Apple macbook pro 17 inch User Manual

							MacBook Pro 17-inch (original, Core 2 Duo, 2.4/2.6GHz, 2008) Take Apart — Speakers 101
If not, use Kapton tape to secure, as shown.
 
• 
And verify that the cables for the antennas, and camera and inverter, route to the left of the 
• 
pin and screw hole at the top right corner of the speaker.   
						

							MacBook Pro 17-inch (original, Core 2 Duo, 2.4/2.6GHz, 2008) Take Apart — Speakers 10 2
To remove the right speaker:
Once the logic board is removed, lift out the right speaker, guide its cable out of the channel 
1.  
above the battery well, and disconnect its connector from the left I/O board.  
  
						

							MacBook Pro 17-inch (original, Core 2 Duo, 2.4/2.6GHz, 2008) Take Apart — Left I/O Board 10 3
Left I/O Board
Tools
This procedure requires the following tools: Torx T6 screwdriver (magnetized)
• 
#0 Phillips screwdriver (magnetized)
• 
Black stick (nylon probe 922-5065) or other non-conductive nylon or plastic flat-blade tool
• 
Preliminary Steps
Before you begin, remove the following:
Batter
•  y
Top Cas
•  e
AirPort Extreme Car
•  d
Left Speake
•  r
Part Location 
						

							MacBook Pro 17-inch (original, Core 2 Duo, 2.4/2.6GHz, 2008) Take Apart — Left I/O Board 10 4
Procedure
Note: Some photo details below may differ slightly from the model of 17-inch MacBook Pro you 
are repairing; however, the procedure itself remains consistent for any of the models.Disconnect the hard drive and ExpressCard flex cables, as shown below.
1.  
 
Disconnect the left I/O cable and right speaker cable.
2.   
						

							MacBook Pro 17-inch (original, Core 2 Duo, 2.4/2.6GHz, 2008) Take Apart — Left I/O Board 10 5
Remove the four Torx T6 screws.
3. 
 
Lift slightly and slide the left I/O board assembly away from the port openings to remove.
4.   
						

							MacBook Pro 17-inch (original, Core 2 Duo, 2.4/2.6GHz, 2008) Take Apart — Left I/O Board 10 6
The ExpressCard cage assembly is attached to the left I/O board. Peel back the Mylar that 
5. 
covers the top two screws and remove all four screws.
(b) The MacBook Pro (17-inch 2.4GHz and Early 2008 models) will have a black Mylar film 
underneath the screws (unlike Kapton below), so no need to remove the film. Just remove 
the four pocket screws. 
						

							MacBook Pro 17-inch (original, Core 2 Duo, 2.4/2.6GHz, 2008) Take Apart — Left I/O Board 10 7
Lift off the card cage.
6.  
 
(b) The MacBook Pro (17-inch 2.4GHz) ExpressCard cage will look like the photo below.
(c) The MacBook Pro (17-inch Early 2008) ExpressCard cage will also have a piece of copper 
EMI shielding on the card cage where the Kapton tape is shown below. 
						

							MacBook Pro 17-inch (original, Core 2 Duo, 2.4/2.6GHz, 2008) Take Apart — Left I/O Board 10 8
Replacement Notes:
7.    
Transfer the any EMI gaskets from the former left I/O board.
• 
Install the flex cable in the orientation shown.  
• 
When the board is in place and the ports are seated, hold the power adapter port tightly 
•  
						

							MacBook Pro 17-inch (original, Core 2 Duo, 2.4/2.6GHz, 2008) Take Apart — Left I/O Board 10 9
against the port opening while installing screws.
 
After securing the board, exercise the ExpressCard slot door to verify clearance.
•  
						

							MacBook Pro 17-inch (original, Core 2 Duo, 2.4/2.6GHz, 2008) Take Apart — ExpressCard Cage 11 0
ExpressCard Cage
Tools
This procedure requires the following tools: #0 Phillips screwdriver (magnetized)
• 
Preliminary Steps
Before you begin, remove the following:
Batter
•  y
Top Cas
•  e
AirPort Extreme Car
•  d
Left Speake
•  r
Left I/O Boar
•  d
Part Location
Procedure
See the Left I/O Boar d chapter for removal of the ExpressCard cage.