Apple macbook pro 17 inch User Manual

							MacBook Pro 17-inch (original, Core 2 Duo, 2.4/2.6GHz, 2008) Take Apart — Heatsink 141
Heatsink
Tools
This procedure requires the following tools: Black stick (nylon probe 922-5065) or other non-conductive nylon or plastic flat-blade tool
• 
Preliminary Steps
Before you begin, remove the following:
Batter
•  y
Top Cas
•  e
Logic Boar
•  d
Part Location 
						

							MacBook Pro 17-inch (original, Core 2 Duo, 2.4/2.6GHz, 2008) Take Apart — Heatsink 14 2
Procedure
Note: Some photo details below may differ slightly from the model of 17-inch MacBook Pro you 
are repairing; however, the procedure itself remains consistent for any of the models.If the fans will not be removed, cut the tape between the fans and the heatsink (as described 
1.  
in the Fans Chapter), then lift out the heatsink.  
When installing the heatsink, make sure that it fits over the pins, shown, and lays flat.  
2.  
Make sure to install new thermal grease as outlined in the 
3.  Logic Board chapter. 
						

							MacBook Pro 17-inch (original, Core 2 Duo, 2.4/2.6GHz, 2008) Take Apart — Bottom Case 14 3
Bottom Case
Tools
This procedure requires no tools.
Preliminary Steps
Before you begin, remove the following:Batter
•  y
Top Cas
•  e
AirPort Extreme Car
•  d
Hard Driv
•  e
Bluetoot
•  h
Infrared Boar
•  d
Optical Driv
•  e
Speaker
•  s
Left I/O Boar
•  d
Fan
•  s
Logic Boar
•  d
Heatsin
•  k
Display Assembl
•  y 
						

							MacBook Pro 17-inch (original, Core 2 Duo, 2.4/2.6GHz, 2008) Take Apart — Bottom Case 14 4
Part Location
Procedure
Note: If replacing the bottom case, use a razor knife to carefully lift and transfer the Serial 
Number and Ethernet ID labels to the replacement bottom case.
After the parts are removed in the preliminary steps, what’s left is the bottom case.. 
						

							MacBook Pro 17-inch (original, Core 2 Duo, 2.4/2.6GHz, 2008) Take Apart — Display Assembly 14 5
Display Assembly
Tools
This procedure requires the following tools: Torx T6 screwdriver (magnetized)
• 
Black stick (nylon probe 922-5065) or other non-conductive nylon or plastic flat-blade tool
• 
Preliminary Steps
Before you begin, remove the following:
Batter
•  y
Top Cas
•  e
Part Location 
						

							MacBook Pro 17-inch (original, Core 2 Duo, 2.4/2.6GHz, 2008) Take Apart — Display Assembly 14 6
Procedure
Note: Some photo details below may differ slightly from the model of 17-inch MacBook Pro you 
are repairing; however, the procedure itself remains consistent for any of the models.Disconnect two antenna connectors for the MacBook Pro (17-inch original and Early 2008) 
1.  
or three connectors for the MacBook Pro (17-inch Core 2 Duo and 2.4GHz) from the AirPort 
Extreme card. Lift straight up.  
Note: Take note of the order of the antenna connectors for reinstallation purposes.
Disconnect three cable connectors on the logic board—the camera and inverter connectors 
2.  
and the LVDS connector.
Remove the four clutch spring end cap screws, two each side.
3.  
						

							MacBook Pro 17-inch (original, Core 2 Duo, 2.4/2.6GHz, 2008) Take Apart — Display Assembly 14 7
Move the display straight up to a 90-degree angle and remove six clutch block screws, three 
4.  
on each side.
Important: Support the display from falling over before removing the last screw.
Lift the display straight up and off of the computer without catching wires.
5. 
Remove the clutch spring end caps from each side.  
6.   
						

							MacBook Pro 17-inch (original, Core 2 Duo, 2.4/2.6GHz, 2008) Take Apart — Display Assembly 14 8
Replacement Procedure
Before installing the display assembly, verify that all cables are routed out of the way.
1.  
Install the replacement display assembly, and reconnect all cables and antennas.
2.  
Make sure to capture the LVDS cable grounding loop with the screw., and that the cable is 
3. 
secure and lays flat.  
Verify that the EMI gasket is on the camera cable connector.  
4.   
						

							MacBook Pro 17-inch (original, Core 2 Duo, 2.4/2.6GHz, 2008) Take Apart — Display Assembly 14 9
Verify that the antenna cables lay flat within the channel along the edge of the speaker.
 
5. 
If not, use Kapton tape to secure, as shown.  
6.   
						

							MacBook Pro 17-inch (original, Core 2 Duo, 2.4/2.6GHz, 2008) Take Apart — Display Assembly 15 0
And verify that the cables for the antennas, and camera and inverter, route to the left of the 
7.  
pin and screw hole at the top right corner of the speaker.  
Reassemble and test the computer.
8.  
Testing the computer should include:
9. 
Testing that the display panel functions properly. 
• 
Use Apple System Profiler to check that the AirPort Extreme card is recognized, and test 
• 
that AirPort Extreme is working.
Check the camera function. 
• 
Check that the trackpad and keyboard function properly. 
• 
Operate the computer in a darkened room to check for keyboard backlight function.
•