hue)Tint is only active for Video and S-Video when using the NTSC 4.43 or NTSC 3.58 system.
    Use the + button
    Use the - button.
    SharpnessUse the + button for a sharper picture.
    Use the - button for a softer picture.
    PhaseUse the + or - button to adjust the phase.
    GammaUse the + button for a higher gamma
    Use the - button for a lower gamma
    FreezePressFreezeto freeze the displayed image.
    The Pause Key
    When the Pause key is pressed, the image projection is stopped, the image turns black.
    To restart the image projection:
    •PressPAUSEkey
    4.10 Quick lens adjustment
    Overview
    • Lens Adjustment via Menu Bar
    • Direct Lens Adjustment (RCU)
    4.10.1 Lens Adjustment via Menu Bar
    How to enter the adjustment menu.
    1. Press theMENUbutton (A) on the Remote Control.
    The menu bar (1) appears on top of the image. (image 4-10)
    2. Press→(A1) on adjust button to select menu itemInstallation.
    A text box appears with the first itemLens adjustmentselected (reversed text)
    3. PressENTERbutton (B) to activate the lens adjustment menu (2).
    The lens adjustment menu appears on the screen, requesting for ZOOM/FOCUS alignment.
    4. PressENTERbutton (B) to toggle between ZOOM/FOCUS and Vert. Hor. SHIFT menu (2).
    Note:For the alignment, a lens adjustment test pattern can be activated: toggle button (C) to activate or deactivate the lens
    adjustment test pattern (3).
    5. Press the corresponding arrows (A1) or (A2) on the adjust button, as indicated in front of the menu items, for alignment.
    6. Press control button (D) to leave the lens adjustment menu.
    R5976697 CINEVERSUM™ 110 12/05/2004
    41 
    						
    							4. Getting Started
    A2
    D
    A
    A1
    1
    2
    ...... Installation ......Lens adjustment
    Projector address
    ......
    Lens adjustment
    Use 
    ↑ and ↓ for zoom
    Use ← and → for focus
    Press  for SHIFT mode
    Press  or 
    for test pattern
    Lens adjustment
    Use 
    ↑ and ↓ for vertical shift
    Use ← and → for horizontal shift
    Press  for ZOOM/FOCUS
    Press  or 
    for test pattern
    B
    C
    3
    Lens adjustment
    Use ↑ and ↓ for zoom
    Use ← and → for focus
    Press  for SHIFT mode
    Press  or 
    for test pattern
    Lens adjustment
    Use ↑ and ↓ for verti cal shi ft
    Use ← and → for horizontal shift
    Press  for ZOOM/FOC US
    Press  or 
    for test pattern
    Image 4-10
    Lens adjustment via menu
    4.10.2 Direct Lens Adjustment (RCU)
    Lens adjustment button on the Remote Control
    On the Remote Control three buttons with double action are provided, allowing direct alignment for lens ZOOM, FOCUS and VER-
    TICAL SHIFT (For Horizontal Shift, see the first two procedures).
    1. PressLENS ZOOMbutton [-] or [+] (A) for correct image size on the screen.
    2. PressLENS FOCUSbutton [-] or [+] (C) for an overall focus of the image.
    3. PressLENS SHIFTbutton↑or↓(B) for correct vertical position of the image on the screen. (image 4-11)
    C
    A
    B
    Image 4-11
    Lens adjustment with RCU
    4.11 Digital Zoom
    What can be done ?
    The Digital Zoom key on the RCU allows to zoom in or out on one particular part of the image.
    Digital zoom cannot be performed on a logo.
    How to zoom ?
    1. Press←or→on theDigital Zoomkey on the remote control to zoom the center of the image.
    2. Use the↑,↓,→or←to pan the image. (image 4-12)
    3. PressENTERto confirm.
    Note:While in the digital zoom function, useBACKto return.
    42
    R5976697 CINEVERSUM™ 110 12/05/2004 
    						
    							4. Getting Started
    AB
    CD
    Image 4-12
    Digital zoom
    A Normal image
    B Digital zoom out
    C Digital zoom in
    D Panning of the zoomed image
    To return to the normal image, press MENU, go toTools, selectPiP selectand checkFull screen.
    R5976697 CINEVERSUM™ 110 12/05/200443 
    						
    							4. Getting Started
    44R5976697 CINEVERSUM™ 110 12/05/2004 
    						
    							5. Getting used with the Menu structure
    5. GETTING USED WITH THE MENU STRUCTURE
    5.1 How to start up the menus
    PC like menu structure
    The CineVERSUM™ 110 has a build in “PC like” menu bar which allows easy access to different parameters for setting up the
    projector.
    How to activate
    1. PressMENUon the RCU.
    The menu bar will be displayed on the screen.
    Menu items which are greyed out are not accessible for the current displayed source.
    5.2 Using the menu
    Menu Layout
    The existence of a submenu is indicated by a white arrow, e.g.Settingshas a submenu.
    E.g.Brightnessis an item of theImagemenu and has no submenu.
    Three suspension points indicate that the menu item hides a dialog box or a text box.
    Image 5-1
    The menus inserted in this manual are always full menus: all the items are visible.
    Greyed out menus or items are not available for the current selected source or current software version.
    How to pull down a menu ?
    1. Use↓to pull down a menu.
    R5976697 CINEVERSUM™ 110 12/05/2004
    45 
    						
    							5. Getting used with the Menu structure
    How to pull down a submenu ?
    1. Use→to pull down a submenu.
    How to exit the submenu ?
    1. PressBACKto exit a submenu.
    Press MENU to exit the menu
    5.3 Using the Dialog boxes
    How to use the dialog boxes ?
    Some parameters are modified by means of a dialog box, where selections can be made and/or values can be entered.
    The values can be entered in several ways:
    Entering numeric values using the numeric keys on the remote control
    1. PressENTERto activate the input field. (image 5-2)
    2. Key in the desired value.
    Projector addresses
    Projector address
    Common RC5 address5
    1
    Image 5-2
    Entering numeric values using the arrow keys on the remote control
    1. PressENTERto activate the input field.
    2. Press←or→to select the digit to be changed. (image 5-3)
    3. Press↓or↑to increase or decrease the value.
    Projector addresses
    Projector address
    Common RC5 address
    1005
    Image 5-3
    Entering numeric values using the arrow keys on the local keypad
    1. PressENTERto activate the input field.
    2. Press←or→to select the digit to be changed.
    3. Press↓or↑to increase or decrease the value.
    To confirm the changes always press ENTER.
    Use↓or↑to browse between the different fields.
    46R5976697 CINEVERSUM™ 110 12/05/2004 
    						
    All Barco manuals Comments (0)

    Related Manuals for Barco Projector Cineversum 110 User Manual