Apple led cinema display 24inch User Manual
Have a look at the manual Apple led cinema display 24inch User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 195 Apple manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
LED Cinema Display (24-inch) Take Apart — Mechanism 81 2010-11-25 First Steps Remove: • G lass Panel • L CD Panel • Sub woofer • S tand Tools • ESD wrist strap • T orx T10 screwdriver Mechanism
LED Cinema Display (24-inch) Take Apart — Mechanism 82 2010-11-25 Removal 1 Remove 4 screws: T10, 922-8682 2 Peel EMI mesh tape off the rear housing. Replacement Reassembly is an exact reversal of the steps. Note: Install mechanism onto the rear housing with the serial number showing at the top. Replacement Note: If replacing mechanism, transfer serial number sticker to new part.
LED Cinema Display (24-inch) Take Apart — Rear Housing 83 2010-11-25 First Steps Remove: • G lass Panel • L CD Panel • L ogic Board • P ower Supply • F an • C amera • Sub woofer • A C Inlet • A ll-In-One Cable • S tand • M echanism Rear Housing With all the modules removed, you are left with the rear housing assembly. A new rear housing includes the following parts, which are not available separately: • micr ophone cable • A C inlet A new rear housing also includes the following parts, which can be ordered separately: • lef t speaker • r ight speaker
LED Cinema Display (24-inch) Take Apart — Rear Housing 84 2010-11-25 Camera Thermal Paste Transfer camera from old rear housing to new rear housing and reuse thermal paste from old rear housing. Use a black stick to remove and reapply thermal paste to camera (areas circled). Note: A syringe of thermal paste is available as needed, Apple part# 922- 9625, good for 5 applications.
© 2008-2010 Apple Inc. All rights reserved. Apple Technician Guide Additional Procedures LED Cinema Display (24-inch)
LED Cinema Display (24-inch) Additional Procedures — VESA Mount 86 2010-11-25 First Steps No preliminary steps are required. Tools • ESD wrist strap • T orx T10 screwdriver • A ccess card to lock/ unlock the stand (Apple part #922-7172) VESA Mount
LED Cinema Display (24-inch) Additional Procedures — VESA Mount 87 2010-11-25 Removal 1 Place unit face down on a table so that base of stand extends over table edge. 2 Press stand down and insert access card into slot between top of stand and rear housing. 3 Insert access card as far as it will go, and press stand down until you hear a click — the audible cue that indicates stand is locked into place. 4 Remove access card.
LED Cinema Display (24-inch) Additional Procedures — VESA Mount 88 2010-11-25 5 Remove 8 screws: T10, 922-8749 6 Remove stand from clutch mechanism. Reassembly 1 Place unit face down on a table. Align pin on mechanism to central hole in stand. 2 Replace 8 T10 screws. 3 Place unit so that base of stand extends over table edge. Press stand down and insert access card into slot between top of stand and rear housing. 4 Insert access card as far as it will go. Gently lift stand approximately two inches to unlock mechanism, and then remove access card. Mechanism should now be unlocked. 5 Stand unit upright.
LED Cinema Display (24-inch) Additional Procedures — Retrieving Mechanism 89 2010-11-25 Overview Without a stand or VESA mount installed, the mechanism can retract inside the computer if an access card trips the latch that locks the mechanism. In the rare event that retrieving the mechanism is necessary, follow this procedure. Tools • Access card (Apple part #922-7172) • R etrieval tool (Apple part #922-7849) • Scissors t o cut access card in half Retrieving Mechanism
LED Cinema Display (24-inch) Additional Procedures — Retrieving Mechanism 90 2010-11-25 Removal 1 Place unit face down on a clean, soft surface. 2 Peer into stand slot to see recessed latch. Latch is a shiny metal spring clip located above mechanism that is almost as wide as stand slot. 3 Cut access card in half vertically, into two equal halves. 4 Insert half of access card into one end of stand slot and push latch away to get a sense of how latch moves.