Apple mac pro early 2009 User Manual
Here you can view all the pages of manual Apple mac pro early 2009 User Manual. The Apple manuals for Personal Computer are available online for free. You can easily download all the documents as PDF.
Page 191
Mac Pro (Early 2009) Take Apart — Front Panel Board 191 2010-09-27 Removal 1 Disconnect power button cable from front panel board. 2 Remove 5 screws. 3 Remove board from enclosure.
Page 192
Mac Pro (Early 2009) Take Apart — Power Button 192 2010-09-27 First Steps Open computer, lay it down with access side facing up, and remove: • Hard drive and drive carrier in drive bay 1 • Graphics card in slot 1 • PCIe fan • Processor tray • Processor cage • Front-panel-board- to-backplane-board cable Tools • ESD wrist strap • Jeweler’s flatblade screwdriver Power Button
Page 193
Mac Pro (Early 2009) Take Apart — Power Button 193 2010-09-27 Removal 1 Disconnect power button cable from front panel board. 2 Lay computer so that front panel is facing down. 3 Remove black cap. 4 Using jeweler’s flatblade screwdriver, pry up metal C-ring. 5 Remove power button board. 6 Remove metal activation ring. 7 Remove power button.
Page 194
Mac Pro (Early 2009) Take Apart — Optical Drive Cable Harness 194 2010-09-27 First Steps Open computer, lay it down with access side facing up, and remove: • All hard drives and drive carriers • Optical drive carrier and optical drives • PCIe fan • All PCI Express cards • Processor tray • Processor cage • Front-panel-board- to-backplane-board cable • Backplane board Tools • ESD wrist strap Optical Drive Cable Harness
Page 195
Mac Pro (Early 2009) Take Apart — Optical Drive Cable Harness 195 2010-09-27 Removal 1 Insert backplane- board connectors on cable harness through opening in media shelf. 2 Remove cable harness from enclosure.
Page 196
Mac Pro (Early 2009) Take Apart — Bluetooth Antenna Board with Cable 196 2010-09-27 First Steps Open computer, lay it down with access side facing up, and remove: • All hard drives and drive carriers • Optical drive carrier and optical drives • PCIe fan • All PCI Express cards • Processor tray • Processor cage • Front-panel-board- to-backplane-board cable • Backplane board Tools • ESD wrist strap • Jeweler’s Phillips screwdriver • Long-handled, magnetized T8 torx screwdriver Bluetooth Antenna...
Page 197
Mac Pro (Early 2009) Take Apart — Bluetooth Antenna Board with Cable 197 2010-09-27 Removal 1 Remove antenna board mounting screw. 2 Remove tape holding Bluetooth cable to enclosure. Note: If a metal loop is attached to Bluetooth antenna cable, remove enclosure screw that secures loop. See Reassembly steps 3-6. 3 Gently grasp Bluetooth antenna board and pull it out of its mounting. 4 Remove antenna board and cable from enclosure.
Page 198
Mac Pro (Early 2009) Take Apart — Bluetooth Antenna Board with Cable 198 2010-09-27 Reassembly 1 Insert replacement antenna board at an angle into its mounting. Then straighten out board and insert fully. 2 Replace antenna board mounting screw.
Page 199
Mac Pro (Early 2009) Take Apart — Bluetooth Antenna Board with Cable 199 2010-09-27 Note: A metal grounding loop is attached to the replacement antenna board cable. Do the following to ground the loop to the enclosure: 3 Using a T8 torx screwdriver, remove the enclosure screw indicated. 4 Place washer (included with replacement antenna board) face up over screw hole. 5 Place grounding loop over washer. 6 Reinstall enclosure screw. 7 Replace tape that secures cable to enclosure. If you...
Page 200
© 2009 Apple Inc. All rights reserved. Apple Technician Guide Views Mac Pro (Early 2009)