Apple led cinema display 27inch User Manual
Here you can view all the pages of manual Apple led cinema display 27inch User Manual. The Apple manuals for Display are available online for free. You can easily download all the documents as PDF.
Page 91
LED Cinema Display (27-inch) Take Apart — Logic Board 91 2010-11-18 Logic Board Connectors 1. DC power 2. LCD function 3. fan (4-pin) 4. ambient temp sensor (3-pin) 5. camera (7-pin) 6. microphone (3-pin; translucent white) 7. subwoofer (2-pin) 8. left speaker (5-pin) 9. right speaker (4-pin) 10. USB uplink (metal; part of all-in-one cable) 11. LED backlight driver (part of LCD panel)
Page 92
LED Cinema Display (27-inch) Take Apart — Logic Board 92 2010-11-18 EDID Reset Tool After replacing the LCD panel or the logic board in an LED Cinema Display (27-inch), run the EDID Reset Tool to reset the Extended Display Identification Data (EDID). If this tool is not used when the LCD panel and/or logic board are replaced, software features such as the brightness control may not be available. 1. Download the EDID Reset Tool from Service Source, by navigating the Product Browser to “Displays” and...
Page 93
LED Cinema Display (27-inch) Take Apart — Left Speaker 93 2010-11-18 First Steps Remove: • Glass Panel • LCD Panel Tools • ESD wrist strap • Torx T10 screwdriver Left Speaker
Page 94
LED Cinema Display (27-inch) Take Apart — Left Speaker 94 2010-11-18 Removal 1 Remove T10 screws: (2) 922-9236 2 Note cable routing and tape placement along rear housing. 3 Disconnect 5-pin speaker cable from logic board. 4 Remove speaker from rear housing. Reassembly Note: Insert tab into guide in rear housing. Reassembly Note: For easier access to reconnect cables, unscrew and flip over logic board.
Page 95
LED Cinema Display (27-inch) Take Apart — Right Speaker 95 2010-11-18 First Steps Remove: • Glass Panel • LCD Panel • Logic Board Tools • ESD wrist strap • Torx T10 screwdriver Right Speaker
Page 96
LED Cinema Display (27-inch) Take Apart — Right Speaker 96 2010-11-18 Removal 1 Remove T10 screws: (2) 922-9236 2 Note cable routing and tape on rear housing. 3 Remove speaker from rear housing. Reassembly Notes: • Insert tab into guide in rear housing. • Make sure USB uplink cable rests against foam gasket on top left of speaker, to avoid vibration noise.
Page 97
LED Cinema Display (27-inch) Take Apart — Subwoofer 97 2010-11-18 First Steps Remove: • Glass Panel • LCD Panel Tools • ESD wrist strap • Torx T10 screwdriver Subwoofer
Page 98
LED Cinema Display (27-inch) Take Apart — Subwoofer 98 2010-11-18 Removal 1 Remove T10 screws: (4) 922-9722 2 Disconnect 2-pin subwoofer cable from logic board Reassembly Note: For easier access to reconnect cables, unscrew and flip over logic board. 3 Remove subwoofer from rear housing.
Page 99
LED Cinema Display (27-inch) Take Apart — All-in-One Cable 99 2010-11-18 First Steps Remove: • Glass Panel • LCD Panel • Logic Board • Subwoofer Tools • ESD wrist strap • Torx T10 screwdriver All-in-One Cable
Page 100
LED Cinema Display (27-inch) Take Apart — All-in-One Cable 100 2010-11-18 Removal 1 Remove T10 screws: (1) 922-8685, machine, top left (also secures gasket and AC inlet) (2) 922-9351 Loosen 2 other T10 screws on AC inlet. 2 Remove round metal bracket. Reassembly Note: Bracket tucks underneath metal tab of AC inlet. 3 Note cable routing and tape securing the USB uplink, DisplayPort, and power cables inside rear housing. 4 Peel back tape securing cables to rear housing, and “H”...