Asus Router RT_N13 User Manual Czech Version

							
1
Chapter 5: Installing the utilities                       RT-N1

7. You have connected to the wireless router. If you want to configure the Internet settings, click Setup. Click Finish to close the WPS Wizard.
Adding network devices using a USB flash drive
With the WPS utility, you can add devices to your network using a US� flash drive.
To add network devices using a USB flash drive:
1. In the WPS Wizard, click Save settings to a USB flash drive. 
						

							

RT-N1                       Chapter 5: Installing the utilities

2. Plug a US� flash drive into a US� port on your computer, and then select the drive from the dropdown list. When done, click Next to continue.
3. Remove the US� flash drive from this computer, and then plug to the computer that you want to add to the wireless network.
4. Locate the SetupWireless.exe from the USB drive, and double-click to run it. Click Yes to add this computer to the wireless network. 
						

							

Chapter 5: Installing the utilities                       RT-N1

5. Click OK to exit the Wireless Network Setup Wizard. 
						

							
4
RT-N1                         Chapter 6: Troubleshooting

6
Troubleshooting
This troubleshooting guide provides solutions to some common problems that you may encounter while installing or using the ASUS Wireless Router. These problems require simple troubleshooting that you can perform by yourself. Contact the ASUS Technical Support if you encounter problems not mentioned in this chapter.
ProblemAction
I cannot access a web browser for configuring the router.
1. Launch a web browser, then click Tools > Internet Options... 
2. Under Temporary Internet files, click Delete Cookies... and Delete Files...
The client cannot establish a wireless connection with the router.
Out of Range:
• Put the router closer to the wireless client.
• Try to change the channel settings.
Authentication:
• Use wired connection to connect to the router.
• Check the wireless security settings.
• Press the Restore button at the rear panel for more than five seconds.
Cannot find the router:
• Press the Restore button at the rear panel for more than five seconds.
• Check the setting in the wireless adapter such as SSID and encryption settings.
Troubleshooting 
						

							
5
Chapter 6: Troubleshooting                         RT-N1

ProblemAction
Cannot access the Internet via wireless LAN adapter• Move the router closer to the wireless client.
• Check whether the wireless adapter is connected to the correct wireless router.
• Check whether the wireless channel in use conforms to the channels available in your country/ area.
• Check the encryption settings.
• Check if the ADSL or Cable connection is correct.
• Retry using another Ethernet cable.
Internet is not accessible• Check the status indicators on the ADSL modem and the wireless router.
• Check if the WAN LED on the wireless router is ON. If the LED is not ON, change the cable and try again.
When ADSL Modem “Link” light is ON (not blinking), this means Internet Access is possible.
• Restart your computer.
• Refer to the Quick Start Guide of the wireless router and re-configure the settings.
• Check if the WAN LED on the wireless router is ON.
• Check the wireless encryption settings.
• Check if the computer can get the IP address (via both wired network and wireless network).
• Ensure that your web browser is configured to use the local LAN, and is not configured to use a proxy server.
If the ADSL “LINK” light blinks continuously or stays off, Internet access is not possible - the Router is unable to establish a connection with the ADSL network.
• Ensure that all your cables are all correctly connected .
• Disconnect the power cord from the ADSL or cable modem, wait a few minutes, then reconnect the cord.
• If the ADSL light continues to blink or stays OFF, contact your ADSL service provider. 
						

							
6RT-N1                         Chapter 6: Troubleshooting
ProblemAction
Network name or encryption keys are forgotten• Try setting up the wired connection and configuring the wireless encryption again.
 
• Press the Restore button at the rear panel of the wireless router for more than five seconds.
How to restore the system to its default settings• Press the Restore button at the rear panel of the wireless router for more than five seconds.
• Refer to the section Restoring to the default settings in Chapter 5 of this user manual.
The following are the factory default settings:
User Name: admin 
Password: admin
Enable DHCP: Yes (if WAN cable is plugged in)
IP address: 19.168.1.1
Domain Name: (Blank)
Subnet Mask: 55.55.55.0
DNS Server 1: 19.168.1.1
DNS Server 2: (Blank)
SSID: default 
						

							
7Appendices                               RT-N1
Notices
Federal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is subject\
 to the following two conditions: 
• This device may not cause harmful interference.
• This device must accept any interference received, including interference that    may cause undesired operation.
This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Prohibition of Co-location
This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter
Appendices 
						

							
8
RT-N1                               Appendices

Safety Information
To maintain compliance with FCC’s RF exposure guidelines, this equipment should be installed and operated with minimum distance 0cm between the radiator and 
your body. Use on the supplied antenna.
Declaration of Conformity for R&TTE directive 
1999/5/EC
Essential requirements – Article 
Protection requirements for health and safety – Article .1a
Testing for electric safety according to EN 60950-1 has been conducted. These are considered relevant and sufficient.
Protection requirements for electromagnetic compatibility – Article .1b
Testing for electromagnetic compatibility according to EN 01 489-1 and EN 01 489-17 has been conducted. These are considered relevant and sufficient.
Effective use of the radio spectrum – Article .
Testing for radio test suites according to EN 00 8-  has been conducted. These are considered relevant and sufficient.
CE Mark Warning
This is a Class B product, in a domestic environment, this product may c\
ause radio interference, in which case the user may be required to take adequate measures.
DGT 警語
經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、
加大功率或變更原設計之特性及功能。
低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即
停用，並改善至無干擾時方得繼續使用。
前項合法通信，指依電信法規定作業之無線電通信。
低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。 
						

							
9
Appendices                               RT-N1

GNU General Public License
Licensing information
This product includes copyrighted third-party software licensed under th\
e terms of the GNU General Public License. Please see The GNU General Public License for the exact terms and conditions of this license. We include a copy of the GPL with every CD shipped with our product. All future firmware updates will also be accompanied with their respective source code. Please visit our web s\
ite for updated information. Note that we do not offer direct support for the distribution.
GNU GENERAL PUBLIC LICENSE
Version , June 1991
Copyright (C) 1989, 1991 Free Software Foundation, Inc.
59 Temple Place, Suite 0, Boston, MA 0111-107 USA
Everyone is permitted to copy and distribute verbatim copies of this lic\
ense document, but changing it is not allowed.
Preamble
The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public License is inte\
nded to guarantee your freedom to share and change free software--to make sure the software is free for all its users. This General Public License applies to most of the Free Software Foundation’s software and to any other program whose authors commit to using it. (Some other Free Software Foundation software is co\
vered by the GNU Library General Public License instead.) You can apply it to your programs, too.
When we speak of free software, we are referring to freedom, not price. \
Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you \
wish), that you receive source code or can get it if you want it, that you can change th\
e software or use pieces of it in new free programs; and that you know you can do these things.
To protect your rights, we need to make restrictions that forbid anyone t\
o deny you these rights or to ask you to surrender the rights. These restrictions translate to certain responsibilities for you if you distribute copies of the soft\
ware, or if you modify it.
For example, if you distribute copies of such a program, whether gratis \
or for a fee, you must give the recipients all the rights that you have. You must make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights. 
						

							
40
RT-N1                               Appendices

We protect your rights with two steps: (1) copyright the software, and \
() offer you this license which gives you legal permission to copy, distribute and/or modify the software.
Also, for each author’s protection and ours, we want to make certain that everyone understands that there is no warranty for this free software. If the sof\
tware is modified by someone else and passed on, we want its recipients to know that what they have is not the original, so that any problems introduced by others\
 will not reflect on the original authors’ reputations.
Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program will individually\
 obtain patent licenses, in effect making the program proprietary. To prevent this, we have made it clear that any patent must be licensed for everyone’s free use or not licensed at all.
The precise terms and conditions for copying, distribution and modification follow.
Terms & conditions for copying, distribution, & modification
0. This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under the te\
rms of this General Public License. The “Program”, below, refers to any such program or work, and a “work based on the Program” means either the Progra\
m or any derivative work under copyright law: that is to say, a work containing the Program or a portion of it, either verbatim or with modifications and/or translated into another language. (Hereinafter, translation is included without limitation in the term “modification”.) Each licensee is addressed as “you ”.
 Activities other than copying, distribution and modification are not cov ered by this License; they are outside its scope. The act of running the Program is not restricted, and the output from the Program is covered only if its c\
ontents constitute a work based on the Program (independent of having been made by running the Program). Whether that is true depends on what the Program does.
1.  You may copy and distribute verbatim copies of the Program’s source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this Licens e and to the absence of any warranty; and give any other recipients of the Prog ram a copy of this License along with the Program.
 You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee.
. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program, and copy and distribute such