Asus S62f Service Guide

                                        Upgrade & Replacement 
 
4 - 4   
4. Turn the non-remo vable screw here 180 degrees  counter-clockwise to 
loosen the CPU.  
 
                             
 
5.  Squeeze the vacuum handling pump and  use it to lift the CPU away.   
   
Installing CPU 
The illustration below shows how to install CPU and the heat sink of the 
notebook. 
 
1. Squeeze the vacuum handling pump  and use it to install the CPU.  
     
 
2. Turn the non-removable screw here 180 degrees...

                                        Upgrade & Replacement 
 
4 - 5   
3. Install the CPU thermal module gent ly and connect the fan cable then 
secure 2 screws (M2.5*4L  (K)) to secure it. 
 
     
M2.5*4L 
 
 
4. Secure 4 screws (M2*3L (K)) by order.  
                                                           
 
1 
2 3 
4 
M2*3L 
5. Install the CPU door and secure 2  screws (M2.5*4L (K)) to secure it. 
 
M2.5*4L 
 
Install battery module 
1.  Install the battery module. Slide the  battery latch to...

                                        Upgrade & Replacement 
 
4 - 6   
Second Memor y Upgrade MEMORY 
 The S62F Series Notebook does not  have RAM onboard. There are two SO-
DIMM sockets for installing SO-DIMM RA M. It can upgrade the total memory 
size up to 1GB with a 512MB module on each socket.   
 
Upgrading Memory Module  
Remove battery module  
1. Unlock and hold the latch No (1). 
 
  
1 
 
2. Slide the battery lock (No.2) and pull the battery pack out. 
 
   
2 
   
 
 
3. Pull the battery...

                                        Upgrade & Replacement 
 
4 - 7   
Removing Memory module  MEMORY 
REMOVAL  
1. Remove 2 screws (M2.5*4L (K )), then remove the DIMM door. 
 
 
M2.5*4L 
 
2. Open the 2 latches asi de (No. 1, 2), which will pop  the memory module up to 
an angle of 30 °, then pull out the memory modul e in that angle (No. 3). 
 
 
1  
3 
 
 
Installing Memory Module 
 
1.  Insert the Memory module into the memory socket by an angle of 30 degree, 
and push down to latch the memory...

                                        Upgrade & Replacement 
 
4 - 8   
2. Install the DIMM door  and secure 2 screws (M2.5* 4L (K)) to secure it. 
 
 
M2.5*4L 
 
Install battery module 
 
3. Install the battery module. Slide the battery latch to close the battery lock. BATTERY  
  
INSTALLATION 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  

                                        Upgrade & Replacement 
 
4 - 9   
HDD Upgrade HDD 
 The S62F Series Notebook uses an industry-standar d 2½” HDD with IDE 
interface.  You can replace the HDD to  any capacity of your choice within our 
approval and prior test. 
 
Upgrading HDD 
 
Remove battery module  
 
1. Unlock and hold the latch No (1). 
 
  
1 
2. Slide the battery lock (No. 2) and pull the battery pack out. 
 
   
2 
   
 
 
3. Pull the battery pack out. 
 
 
   

                                        Upgrade & Replacement 
 
4 - 10   
Removing HDD Module HDD 
MODULE 
REMOVAL 
 
1.  Remove 3 screws (M2.5*4L (K )), then remove the HDD door.  
 
 
   
M2.5*4L 
     
 
2.  Lift the HDD module and then remove it. 
 
 
 
3.  Remove 4 screws [M3 * 4(L)]  to separate HDD from HDD housing.  
 
M3*4L 
 
 
 
 
 
 
 
  

                                        Upgrade & Replacement 
 
4 - 11   
 Installing new HDD module 
4.  Secure 4 screws [M3 * 4(L) ] to fix HDD into HDD housing. HDD  
 
INSTALLATION 
 
 
M3*4L 
 
 
5.  Insert the HDD module to connect the FPC connector until it’s installed 
properly.  
 
 
6.  Install the bottom case  and secure 3 screws (M2.5*4L(K)) to fix it.  
 
M2.5*4L 
     
 
Install battery module 
7.  Install the battery module. Slide the  battery latch to close the battery lock. BATTERY...

                                        Upgrade & Replacement 
 
4 - 12   
Wireless LAN Module WIRELESS 
The illustration below shows how to remove the Wireless LAN module.  LAN 
Replacing WLAN 
 
Remove battery module  WALN 1. Unlock and hold the latch No (1). 
 REMOVAL 
 
1 
 
 
2. Slide the battery lock (No. 2) and pull the battery pack out. 
 
2 
      
 
 
3. Pull the battery pack out. 
 
 
 
 
  

                                        Upgrade & Replacement 
 
4 - 13   
Removing WALN Module 
 
1.  Remove 1 piece of tape and  disconnect the MAIN & AUX antenna. ODD 
 REMOVAL 
    
 
2.  And open the two latches to pop the MINI PCI MODULE up then pull it out. 
 
 
 
 
Installing new WALN module WALN MODULE  INSTALLATION 3.  Install the MINI PCI module into t he socket by an angle of 30 degree, and 
push down to latch the MINI PCI module.