ATT 3800hgvb Manual

Connect the Computer to the Gateway
9
USB to PC Connection
1.Connect the provided AC power adapter from the 3700HGV-B’s POWER port to an electrical outlet. After 
the 3700HGV-B has completed  its start up process, the 
POWER light on the front of the 3700HGV-B 
should be green.
2.Connect the provided blue USB cable from the 3700HGV-B’s USB-PC port to the USB por t on the 
computer.
3.If the VDSL signal is carried over the phone line , connect the provided gray phone cable from the 
3700HGV-Bs 
PHONE...

Connect the Computer to the Gateway
10
Install the 2Wire Gateway USB Driver - Macintosh 
Note: The 2Wire gateway suppor ts USB for Macintosh OS 8.6, 9.2, 10.1.4, 10.1.5, 10.2.0, 
10.2.1 to 10.2.6, 10.3.3 to 10.3.9, 10.4.0, and 10.4.1.
Before making the USB connection to the gateway, y ou must install the 2Wire gateway USB driver on the 
computer. The following instructions are for USB  installation on Macintosh computers running OS 10.2.
1.With the computer powered on and the 2Wire Setup Wi zard CD in...

11
Connect the Broadband Interface
Now that you have completed the Power and LAN connections, it is time to connect to the broadband 
interface. There are two connection methods available:

 VDSL over Coax
If the 3700HGV-B is receiving the VSDL signal via RJ-11,  that step was completed in the previous chapter. If 
the 3700HGV-B is receiving the VSDL signal  via CoAX, refer to the following section.
Connecting to VDSL via CoAX
Figure 3. Inside Wiring Diagram
NIDLine 1 
(TDM)
from NID
RG STB
STB
VDSL...

12
Connect to IPTV
Setting Up IPTV
While the 3700HGV-B supports MoCA directly connected to it, it will not be used by SBC during the 
Controlled Launch. Instead MoCA or HomePNA will be  terminated on an Ethernet over CoAX bridge (for 
example, a Scientific Atlanta device or a Motorola NIM 100), which connects to an Ethernet por t on the 
3700HGV-B .
Note: The NIM100 is independently powered, and should  be installed close to a power outlet. 
Refer to the manufacturer’s instructions that came with the...

13
Gateway User Interface
This chapter describes the 2Wire gateway user interface.
Note: 2Wire recommends that you use Internet Explorer 5.5 (or higher) or Netscape 6 
(or higher).
Gateway (System) Pages
Viewing Your System Summar y
The System Summar y page provides general informat ion and links to the gateway’s most commonly used 
features.
The Network at a Glance panel provides a summary of the System, Broadband Link, and Home Network 
states of your gateway.
 The System area of the Network at a...

Gateway User Interface
14
Setting a System Password
Setting a system password protects your gateway settings from being modified or changed by someone who 
has not been given permission to do so. After setting a  system password, you will be required to enter it 
whenever you attempt to access a gateway configurat ion page — for example, if you tr y to change the 
gateway’s broadband connection settings or upgrade the ga teway software. If a password has not been set, 
a reminder notice is displayed...

Gateway User Interface
15
Viewing System Details
The System Details page provides information about your gateway, any enhanced services you may have, 
and provides a link that you can use to restar t your system.
Broadband Link Pages
Viewing Your Broadband Link Summar y
The Broadband Link Summar y page provides general  information about the current status of your 
broadband link connection and your system configuration.
The Connection panel shows information about your gateway’s connection to your...

Gateway User Interface
16
 Connection Status. There are two ways you can check the current status of your gateway’s broadband 
connection: you can use the BROADBAND LINK indicator  light on the front of your gateway, or, if your 
computer is connected to the network, you c an view the user interface. Connection Speed
 Connection Speed shows the incoming and outgoing data rates of your DSL connection, measured in  kilobits per second (Kbps). Incoming is the speed of  data flowing from the Internet to...

Gateway User Interface
17
From Jeff M.:
Need to show Ethernet broadband example page.
The information displayed depends on the type of broadband ser vice you have and your gateway model.
Using Broadband Diagnostics
Diagnostics displays an itemized list of your broadband connection’s current status. Technical support 
representatives use this information to help  troubleshoot problems with your broadband connection.
To update the broadband link status, click 
REFESH.
To initiate a full test of your...

Gateway User Interface
18
Viewing Statistics
The View Broadband Link Statistics page shows statistics associated with the 2Wire gateway broadband 
link, including cumulative DSL statistics.
Note: This page is not available for Ethernet  broadband connections. When it is temporarily 
displayed in menu bars (immediately after changing  from a DSL configuration), it will not contain 
any information.